Operator's Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Introduction
- To do a function check before you use the product
- Chain oil
- Common questions about kickback
- To connect the battery charger
- To charge the battery
- To start the product
- To use the SavE function
- To stop the product
- Kickback information
- To use the cutting technique
- To use the limbing technique
- To use the tree felling technique
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the battery and the battery compartment
- To do a check of the battery charger
- To clean the cooling system
- To sharpen the saw chain
- To tighten the saw chain
- To do a check of the saw chain lubrication
- To do the maintenance on the chain drive sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Accessories
- Warranty
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Introduction
- Pour vérifier le fonctionnement avant d’utiliser le produit
- Huile pour chaîne
- Questions fréquentes à propos du rebond
- Pour brancher le chargeur de batterie
- Pour charger la batterie
- Mise sous tension de l’appareil
- Pour utiliser la fonction SavE (économie)
- Mise hors tension de l’appareil
- Renseignements sur le rebond
- Pour utiliser la technique de coupe
- Pour utiliser la technique d’élagage
- Pour utiliser la technique d’abattage d’arbre
- Entretien
- Introduction
- Calendrier d’entretien
- Entretien et vérifications des dispositifs de sécurité du produit
- Pour vérifier la batterie et le compartiment de batterie
- Vérifier le chargeur de batterie
- Nettoyage du système de refroidissement
- Affûter la chaîne.
- Pour serrer la chaîne
- Vérification de la lubrification de la chaîne
- Pour effectuer l’entretien du pignon d’entraînement de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Dépannage
- Transport, entreposage et mise au rebut
- Données techniques
- Accessoires
- Garantie
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Introducción
- Para realizar una comprobación de funcionamiento antes de utilizar el producto
- Aceite para cadena
- Preguntas frecuentes acerca de las reculadas
- Para conectar el cargador de la batería
- Para cargar la batería
- Para poner en marcha la máquina
- Utilice la función de ahorro (SavE)
- Para detener la máquina
- Información de reculada
- Para utilizar la técnica de corte
- Para utilizar la técnica de desramado
- Para utilizar la técnica de tala
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad en el producto
- Para comprobar la batería y el compartimiento de la batería
- Para comprobar el cargador de la batería
- Para limpiar el sistema de refrigeración
- Para afilar la cadena de sierra
- Para apretar la cadena de sierra
- Para realizar una comprobación de la lubricación de la cadena de sierra
- Cómo realizar mantenimiento al piñón de arrastre de la cadena
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Accesorios
- Garantía
7. Turn the guide bar daily to extend its life cycle. (Fig.
136)
Troubleshooting
Troubleshooting schedule
Table 1: Keypad
Possible fault codes on the keypad of the product.
LED display Possible faults Possible action
Warning indicator flashing. Chain brake engaged. Pull back the front hand guard to re-
lease the chain brake.
Temperature deviation. Allow the product to cool down.
Overload. Cutting attachment jam-
med.
The cutting attachment is jammed.
Release the cutting attachment.
The power trigger and the activate
button are pressed at the same time.
Release the power trigger and the
product is active.
Green activate LED flashing. Low battery voltage. Charge the battery.
Warning indicator lit. Service. Turn to your servicing dealer.
Table 2: Battery
Troubleshooting the battery and/or the battery charger during charging.
LED display
Possible faults Possible action
Warning indicator flashing. The battery is discharged. Charge the battery.
Temperature deviation. Use the battery in surroundings
where tempereatures are between
-10 °C/14°F and 40°C/104°F.
Over voltage. Check that the mains voltage corre-
sponds with that stated on the rating
plate on the product.
Remove the battery from the battery
charger.
Warning indicator lit. Cell difference is too much (1V). Turn to your servicing dealer.
24 1259 - 003 - 14.09.2020