Operating Guide
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- To adjust the idle speed
- To do maintenance on the muffler
- Cooling system
- To examine the spark plug
- Air filter
- To check the chain drive sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To sharpen the saw chain
- Information about the guide bar and saw chain
- General information about how to sharpen the cutters
- To sharpen the cutters
- General information about how to adjust the depth gauge setting
- To adjust the depth gauge setting
- To tension the chain
- To fill with chain oil
- To check the chain lubrication
- To adjust chain lubrication
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Accessories
- Warranty
- Contenido
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Para ajustar el régimen de ralentí
- Para realizar tareas de mantenimiento en el silenciador
- Sistema refrigerante
- Para examinar la bujía
- Filtro de aire
- Para comprobar el piñón de arrastre de la cadena
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Para afilar la cadena de sierra
- Información sobre la espada guía y la cadena de sierra
- Información general sobre cómo afilar las cortadoras
- Para afilar las cortadoras
- Información general sobre cómo ajustar la configuración del calibre de profundidad
- Para ajustar el calibre de profundidad
- Para tensar la cadena
- Para llenar con aceite para cadena
- Para comprobar la lubricación de la cadena
- Para ajustar la lubricación de la cadena
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Accesorios
- Garantía
- Table des matières
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Entretien
- Introduction
- Calendrier d’entretien
- Réglage du régime de ralenti
- Pour entretenir le silencieux
- Système de refroidissement
- Vérification de la bougie d’allumage
- Filtre à air
- Pour vérifier le pignon d’entraînement de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Affûter la chaîne.
- Renseignements à propos du guide-chaîne et de la chaîne
- Renseignements généraux sur comment affûter les découpeuses.
- Pour affûter les découpeuses
- Renseignements généraux sur comment ajuster le réglage de la jauge de profondeur
- Réglage de la jauge de profondeur
- Pour tendre la chaîne
- Pour remplir au moyen d’huile pour chaîne
- Pour vérifier la lubrification de la chaîne
- Pour régler la lubrification de la chaîne
- Dépannage
- Transport, entreposage et mise au rebut
- Données techniques
- Accessoires
- Garantie
• Chain oil hole and hole for chain tensioner. The
guide bar must align with product.
• Drive link width, mm/in.
General information about how to sharpen the
cutters
Do not use a blunt saw chain. If the saw chain is blunt,
you must apply more pressure to push the guide bar
through the wood. If the saw chain is very blunt, there
will be no wood chips but sawdust.
A sharp saw chain eats through the wood and the wood
chips becomes long and thick.
The cutting tooth (A) and the depth gauge (B) together
makes the cutting part of the saw chain, the cutter. The
difference in height between the two gives the cutting
depth (depth gauge setting).
A
B
When you sharpen the cutter, think about the following:
• Filing angle.
• Cutting angle.
• File position.
• Round file diameter.
It is not easy to sharpen a saw chain correctly without
the correct equipment. Use Husqvarna file gauge. This
will help you to keep maximum cutting performance.
Note: Refer to
To sharpen the cutters on page 20
for
information about sharpening of the saw chain.
To sharpen the cutters
1. Use a round file and a file gauge to sharpen the
cutting teeth.
Note:
Refer to
Accessories on page 24
for
information about which file and gauge that
Husqvarna recommends for your saw chain.
2. Apply the file gauge correctly on to the cutter. Refer
to the instruction supplied with the file gauge.
20
712 - 004 - 30.09.2020