Owner's manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear customer!
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the loop handle
- Assembling the cutting equipment
- Fuel handling
- Fuel
- Check before starting
- Starting and stopping
- General working instructions
- Carburetor
- Muffler
- Cooling system
- Spark plug
- Air filter
- Maintenance schedule
- Technical data
- YOUR WARRANTY RIGHTS AND OBLIGATIONS
- MANUFACTURER¢S WARRANTY COVERAGE
- OWNER¢S WARRANTY RESPONSIBILITIES
- WARRANTY COMMENCEMENT DATE
- LENGTH OF COVERAGE
- WHAT IS COVERED
- EMISSION WARRANTY PARTS LIST
- WHAT IS NOT COVERED
- HOW TO FILE A CLAIM
- WHERE TO GET WARRANTY SERVICE
- MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
- MAINTENANCE STATEMENT
- Symboles
- Sommaire
- Contrôler les points suivants avant la mise en marche:
- Cher client,
- Important!
- Équipement de protection personnelle
- Équipement de sécurité de la machine
- Équipement de coupe
- Montage de la poignée en boucle
- Montage de l’équipement de coupe
- Manipulation du carburant
- Carburant
- Contrôles avant la mise en marche
- Démarrage et arrêt
- Méthodes de travail
- Carburateur
- Silencieux
- Système de refroidissement
- Bougie
- Filtre à air
- Schéma d’entretien
- Caractéristiques techniques
- VOS DROITS ET OBLIGATIONS EN GARANTIE
- GARANTIE DU FABRICANT
- CHARGES DE LA GARANTIE DE L’UTILISATEUR
- DATE D’ENTRÉE EN VIGUEUR DE LA GARANTIE
- DURÉE DE LA GARANTIE
- CE QUI EST COUVERT PAR LA GARANTIE
- LISTE DES PIÈCES GARANTIE ÉMISSIONS
- CE QUI N’EST PAS COUVERT PAR LA GARANTIE
- DEMANDE D’INDEMNITÉ
- SERVICE APRÈS-VENTE
- ENTRETIEN, REMPLACEMENT ET RÉPARATION DES PIÈCES DU SYSTÈME DE LUTTE CONTRE LES ÉMISSIONS
- DÉCLARATION D’ENTRETIEN
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del mango de tipo cerrado
- Montaje del equipo de corte
- Manipulación del combustible
- Carburante
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Silenciador
- Sistema refrigerante
- Bujía
- Filtro de aire
- Programa de mantenimiento
- Datos técnicos
- SUS DERECHOS Y OBLIGACIONES DE GARANTIA
- ALCANCE DE LA GARANTIA DEL FABRICANTE
- RESPONSABILIDADES DE GARANTIA DEL PROPIETARIO
- FECHA DE INICIO DE LA GARANTIA
- DURACION DE LA GARANTIA
- ALCANCE DE LA GARANTIA
- LISTA DE PIEZAS DE LA GARANTÍA DE EMISIONES
- LO QUE NO ABARCA LA GARANTIA
- COMO HACER UNA RECLAMACION
- DONDE RECIBIR SERVICIO DE GARANTIA
- MANTENIMIENTO, SUSTITUCION Y REPARACION DE COMPONENTES RELACIONADOS CON EMISIONES
- DECLARACION DE MANTENIMIENTO
MAINTENANCE
18 – English
1155650-49 Rev. 3 2016-11-08
Carburetor
Function
• The carburetor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the
carburetor.
• Setting the carburettor involves adapting the engine to
suit local conditions, e.g. climate, altitude and the
petrol.
Basic setting
The basic carburetor settings are adjusted during testing
at the factory.
CAUTION! For optimum adjustment of the carburettor,
contact a qualified dealer/service workshop that has a
revolution counter at their disposal.
Adjusting the idle speed (T)
Check that the air filter is clean. When the idle speed is
correct, the cutting attachment should not rotate. If
adjustment is required, close (turn clockwise) the idle
adjustment screw T, with the engine running, until the
cutting attachment starts to rotate. Open (turn
anticlockwise) the screw until the cutting attachment
stops. The idle speed is correctly set when the engine
runs smoothly in all positions, and there is a clear margin
to the speed at which the cutting attachment starts to
rotate.
Muffler
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether
your machine is fitted with a catalytic converter.
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible
material.
The muffler on your machine is equipped with a spark
arrestor screen, this should be cleaned regularly. A
blocked screen will cause the engine to overheat and may
lead to serious damage.
CAUTION! Never use a machine with a defective muffler.
Cooling system
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until
it has been correctly adjusted or
repaired.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!