Operator's Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Introduction
- To do a function check before you use the product
- Chain oil
- Common questions about kickback
- To connect the battery charger
- To charge the battery
- To start the product
- To use the SavE function
- To stop the product
- Kickback information
- To use the cutting technique
- To use the limbing technique
- To use the tree felling technique
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the battery and the battery compartment
- To do a check of the battery charger
- To clean the cooling system
- To sharpen the saw chain
- To tighten the saw chain
- To do a check of the saw chain lubrication
- To do the maintenance on the chain drive sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Accessories
- Warranty
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Introduction
- Pour vérifier le fonctionnement avant d’utiliser le produit
- Huile pour chaîne
- Questions fréquentes à propos du rebond
- Pour brancher le chargeur de batterie
- Pour charger la batterie
- Mise sous tension de l’appareil
- Pour utiliser la fonction SavE (économie)
- Mise hors tension de l’appareil
- Renseignements sur le rebond
- Pour utiliser la technique de coupe
- Pour utiliser la technique d’élagage
- Pour utiliser la technique d’abattage d’arbre
- Entretien
- Introduction
- Calendrier d’entretien
- Entretien et vérifications des dispositifs de sécurité du produit
- Pour vérifier la batterie et le compartiment de batterie
- Vérifier le chargeur de batterie
- Nettoyage du système de refroidissement
- Affûter la chaîne.
- Pour serrer la chaîne
- Vérification de la lubrification de la chaîne
- Pour effectuer l’entretien du pignon d’entraînement de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Dépannage
- Transport, entreposage et mise au rebut
- Données techniques
- Accessoires
- Garantie
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Introducción
- Para realizar una comprobación de funcionamiento antes de utilizar el producto
- Aceite para cadena
- Preguntas frecuentes acerca de las reculadas
- Para conectar el cargador de la batería
- Para cargar la batería
- Para poner en marcha la máquina
- Utilice la función de ahorro (SavE)
- Para detener la máquina
- Información de reculada
- Para utilizar la técnica de corte
- Para utilizar la técnica de desramado
- Para utilizar la técnica de tala
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad en el producto
- Para comprobar la batería y el compartimiento de la batería
- Para comprobar el cargador de la batería
- Para limpiar el sistema de refrigeración
- Para afilar la cadena de sierra
- Para apretar la cadena de sierra
- Para realizar una comprobación de la lubricación de la cadena de sierra
- Cómo realizar mantenimiento al piñón de arrastre de la cadena
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Accesorios
- Garantía
(Fig. 15) Environmental mark. The product or
package of the product is not domestic
waste. Recycle it at a recycling station for
electrical and electronic equipment.
(Fig. 19) The rating plate shows serial number. yyyy
is the production year, ww is the production
week.
Note: Other symbols/decals on the product refer to
certification requirements for some markets.
Symbols on the battery and/or on the
battery charger
(Fig. 20)
Recycle this product at a recycling station
for electrical and electronic equipment. (Ap-
plies to Europe only)
(Fig. 16) Fail-safe transformer.
(Fig. 17) Use and keep the battery charger indoors
only.
(Fig. 18) Double insulation.
Customer assistance
For customer assistance, call: 1-800-487-5951 or visit
www.usa.husqvarna.com.
California Proposition 65
Safety
Safety definitions
The definitions below give the level of severity for each
signal word.
WARNING: Injury to persons.
CAUTION: Damage to the product.
Note: This information makes the product easier to use.
General power tool safety warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/or serious injury.
Note: Save all warnings and instructions for future
reference. The term "power tool" in the warnings refers
to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
Work area safety
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
•
Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
Electrical safety
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
Personal safety
• Stay alert, monitor what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
1259 - 003 - 14.09.2020
9