Operating Guide
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- To adjust the idle speed screw (T)
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To do a check of the saw chain lubrication
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- Air cleaning system
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- Warranty
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Introducción
- Para realizar una comprobación de funcionamiento antes de utilizar el producto
- Combustible
- Información de reculada
- Para poner en marcha la máquina
- Para detener la máquina
- Corte de tracción y corte de empuje
- Para utilizar la técnica de corte
- Para utilizar la técnica de desramado
- Para utilizar la técnica de tala
- Para utilizar el producto en climas fríos
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad en el producto
- Para comprobar la cinta de freno
- Para comprobar la protección contra reculadas y la activación del freno de cadena
- Para revisar el freno de cadena
- Para comprobar el acelerador y el bloqueo del acelerador
- Para comprobar el captor de cadena
- Para comprobar la protección de la mano derecha
- Para comprobar el sistema amortiguador de vibraciones
- Para comprobar el interruptor de arranque/detención
- Para comprobar el silenciador
- Para ajustar el tornillo del régimen de ralentí (T)
- Para examinar si el carburador está correctamente ajustado
- Para reemplazar una cuerda de arranque rota o desgastada
- Para apretar el resorte de retorno
- Para montar el cuerpo del mecanismo de arranque en el producto
- Para limpiar el filtro de aire
- Para comprobar la bujía
- Para afilar la cadena de sierra
- Para realizar una comprobación de la lubricación de la cadena de sierra
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Para realizar mantenimiento en el depósito de combustible y en el depósito de aceite para cadena
- Sistema de purificación de aire
- Para limpiar el sistema de refrigeración
- Solución de problemas
- Transporte y almacenamiento
- Datos técnicos
- Accesorios
- Garantía
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Introduction
- Pour vérifier le fonctionnement avant d’utiliser le produit
- Carburant
- Renseignements sur le rebond
- Mise sous tension de l’appareil
- Arrêt de la machine
- Méthode tirée et méthode poussée
- Pour utiliser la technique de coupe
- Pour utiliser la technique d’élagage
- Pour utiliser la technique d’abattage d’arbre
- Utilisation de la machine par temps froid
- Entretien
- Introduction
- Calendrier d'entretien
- Entretien et vérifications des dispositifs de sécurité du produit
- Pour vérifier le ruban du frein de chaîne
- Vérifier le protège-main avant et l’activation du frein de chaîne.
- Pour vérifier le frein de chaîne.
- Vérifier le fonctionnement de la gâchette de l’accélérateur et de son dispositif de verrouillage
- Pour vérifier l’attrape-chaîne.
- Pour vérifier le protège-main avant
- Pour vérifier le système antivibrations
- Pour vérifier l’interrupteur de marche/arrêt
- Pour vérifier le silencieux
- Réglage de la vis du régime de ralenti (T)
- Pour examiner si le carburateur est correctement réglé
- Pour remplacer un câble de lanceur rompu ou usé
- Pour serrer le ressort de rappel
- Pour assembler le corps du lanceur sur le produit
- Nettoyage du filtre à air
- Pour vérifier la bougie d’allumage
- Affûter la chaîne.
- Vérification de la lubrification de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Pour effectuer l’entretien du réservoir de carburant et du réservoir d’huile pour chaîne
- Système de nettoyage pneumatique
- Nettoyage du système de refroidissement
- Dépannage
- Transport et entreposage
- Données techniques
- Accessoires
- Garantie
- Blank Page
- Blank Page
- Blank Page
US gallon US fl. oz.
1 2 ½
2 1/2 6 ½
5 12 ⅞
CAUTION: Small errors can influence the
ratio of the mixture drastically when you mix
small quantities of fuel. Measure the quantity
of oil carefully and make sure that you get
the correct mixture.
(Fig. 45)
1. Fill half the quantity of gasoline in a clean container
for fuel.
2. Add the full quantity of oil.
3. Shake the fuel mixture.
4. Add the remaining quantity of gasoline to the
container.
5. Carefully shake the fuel mixture.
CAUTION: Do not mix fuel for more than 1
month at a time.
To fill the fuel tank
1. Clean the area around the fuel tank cap. (Fig. 46)
2. Shake the container and make sure that the fuel is
fully mixed.
3. Remove the fuel tank cap and fill the fuel tank.
4. Tighten the fuel tank cap carefully.
5. Move the product 3 m/10 ft or more away from the
refueling area and fuel source before you start the
engine.
Note:
To see where the fuel tank is on your product,
refer to
Product overview on page 9
.
To do a run-in
• During the first 10 hours of operation, do not apply
full throttle without load for extended periods.
To use the correct chain oil
WARNING:
Do not use waste oil, which can
cause injury to you and the environment.
Waste oil also causes damage to the oil
pump, the guide bar and the saw chain.
WARNING: The saw chain can break if the
lubrication of the cutting equipment is not
sufficient. Risk of serious injury or death to
the operator.
WARNING: This product has a function that
lets the fuel run out before the chain oil. Use
the correct chain oil for this function to
operate correctly. Speak to your servicing
dealer when you select your chain oil.
• Use Husqvarna chain oil for maximum saw chain life
and to prevent negative effects on the environment.
If Husqvarna chain oil is not available, we
recommend you to use a standard chain oil.
• Use a chain oil with good adherence to the saw
chain.
• Use a chain oil with correct viscosity range that
agrees with the air temperature.
CAUTION: If the oil is too thin, it runs out
before the fuel. In temperatures below
0°C/32°F some chain oils become too
thick, which can cause damage to the oil
pump components.
• Use the recommended cutting equipment. Refer to
Accessories on page 28
.
• Remove the cap to the chain oil tank.
• Fill the chain oil tank with chain oil.
• Attach the cap carefully.
(Fig. 47)
Note: To see where the chain oil tank is on you product,
refer to
Product overview on page 9
.
Kickback information
WARNING:
A kickback can cause serious
injury or death to the operator or others. To
decrease the risk you must know the causes
of kickback and how to prevent them.
A kickback occurs when the kickback zone of the guide
bar touches an object. A kickback can occur suddenly
and with large force, which throws the product in the
direction of the operator.
(Fig. 48)
Kickback always occurs in the cutting plane of the guide
bar. Usually, the product is thrown against the operator
but can also move in a different direction. It is how you
use the product when the kickback occurs that causes
the direction of the movement.
(Fig. 49)
A smaller bar tip radius decreases the force of the
kickback.
Use a low kickback saw chain to decrease the effects of
kickback. Do not let the kickback zone touch an object.
WARNING:
No saw chain fully prevents
kickback. Always obey the instructions.
1270 - 002 - 30.06.2020 15