Operator's Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Introduction
- To do a function check before you use the product
- Chain oil
- Common questions about kickback
- To connect the battery charger
- To charge the battery
- To start the product
- To use the SavE function
- To stop the product
- Kickback information
- To use the cutting technique
- To use the limbing technique
- To use the tree felling technique
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the battery and the battery compartment
- To do a check of the battery charger
- To clean the cooling system
- To sharpen the saw chain
- To tighten the saw chain
- To do a check of the saw chain lubrication
- To do the maintenance on the chain drive sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Accessories
- Warranty
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Introduction
- Pour vérifier le fonctionnement avant d’utiliser le produit
- Huile pour chaîne
- Questions fréquentes à propos du rebond
- Pour brancher le chargeur de batterie
- Pour charger la batterie
- Mise sous tension de l’appareil
- Pour utiliser la fonction SavE (économie)
- Mise hors tension de l’appareil
- Renseignements sur le rebond
- Pour utiliser la technique de coupe
- Pour utiliser la technique d’élagage
- Pour utiliser la technique d’abattage d’arbre
- Entretien
- Introduction
- Calendrier d’entretien
- Entretien et vérifications des dispositifs de sécurité du produit
- Pour vérifier la batterie et le compartiment de batterie
- Vérifier le chargeur de batterie
- Nettoyage du système de refroidissement
- Affûter la chaîne.
- Pour serrer la chaîne
- Vérification de la lubrification de la chaîne
- Pour effectuer l’entretien du pignon d’entraînement de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Dépannage
- Transport, entreposage et mise au rebut
- Données techniques
- Accessoires
- Garantie
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Introducción
- Para realizar una comprobación de funcionamiento antes de utilizar el producto
- Aceite para cadena
- Preguntas frecuentes acerca de las reculadas
- Para conectar el cargador de la batería
- Para cargar la batería
- Para poner en marcha la máquina
- Utilice la función de ahorro (SavE)
- Para detener la máquina
- Información de reculada
- Para utilizar la técnica de corte
- Para utilizar la técnica de desramado
- Para utilizar la técnica de tala
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad en el producto
- Para comprobar la batería y el compartimiento de la batería
- Para comprobar el cargador de la batería
- Para limpiar el sistema de refrigeración
- Para afilar la cadena de sierra
- Para apretar la cadena de sierra
- Para realizar una comprobación de la lubricación de la cadena de sierra
- Cómo realizar mantenimiento al piñón de arrastre de la cadena
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Accesorios
- Garantía
4. Keep a position where the tree or branch can not hit
you when the tension is released. (Fig. 90)
5. Make one or more cuts of sufficient depth necessary
to decrease the tension. Cut at or near the point of
maximum tension. Make the tree or branch break at
the point of maximum tension. (Fig. 91)
WARNING: Do not cut straight through a
tree or branch that is in tension.
WARNING: Be very careful when you
cut a tree that is in tension. There is a
risk that the tree moves quickly before or
after you cut it. Serious injury can occur
if you are in an incorrect position or if
you cut incorrectly.
6. If you must cut across tree/branch, make 2 to 3 cuts,
1 in. apart and with a depth of 2 in. (Fig. 92)
7. Continue to cut more into the tree until the tree/
branch bends and the tension is released. (Fig. 93)
8. Cut the tree/branch from the opposite side of the
bend, after the tension is released.
Maintenance
Introduction
WARNING: Read and understand the safety
chapter before you do maintenance on the
product.
Maintenance schedule
WARNING: Remove the battery before you
do maintenance.
The following is a list of the maintenance steps that you
must do on the product. See
Maintenance on page 20
for more information.
Maintenance Before
use
Weekly Monthly
Clean the external parts of the product. X
Make sure that the power trigger and the power trigger lockout function correctly
from a safety point of view.
X
Clean the chain brake and make sure that it operates safely. Make sure that the
chain catcher is not damaged. Replace it if necessary.
X
Turn the guide bar for more equal wear. Make sure that the lubrication hole in
the guide bar is not clogged. Clean the bar groove.
X
Make sure that the cutter and cutter guard have no cracks and that they are not
damaged. Replace the cutter or cutter guard if they have cracks or if they have
been exposed to impact.
X
Make sure that the guide bar and saw chain have sufficient oil. X
Do a check of the saw chain. Look for cracks and make sure that the saw chain
is not rigid or unusually worn. Replace if necessary.
X
Sharpen the saw chain. Do a check of its tension and condition. Do a check for
wear on the drive sprocket and replace is necessary.
X
Clean the air inlet on the product. X
Make sure that the screws and nuts are tight. X
Make sure that the keypad works correctly and that it is not damaged. X
20 1259 - 003 - 14.09.2020