Operating Guide
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- To adjust the idle speed screw (T)
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To do a check of the saw chain lubrication
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- Air cleaning system
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- Warranty
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Introducción
- Para realizar una comprobación de funcionamiento antes de utilizar el producto
- Combustible
- Información de reculada
- Para poner en marcha la máquina
- Para detener la máquina
- Corte de tracción y corte de empuje
- Para utilizar la técnica de corte
- Para utilizar la técnica de desramado
- Para utilizar la técnica de tala
- Para utilizar el producto en climas fríos
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad en el producto
- Para comprobar la cinta de freno
- Para comprobar la protección contra reculadas y la activación del freno de cadena
- Para revisar el freno de cadena
- Para comprobar el acelerador y el bloqueo del acelerador
- Para comprobar el captor de cadena
- Para comprobar la protección de la mano derecha
- Para comprobar el sistema amortiguador de vibraciones
- Para comprobar el interruptor de arranque/detención
- Para comprobar el silenciador
- Para ajustar el tornillo del régimen de ralentí (T)
- Para examinar si el carburador está correctamente ajustado
- Para reemplazar una cuerda de arranque rota o desgastada
- Para apretar el resorte de retorno
- Para montar el cuerpo del mecanismo de arranque en el producto
- Para limpiar el filtro de aire
- Para comprobar la bujía
- Para afilar la cadena de sierra
- Para realizar una comprobación de la lubricación de la cadena de sierra
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Para realizar mantenimiento en el depósito de combustible y en el depósito de aceite para cadena
- Sistema de purificación de aire
- Para limpiar el sistema de refrigeración
- Solución de problemas
- Transporte y almacenamiento
- Datos técnicos
- Accesorios
- Garantía
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Introduction
- Pour vérifier le fonctionnement avant d’utiliser le produit
- Carburant
- Renseignements sur le rebond
- Mise sous tension de l’appareil
- Arrêt de la machine
- Méthode tirée et méthode poussée
- Pour utiliser la technique de coupe
- Pour utiliser la technique d’élagage
- Pour utiliser la technique d’abattage d’arbre
- Utilisation de la machine par temps froid
- Entretien
- Introduction
- Calendrier d'entretien
- Entretien et vérifications des dispositifs de sécurité du produit
- Pour vérifier le ruban du frein de chaîne
- Vérifier le protège-main avant et l’activation du frein de chaîne.
- Pour vérifier le frein de chaîne.
- Vérifier le fonctionnement de la gâchette de l’accélérateur et de son dispositif de verrouillage
- Pour vérifier l’attrape-chaîne.
- Pour vérifier le protège-main avant
- Pour vérifier le système antivibrations
- Pour vérifier l’interrupteur de marche/arrêt
- Pour vérifier le silencieux
- Réglage de la vis du régime de ralenti (T)
- Pour examiner si le carburateur est correctement réglé
- Pour remplacer un câble de lanceur rompu ou usé
- Pour serrer le ressort de rappel
- Pour assembler le corps du lanceur sur le produit
- Nettoyage du filtre à air
- Pour vérifier la bougie d’allumage
- Affûter la chaîne.
- Vérification de la lubrification de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Pour effectuer l’entretien du réservoir de carburant et du réservoir d’huile pour chaîne
- Système de nettoyage pneumatique
- Nettoyage du système de refroidissement
- Dépannage
- Transport et entreposage
- Données techniques
- Accessoires
- Garantie
- Blank Page
- Blank Page
- Blank Page
To sharpen the saw chain
Information about the guide bar and saw chain
WARNING: Use protective gloves when you
use or do maintenance on the saw chain. A
saw chain that does not move can also
cause injuries.
Replace a worn or damaged guide bar or saw chain with
the guide bar and saw chain combination recommended
by Husqvarna. This is necessary to keep the safety
functions of the product. Refer to
Accessories on page
28
, for a list of replacement bar and chain
combinations that we recommend.
• Guide bar length, in/cm. Information about the guide
bar length can usually be found on the rear end of
the guide bar.
(Fig. 111)
• Number of teeth on bar tip sprocket (T).
(Fig. 112)
• Chain pitch, in. The distance between the drive links
of the saw chain must align with the distance of the
teeth on the bar tip sprocket and drive sprocket.
(Fig. 113)
• Number of drive links. The number of drive links is
decided by the type of guide bar.
(Fig. 114)
• Bar groove width, in/mm. The groove width in guide
bar must be the same as the chain drive links width.
(Fig. 115)
• Chain oil hole and hole for chain tensioner. The
guide bar must align with product.
(Fig. 116)
• Drive link width, mm/in.
(Fig. 117)
General information about how to sharpen the
cutters
Do not use a blunt saw chain. If the saw chain is blunt,
you must apply more pressure to push the guide bar
through the wood. If the saw chain is very blunt, there
will be no wood chips but sawdust.
A sharp saw chain eats through the wood and the wood
chips becomes long and thick.
The cutting tooth (A) and the depth gauge (B) together
makes the cutting part of the saw chain, the cutter. The
difference in height between the two gives the cutting
depth (depth gauge setting).
(Fig. 118)
When you sharpen the cutter, think about the following:
• Filing angle.
(Fig. 119)
• Cutting angle.
(Fig. 120)
• File position.
(Fig. 121)
• Round file diameter.
(Fig. 122)
It is not easy to sharpen a saw chain correctly without
the correct equipment. Use Husqvarna file gauge. This
will help you to keep maximum cutting performance and
the kickback risk at a minimum.
WARNING: The force of the kickback
increases a lot if you do not follow the
sharpening instructions.
Note: Refer to
To sharpen the saw chain on page 24
for
information about sharpening of the saw chain.
To sharpen the cutters
1. Use a round file and a file gauge to sharpen the
cutting teeth. (Fig. 123)
Note: Refer to
Accessories on page 28
for
information about which file and gauge that
Husqvarna recommends for your saw chain.
2. Apply the file gauge correctly on to the cutter. Refer
to the instruction supplied with the file gauge.
3. Move the file from the inner side of the cutting teeth
and out. Decrease the pressure on the pull stroke.
(Fig. 124)
4. Remove material from one side of all the cutting
teeth.
5. Turn the product around and remove material on the
other side.
6. Make sure that all cutting teeth are the same length.
General information about how to adjust the
depth gauge setting
The depth gauge setting (C) decreases when you
sharpen the cutting tooth (A). To keep maximum cutting
performance you must remove filing material from the
depth gauge (B) to receive the recommended depth
gauge setting. See
Accessories on page 28
for
instructions about how to receive the correct depth
gauge setting for your saw chain.
(Fig. 125)
WARNING:
The risk of kickback increases if
the depth gauge setting is too large!
To adjust the depth gauge setting
Before you adjust the depth gauge setting or sharpen
the cutters, refer to
To sharpen the cutters on page 24
,
24
1270 - 002 - 30.06.2020