Operating Guide
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- To adjust the idle speed
- To do maintenance on the muffler
- Cooling system
- To examine the spark plug
- Air filter
- Two piece-shaft
- To check the chain drive sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To sharpen the saw chain
- Information about the guide bar and saw chain
- General information about how to sharpen the cutters
- To sharpen the cutters
- General information about how to adjust the depth gauge setting
- To adjust the depth gauge setting
- To tension the chain
- To fill with chain oil
- To check the chain lubrication
- To adjust chain lubrication
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Accessories
- Warranty
- Contenido
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Para ajustar el régimen de ralentí
- Para realizar tareas de mantenimiento en el silenciador
- Sistema refrigerante
- Para examinar la bujía
- Filtro de aire
- Eje de dos piezas
- Para comprobar el piñón de arrastre de la cadena
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Para afilar la cadena de sierra
- Información sobre la espada guía y la cadena de sierra
- Información general sobre cómo afilar las cortadoras
- Para afilar las cortadoras
- Información general sobre cómo ajustar la configuración del calibre de profundidad
- Para ajustar el calibre de profundidad
- Para tensar la cadena
- Para llenar con aceite para cadena
- Para comprobar la lubricación de la cadena
- Para ajustar la lubricación de la cadena
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Accesorios
- Garantía
- Table des matières
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Entretien
- Introduction
- Calendrier d’entretien
- Réglage du régime de ralenti
- Pour entretenir le silencieux
- Système de refroidissement
- Vérification de la bougie d’allumage
- Filtre à air
- Arbre en deux pièces
- Pour vérifier le pignon d’entraînement de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Affûter la chaîne.
- Renseignements à propos du guide-chaîne et de la chaîne
- Renseignements généraux sur comment affûter les découpeuses.
- Pour affûter les découpeuses
- Renseignements généraux sur comment ajuster le réglage de la jauge de profondeur
- Réglage de la jauge de profondeur
- Pour tendre la chaîne
- Pour remplir au moyen d’huile pour chaîne
- Pour vérifier la lubrification de la chaîne
- Pour régler la lubrification de la chaîne
- Dépannage
- Transport, entreposage et mise au rebut
- Données techniques
- Accessoires
- Garantie
Maintenance Daily Weekly Monthly
Clean the air filter. Replace if necessary. X
Check the saw chain with regard to visible cracks in the rivets and links, whether
the saw chain is stiff or whether the rivets and links are abnormally worn.
X
Clean the area under the protective cover. X
Make sure that the screws and nuts are tight. X
Examine the engine, the fuel tank and the fuel lines for leaks. X
Clean the cooling system. X
Examine the starter and the starter rope for damages. X
Examine the vibration damping elements for damages and cracks. X
Clean the outside of the spark plug. Remove it and do a check of the electrode
gap. Adjust the gap to the correct distance (refer to
To examine the spark plug
on page 17
) or replace the spark plug. Make sure that the spark plug is fitted
with a suppressor.
X
Clean the outside of the carburetor and the space around it. X
File off any burrs from the edges of the bar. X
Clean or replace the spark arrestor screen on the muffler. X
Clean the fuel tank. X
Do a check of the fuel filter for contamination and the fuel hose for cracks or oth-
er defects. Replace if necessary.
X
Do a check of all cables and connections. X
Do a check of the clutch, clutch springs and the clutch drum for wear. Replace if
necessary by an authorized service workshop.
X
Examine the spark plug. Replace the spark plug if it is necessary. X
Do an inspection of the dielectric shaft for worn and damaged areas. Do not use
the product if the dielectric shaft has worn or damaged areas. Refer to OSHA
1910.269 for more information.
X
To adjust the idle speed
1. Make sure that the air filter is clean and the air filter
cover is attached before you adjust the idle speed.
2. Start the product. Refer to
To start the product on
page 14
3. Adjust the idle speed with the idle adjustment screw
T which is identified with "T" mark. Turn the idle
adjustment screw clockwise until the saw chain
starts to turn.
4. Turn the idle adjustment screw counterclockwise
until the saw chain stops.
16 703 - 005 - 20.10.2020