User Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the main body
- Assembling the handlebar and throttle
- Connecting throttle cable and stop switch wires
- Fitting blades and trimmer heads
- Fitting the transport guard
- Adjusting the harness and brush cutter
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Air filter
- Fuel filter
- Bevel gear
- Spark plug
- Maintenance schedule
- Technical data
- EC Declaration of Conformity
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del cuerpo principal
- Montaje del manillar y la empuñadura de acelerador
- Conexión del cable de acelerador y los hilos del interruptor de parada
- Montaje de la hoja y del cabezal de corte
- Montaje de la protección para transportes
- Ajuste del arnés y la desbrozadora
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Filtro de aire
- Filtro de combustible
- Engranaje angulado
- Bujía
- Programa de mantenimiento
- Datos técnicos
- Declaración CE de conformidad
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Equipamento de corte
- Montagem da carcaça principal
- Montagem da direcção e do punho do acelerador
- Ligação do cabo do acelerador e dos fios do interruptor de paragem
- Montagem da lâmina e cabeçote de recorte
- Montagem da protecção para transporte
- Ajuste do suporte e do roçador
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Filtro de ar
- Filtro de combustível
- Engrenagem angular
- Vela de ignição
- Esquema de manutenção
- Especificações técnicas
- Certificado CE de conformidade
GENERAL SAFETY PRECAUTIONS
English – 9
under the heading Adjusting the harness and brush
cutter.
Check that the harness straps are correctly positioned.
Once the harness and machine have been adjusted,
check that the harness quick release works correctly.
Muffler
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to
the machine.
Locking nut
A locking nut is used to secure some types of cutting
attachment.
When fitting, tighten the nut in the opposite direction to the
direction of rotation of the cutting attachment. To remove
it, undo the nut in the same direction as the cutting
attachment rotates. (CAUTION! The nut has a left-hand
thread.) Tighten the nut using the socket spanner.
The nylon lining inside the locking nut must not be so worn
that you can turn it by hand. The lining should offer a
resistance of at least 1.5 Nm. The nut should be replaced
after it has been put on approx. 10 times.
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
• Reduce the risk of blade thrust.
• Obtain maximum cutting performance.
!
WARNING! The inside of the muffler
contain chemicals that may be
carcinogenic. Avoid contact with these
elements in the event of a damaged
muffler.
!
WARNING! Bear in mind that: The
exhaust fumes from the engine are hot
and may contain sparks which can start
a fire. Never start the machine indoors or
near combustible material!