Owner's manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear customer!
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the loop handle
- Assembling the cutting equipment
- Fuel handling
- Fuel
- Check before starting
- Starting and stopping
- General working instructions
- Carburetor
- Muffler
- Cooling system
- Spark plug
- Air filter
- Maintenance schedule
- Technical data
- YOUR WARRANTY RIGHTS AND OBLIGATIONS
- MANUFACTURER¢S WARRANTY COVERAGE
- OWNER¢S WARRANTY RESPONSIBILITIES
- WARRANTY COMMENCEMENT DATE
- LENGTH OF COVERAGE
- WHAT IS COVERED
- EMISSION WARRANTY PARTS LIST
- WHAT IS NOT COVERED
- HOW TO FILE A CLAIM
- WHERE TO GET WARRANTY SERVICE
- MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
- MAINTENANCE STATEMENT
- Symboles
- Sommaire
- Contrôler les points suivants avant la mise en marche:
- Cher client,
- Important!
- Équipement de protection personnelle
- Équipement de sécurité de la machine
- Équipement de coupe
- Montage de la poignée en boucle
- Montage de l’équipement de coupe
- Manipulation du carburant
- Carburant
- Contrôles avant la mise en marche
- Démarrage et arrêt
- Méthodes de travail
- Carburateur
- Silencieux
- Système de refroidissement
- Bougie
- Filtre à air
- Schéma d’entretien
- Caractéristiques techniques
- VOS DROITS ET OBLIGATIONS EN GARANTIE
- GARANTIE DU FABRICANT
- CHARGES DE LA GARANTIE DE L’UTILISATEUR
- DATE D’ENTRÉE EN VIGUEUR DE LA GARANTIE
- DURÉE DE LA GARANTIE
- CE QUI EST COUVERT PAR LA GARANTIE
- LISTE DES PIÈCES GARANTIE ÉMISSIONS
- CE QUI N’EST PAS COUVERT PAR LA GARANTIE
- DEMANDE D’INDEMNITÉ
- SERVICE APRÈS-VENTE
- ENTRETIEN, REMPLACEMENT ET RÉPARATION DES PIÈCES DU SYSTÈME DE LUTTE CONTRE LES ÉMISSIONS
- DÉCLARATION D’ENTRETIEN
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del mango de tipo cerrado
- Montaje del equipo de corte
- Manipulación del combustible
- Carburante
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Silenciador
- Sistema refrigerante
- Bujía
- Filtro de aire
- Programa de mantenimiento
- Datos técnicos
- SUS DERECHOS Y OBLIGACIONES DE GARANTIA
- ALCANCE DE LA GARANTIA DEL FABRICANTE
- RESPONSABILIDADES DE GARANTIA DEL PROPIETARIO
- FECHA DE INICIO DE LA GARANTIA
- DURACION DE LA GARANTIA
- ALCANCE DE LA GARANTIA
- LISTA DE PIEZAS DE LA GARANTÍA DE EMISIONES
- LO QUE NO ABARCA LA GARANTIA
- COMO HACER UNA RECLAMACION
- DONDE RECIBIR SERVICIO DE GARANTIA
- MANTENIMIENTO, SUSTITUCION Y REPARACION DE COMPONENTES RELACIONADOS CON EMISIONES
- DECLARACION DE MANTENIMIENTO
FUEL HANDLING
English – 13
1155650-49 Rev. 3 2016-11-08
Oil level
The machine must be switched off and placed on a flat
surface when you check the oil level.
Unscrew the oil cap, clean the dipstick located on the cap
and insert the cap again without screwing it down. Check
the oil level on the dipstick.
When the oil level is low, top up using engine oil to the
edge of the oil refill hole.
Only use recommended engine oil.
Fueling
Always use a fuel container with an anti-spill valve.
Clean around the fuel cap. Clean the fuel and oil tank
regularly. The fuel filter should be changed at least once
a year. Contamination in the tanks causes malfunction.
Always move the machine about 3 metres from the
refuelling position before starting.
!
WARNING! Taking the following
precautions, will lessen the risk of fire:
Do not smoke or place hot objects near
fuel.
Always shut off the engine before
refueling.
Always stop the engine and let it cool for
a few minutes before refueling.
Always mix the gasoline and oil in a
clean container intended for fuel. Mix and
pour fuel outdoors, where there are no
sparks or flames.
When refuelling, open the fuel cap slowly
so that any excess pressure is released
gently.
Tighten the fuel cap carefully after
refueling.
Always move the machine away from the
refueling area and source before
starting.