Owner's manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear customer!
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the loop handle
- Assembling the cutting equipment
- Fuel handling
- Fuel
- Check before starting
- Starting and stopping
- General working instructions
- Carburetor
- Muffler
- Cooling system
- Spark plug
- Air filter
- Maintenance schedule
- Technical data
- YOUR WARRANTY RIGHTS AND OBLIGATIONS
- MANUFACTURER¢S WARRANTY COVERAGE
- OWNER¢S WARRANTY RESPONSIBILITIES
- WARRANTY COMMENCEMENT DATE
- LENGTH OF COVERAGE
- WHAT IS COVERED
- EMISSION WARRANTY PARTS LIST
- WHAT IS NOT COVERED
- HOW TO FILE A CLAIM
- WHERE TO GET WARRANTY SERVICE
- MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
- MAINTENANCE STATEMENT
- Symboles
- Sommaire
- Contrôler les points suivants avant la mise en marche:
- Cher client,
- Important!
- Équipement de protection personnelle
- Équipement de sécurité de la machine
- Équipement de coupe
- Montage de la poignée en boucle
- Montage de l’équipement de coupe
- Manipulation du carburant
- Carburant
- Contrôles avant la mise en marche
- Démarrage et arrêt
- Méthodes de travail
- Carburateur
- Silencieux
- Système de refroidissement
- Bougie
- Filtre à air
- Schéma d’entretien
- Caractéristiques techniques
- VOS DROITS ET OBLIGATIONS EN GARANTIE
- GARANTIE DU FABRICANT
- CHARGES DE LA GARANTIE DE L’UTILISATEUR
- DATE D’ENTRÉE EN VIGUEUR DE LA GARANTIE
- DURÉE DE LA GARANTIE
- CE QUI EST COUVERT PAR LA GARANTIE
- LISTE DES PIÈCES GARANTIE ÉMISSIONS
- CE QUI N’EST PAS COUVERT PAR LA GARANTIE
- DEMANDE D’INDEMNITÉ
- SERVICE APRÈS-VENTE
- ENTRETIEN, REMPLACEMENT ET RÉPARATION DES PIÈCES DU SYSTÈME DE LUTTE CONTRE LES ÉMISSIONS
- DÉCLARATION D’ENTRETIEN
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del mango de tipo cerrado
- Montaje del equipo de corte
- Manipulación del combustible
- Carburante
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Silenciador
- Sistema refrigerante
- Bujía
- Filtro de aire
- Programa de mantenimiento
- Datos técnicos
- SUS DERECHOS Y OBLIGACIONES DE GARANTIA
- ALCANCE DE LA GARANTIA DEL FABRICANTE
- RESPONSABILIDADES DE GARANTIA DEL PROPIETARIO
- FECHA DE INICIO DE LA GARANTIA
- DURACION DE LA GARANTIA
- ALCANCE DE LA GARANTIA
- LISTA DE PIEZAS DE LA GARANTÍA DE EMISIONES
- LO QUE NO ABARCA LA GARANTIA
- COMO HACER UNA RECLAMACION
- DONDE RECIBIR SERVICIO DE GARANTIA
- MANTENIMIENTO, SUSTITUCION Y REPARACION DE COMPONENTES RELACIONADOS CON EMISIONES
- DECLARACION DE MANTENIMIENTO
22 – English
TECHNICAL DATA
1155650-49 Rev. 3 2016-11-08
Technical data
Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under
various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.
NOTE! This spark ignition system complies with the Canadian ICES-002 standard.
NOTE! The sound pressure level at operator’s ear and vibrations on the handles are measured with all the approved
cutting attachments for the machine. The table indicates the lowest and highest values.
224L
Engine
Cylinder displacement, cu.in/cm
3
1,53/25,0
Cylinder bore, inch/mm 1,38/35
Stroke, inch/mm 1,03/26
Idle speed, rpm 3100
Recommended max. speed, rpm 12000
Speed of output shaft, rpm 8220
Max. engine output, acc. to ISO 8893, kW/ rpm 0,8 / 7000
Catalytic converter muffler No
Speed-regulated ignition system No
Ignition system
Manufacturer/type of ignition system Ikeda
Spark plug NGK CMR5H
Electrode gap, inch/mm 0,024/0,6
Fuel and lubrication system
Manufacturer/type of carburetor Walbro
Fuel tank capacity, US pint/litre 1,16/0,55
Weight
Weight without fuel, cutting attachment and guard, Lbs/kg 11.0/5,0
Sound levels
(see note 1)
Equivalent sound pressure level at the user′s ear, measured according to ANSI B175.3-2013,
dB(A), min/max:
90/97
Vibration levels
Vibration levels at handles, measured according to ANSI B175.3-2013, m/s
2
At idle, left/right handles, min.: 1,9/1,8
At idle, left/right handles, max.: 2,2/1,9
At max. speed, left/right handles, min.: 4,8/11,3
At max. speed, left/right handles, max.: 8,9/14,0
224L
Approved accessories Type Cutting attachment guard, Art. no.
Arbor shaft thread M10
Trimmer head
S35 503 97 71-01 / 588 11 79-01
T25 503 97 71-01 / 588 11 79-01
T35 503 97 71-01 / 588 11 79-01
Alloy (Ø 2.0 - 3.3 mm cord) 503 97 71-01 / 588 11 79-01