Operator's Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Introduction
- To do a function check before you use the product
- Chain oil
- Common questions about kickback
- To connect the battery charger
- To charge the battery
- To start the product
- To use the SavE function
- To stop the product
- Kickback information
- To use the cutting technique
- To use the limbing technique
- To use the tree felling technique
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the battery and the battery compartment
- To do a check of the battery charger
- To clean the cooling system
- To sharpen the saw chain
- To tighten the saw chain
- To do a check of the saw chain lubrication
- To do the maintenance on the chain drive sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Accessories
- Warranty
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Introduction
- Pour vérifier le fonctionnement avant d’utiliser le produit
- Huile pour chaîne
- Questions fréquentes à propos du rebond
- Pour brancher le chargeur de batterie
- Pour charger la batterie
- Mise sous tension de l’appareil
- Pour utiliser la fonction SavE (économie)
- Mise hors tension de l’appareil
- Renseignements sur le rebond
- Pour utiliser la technique de coupe
- Pour utiliser la technique d’élagage
- Pour utiliser la technique d’abattage d’arbre
- Entretien
- Introduction
- Calendrier d’entretien
- Entretien et vérifications des dispositifs de sécurité du produit
- Pour vérifier la batterie et le compartiment de batterie
- Vérifier le chargeur de batterie
- Nettoyage du système de refroidissement
- Affûter la chaîne.
- Pour serrer la chaîne
- Vérification de la lubrification de la chaîne
- Pour effectuer l’entretien du pignon d’entraînement de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Dépannage
- Transport, entreposage et mise au rebut
- Données techniques
- Accessoires
- Garantie
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Introducción
- Para realizar una comprobación de funcionamiento antes de utilizar el producto
- Aceite para cadena
- Preguntas frecuentes acerca de las reculadas
- Para conectar el cargador de la batería
- Para cargar la batería
- Para poner en marcha la máquina
- Utilice la función de ahorro (SavE)
- Para detener la máquina
- Información de reculada
- Para utilizar la técnica de corte
- Para utilizar la técnica de desramado
- Para utilizar la técnica de tala
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad en el producto
- Para comprobar la batería y el compartimiento de la batería
- Para comprobar el cargador de la batería
- Para limpiar el sistema de refrigeración
- Para afilar la cadena de sierra
- Para apretar la cadena de sierra
- Para realizar una comprobación de la lubricación de la cadena de sierra
- Cómo realizar mantenimiento al piñón de arrastre de la cadena
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Accesorios
- Garantía
120i
Battery runtime, min, (free run) in SavE model 42
Lubrication system
Type of oil pump Automatic
Oil tank capacity,US pint/litre 0.42/0.20
Weight
Chainsaw without battery, guide bar, saw chain and empty chain oil tank, lb/kg 6.5/2.95
Saw chain/guide bar
Recommended bar lengths, inch/cm 14/35
Usable cutting length, inch/cm 13/33
Type of drive sprocket/number of teeth Spur/6
Maximum chain speed / (savE), m/s 11.5 (10)
Accessories
Recommended cutting equipment for
USA
Following is a list of recommended cutting equipment for
Husqvarna cordless 120i. This model equipped with
either of the listed guide bar and saw chain
combination(s), fulfills the requirements according to UL
60745-2-13.
Chainsaw model Husqvarna 120i met the kickback
performance requirements of UL 60745-2-13 when
tested with the combinations of bars and saw chains
listed below. The saw chain Husqvarna H37/H38 is also
classified as a low kickback saw chain since is met the
requirements for low kickback saw chain outlined in UL
60745-2-13. We recommend to use only the listed
combinations of bars and saw chains for chainsaw
model Husqvarna 120i. Other chainsaw models may not
meet the kickback requirements when equipped with the
listed bar and saw chain combinations.
Recommended cutting equipment for
Canada
Following is a list of recommended cutting equipment for
the Husqvarna cordless chainsaw 120i. The listed
combination(s) of powerhead, guide bar and saw chain
meet all requirements outlined in Canadian Standards
Assosiation Z62.1-11 (Chain Saws) and Z62.3-11
(Chain Saw Kickback).
Furthermore the saw chain Husqvarna H37/H38 is
evaluated and listed as a Type C Low Kickback Saw
chain according to the provisions in Z62.3-11.
Guide bar and saw chain combinations
The following cutting attachments are approved for
Husqvarna 120i.
Guide bar
Saw chain
Length, in Chain pitch, in Gauge, in Max. nose radius Type Length, drive
links (no.)
14 3/8 0.050 7T Husqvarna H37 52
14 3/8 0.043 7T Husqvarna H38 52
Note: Depending on your model version of Husqvarna
120i, you must make sure that you put together the
correct guide bar and saw chain (0.050 gauge bar= H37
and 0.043 gauge bar= H38). The chainsaw will not
operate correctly with the incorrect combination of guide
bar and saw chain.
26 1259 - 003 - 14.09.2020