Operating Guide
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- To adjust the idle speed
- To do maintenance on the muffler
- Cooling system
- To examine the spark plug
- Air filter
- To check the chain drive sprocket
- To examine the cutting equipment
- To do a check of the guide bar
- To sharpen the saw chain
- Information about the guide bar and saw chain
- General information about how to sharpen the cutters
- To sharpen the cutters
- General information about how to adjust the depth gauge setting
- To adjust the depth gauge setting
- To tension the chain
- To fill with chain oil
- To check the chain lubrication
- To adjust chain lubrication
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Accessories
- Warranty
- Contenido
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Para ajustar el régimen de ralentí
- Para realizar tareas de mantenimiento en el silenciador
- Sistema refrigerante
- Para examinar la bujía
- Filtro de aire
- Para comprobar el piñón de arrastre de la cadena
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Para afilar la cadena de sierra
- Información sobre la espada guía y la cadena de sierra
- Información general sobre cómo afilar las cortadoras
- Para afilar las cortadoras
- Información general sobre cómo ajustar la configuración del calibre de profundidad
- Para ajustar el calibre de profundidad
- Para tensar la cadena
- Para llenar con aceite para cadena
- Para comprobar la lubricación de la cadena
- Para ajustar la lubricación de la cadena
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Accesorios
- Garantía
- Table des matières
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Entretien
- Introduction
- Calendrier d’entretien
- Réglage du régime de ralenti
- Pour entretenir le silencieux
- Système de refroidissement
- Vérification de la bougie d’allumage
- Filtre à air
- Pour vérifier le pignon d’entraînement de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Affûter la chaîne.
- Renseignements à propos du guide-chaîne et de la chaîne
- Renseignements généraux sur comment affûter les découpeuses.
- Pour affûter les découpeuses
- Renseignements généraux sur comment ajuster le réglage de la jauge de profondeur
- Réglage de la jauge de profondeur
- Pour tendre la chaîne
- Pour remplir au moyen d’huile pour chaîne
- Pour vérifier la lubrification de la chaîne
- Pour régler la lubrification de la chaîne
- Dépannage
- Transport, entreposage et mise au rebut
- Données techniques
- Accessoires
- Garantie
Safety devices on the product
WARNING: Read the warning instructions
that follow before you use the product.
• Do not use a product with defective safety devices.
• Do a check of the safety devices regularly. Refer to
Safety devices on the product on page 7
.
• If the safety devices are defective, speak to your
Husqvarna servicing dealer.
To do a check of the throttle trigger lockout
The throttle trigger lockout prevents accidental operation
of the throttle control.
1. Push the throttle trigger lockout (A) and make sure
that the throttle control is released (B). When you
release the handle, the throttle control and the
throttle trigger lockout move back to their initial
positions.
A
B
2. Release the throttle trigger lockout and make sure
that the throttle control is locked at idle speed.
3. Push the throttle trigger lockout and make sure that it
goes back to its initial position when you release it.
4. Make sure that the throttle control and throttle trigger
lockout move freely and that the return springs
operate correctly.
5. Start the product and apply full throttle. Refer to
To
start the product on page 14
.
6. Release the throttle control and make sure that the
cutting attachment stops. If the cutting attachment
rotates with the throttle in the idle position, do a
check of the carburetor adjustments. Refer to
Maintenance on page 15
.
To do a check of the stop switch
1. Start the engine.
2. Move the stop switch to the stop position and make
sure that the engine stops.
To do a check of the vibration damping system
The vibration damping system decreases vibration in the
handles to a minimum which makes the operation
easier. The vibration damping system of the product
decreases the transfer of vibration between the engine
unit and the shaft unit of the product.
1. Stop the engine.
712 - 004 - 30.09.2020
7