Operating Guide
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- To adjust the idle speed
- To do maintenance on the muffler
- Cooling system
- To examine the spark plug
- Air filter
- Two piece-shaft
- To check the chain drive sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To sharpen the saw chain
- Information about the guide bar and saw chain
- General information about how to sharpen the cutters
- To sharpen the cutters
- General information about how to adjust the depth gauge setting
- To adjust the depth gauge setting
- To tension the chain
- To fill with chain oil
- To check the chain lubrication
- To adjust chain lubrication
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Accessories
- Warranty
- Contenido
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Para ajustar el régimen de ralentí
- Para realizar tareas de mantenimiento en el silenciador
- Sistema refrigerante
- Para examinar la bujía
- Filtro de aire
- Eje de dos piezas
- Para comprobar el piñón de arrastre de la cadena
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Para afilar la cadena de sierra
- Información sobre la espada guía y la cadena de sierra
- Información general sobre cómo afilar las cortadoras
- Para afilar las cortadoras
- Información general sobre cómo ajustar la configuración del calibre de profundidad
- Para ajustar el calibre de profundidad
- Para tensar la cadena
- Para llenar con aceite para cadena
- Para comprobar la lubricación de la cadena
- Para ajustar la lubricación de la cadena
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Accesorios
- Garantía
- Table des matières
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Entretien
- Introduction
- Calendrier d’entretien
- Réglage du régime de ralenti
- Pour entretenir le silencieux
- Système de refroidissement
- Vérification de la bougie d’allumage
- Filtre à air
- Arbre en deux pièces
- Pour vérifier le pignon d’entraînement de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Affûter la chaîne.
- Renseignements à propos du guide-chaîne et de la chaîne
- Renseignements généraux sur comment affûter les découpeuses.
- Pour affûter les découpeuses
- Renseignements généraux sur comment ajuster le réglage de la jauge de profondeur
- Réglage de la jauge de profondeur
- Pour tendre la chaîne
- Pour remplir au moyen d’huile pour chaîne
- Pour vérifier la lubrification de la chaîne
- Pour régler la lubrification de la chaîne
- Dépannage
- Transport, entreposage et mise au rebut
- Données techniques
- Accessoires
- Garantie
Transportation, storage and disposal
Transportation and storage
• For storage and transportation of the product and
fuel, make sure that there are no leaks or fumes.
Sparks or open flames, for example from electrical
devices or boilers, can start a fire.
• Always use approved containers for storage and
transportation of fuel.
• Empty the fuel and chain oil tanks before
transportation or before long-term storage. Discard
the fuel and chain oil at an applicable disposal
location.
• Use the transportation guard on the product to
prevent injuries or damage to the product. A saw
chain that does not move can also cause serious
injuries.
• Remove the spark plug cap from the spark plug.
• Attach the product safely during transportation.
To prepare your product for long-term
storage
1. Disassemble and clean the saw chain and the
groove in the guide bar.
CAUTION: If the saw chain and guide
bar are not cleaned, they can become
rigid or blocked.
2. Attach the transportation guard.
3. Clean the product. Refer to
Maintenance on page 15
for instructions.
4. Do a complete servicing of the product.
Technical data
Technical data
525P4S 525P5S
Engine
Cylinder displacement, cu.in/cm
3
1.55/25.4 1.55/25.4
Cylinder bore, inch/mm 1.34/34 1.34/34
Stroke, inch/mm 1.10/28 1.10/28
Recommended max. speed, rpm 11000-12000 11000-12000
Idle speed, rpm 2800-3000 2800-3000
Max. engine output, according to ISO 8893, kW/rpm 1.0/8500 1.0/8500
Catalytic converter muffler Yes Yes
Speed-regulated ignition system Yes Yes
Ignition system
Spark plug NGK BPMR8Y NGK BPMR8Y
Electrode gap, inch/mm 0.026/0.65 0.026/0.65
Fuel and lubrication system
Fuel tank capacity, US Pint/litre 1.06/0.5 1.06/0.5
Oil tank capacity, US Pint/litre 0.4/0.2 0.4/0.2
Weight
Without fuel, cutting attachment and guard, Lbs/kg 11.7/5.3 14.1/6.4
24 703 - 005 - 20.10.2020