Operating Guide
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard and the chain brake activation
- To do a check of the chain brake
- To do a check of the throttle trigger and throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the right hand guard
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- To adjust the idle speed screw (T)
- To examine if the carburetor is correctly adjusted
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To do a check of the saw chain lubrication
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- Air cleaning system
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- Warranty
- Introducción
- Seguridad
- Montaje
- Funcionamiento
- Introducción
- Para realizar una comprobación de funcionamiento antes de utilizar el producto
- Combustible
- Información de reculada
- Para poner en marcha la máquina
- Para detener la máquina
- Corte de tracción y corte de empuje
- Para utilizar la técnica de corte
- Para utilizar la técnica de desramado
- Para utilizar la técnica de tala
- Para utilizar el producto en climas fríos
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Mantenimiento y comprobaciones de los dispositivos de seguridad en el producto
- Para comprobar la cinta de freno
- Para comprobar la protección contra reculadas y la activación del freno de cadena
- Para revisar el freno de cadena
- Para comprobar el acelerador y el bloqueo del acelerador
- Para comprobar el captor de cadena
- Para comprobar la protección de la mano derecha
- Para comprobar el sistema amortiguador de vibraciones
- Para comprobar el interruptor de arranque/detención
- Para comprobar el silenciador
- Para ajustar el tornillo del régimen de ralentí (T)
- Para examinar si el carburador está correctamente ajustado
- Para reemplazar una cuerda de arranque rota o desgastada
- Para apretar el resorte de retorno
- Para montar el cuerpo del mecanismo de arranque en el producto
- Para limpiar el filtro de aire
- Para comprobar la bujía
- Para afilar la cadena de sierra
- Para realizar una comprobación de la lubricación de la cadena de sierra
- Para examinar el equipo de corte
- Para comprobar la espada guía
- Para realizar mantenimiento en el depósito de combustible y en el depósito de aceite para cadena
- Sistema de purificación de aire
- Para limpiar el sistema de refrigeración
- Solución de problemas
- Transporte y almacenamiento
- Datos técnicos
- Accesorios
- Garantía
- Introduction
- Sécurité
- Montage
- Fonctionnement
- Introduction
- Pour vérifier le fonctionnement avant d’utiliser le produit
- Carburant
- Renseignements sur le rebond
- Mise sous tension de l’appareil
- Arrêt de la machine
- Méthode tirée et méthode poussée
- Pour utiliser la technique de coupe
- Pour utiliser la technique d’élagage
- Pour utiliser la technique d’abattage d’arbre
- Utilisation de la machine par temps froid
- Entretien
- Introduction
- Calendrier d'entretien
- Entretien et vérifications des dispositifs de sécurité du produit
- Pour vérifier le ruban du frein de chaîne
- Vérifier le protège-main avant et l’activation du frein de chaîne.
- Pour vérifier le frein de chaîne.
- Vérifier le fonctionnement de la gâchette de l’accélérateur et de son dispositif de verrouillage
- Pour vérifier l’attrape-chaîne.
- Pour vérifier le protège-main avant
- Pour vérifier le système antivibrations
- Pour vérifier l’interrupteur de marche/arrêt
- Pour vérifier le silencieux
- Réglage de la vis du régime de ralenti (T)
- Pour examiner si le carburateur est correctement réglé
- Pour remplacer un câble de lanceur rompu ou usé
- Pour serrer le ressort de rappel
- Pour assembler le corps du lanceur sur le produit
- Nettoyage du filtre à air
- Pour vérifier la bougie d’allumage
- Affûter la chaîne.
- Vérification de la lubrification de la chaîne
- Pour examiner l’équipement de coupe
- Pour vérifier le guide-chaîne
- Pour effectuer l’entretien du réservoir de carburant et du réservoir d’huile pour chaîne
- Système de nettoyage pneumatique
- Nettoyage du système de refroidissement
- Dépannage
- Transport et entreposage
- Données techniques
- Accessoires
- Garantie
- Blank Page
- Blank Page
- Blank Page
Contents
Introduction..................................................................... 9
Safety............................................................................10
Assembly...................................................................... 13
Operation...................................................................... 14
Maintenance................................................................. 20
Troubleshooting............................................................ 26
Transportation and storage...........................................27
Technical data.............................................................. 27
Accessories.................................................................. 28
Warranty....................................................................... 30
Introduction
Product description
The Husqvarna 435 II, 435e II, 440 II, 440e II are
chainsaw models with a combustion engine.
Work is constantly in progress to increase your safety
and efficiency during operation. Speak to your servicing
dealer for more information.
Intended use
This product is intended for sawing in wood.
Note: National regulations can set limit to the operation
of the product.
Product overview
(Fig. 1)
1. Cylinder cover
2. Air purge bulb
3. Start decal
4. Start/stop switch
5. Rear handle
6. Information and warning decal
7. Fuel tank
8. Adjuster screws carburetor
9. Starter rope handle
10. Starter housing
11. Chain oil tank
12. Product and serial number plate
13. Felling direction mark
14. Front handle
15. Chain brake and front hand guard
16. Muffler
17. Saw chain
18. Bar tip sprocket
19. Guide bar
20. Spiked bumper
21. Chain catcher
22. Chain tensioning screw
23. Clutch cover
24. Right hand guard
25. Throttle trigger
26. Throttle trigger lockout
27. Operator's manual
28. Combination wrench
29. Guide bar cover
Symbols on the product
(Fig. 3) WARNING! Be careful and use the product
correctly. This product can cause serious
injury or death to the operator or others.
(Fig. 4) Read the operator's manual carefully and
make sure that you understand the
instructions before you use this product.
(Fig. 5) Always wear approved protective helmet,
approved hearing protection and eye
protection.
(Fig. 6) Use 2 hands to operate the product.
(Fig. 7) Do not operate the product with one hand
only.
(Fig. 8) Do not let the guide bar tip touch an object.
(Fig. 9) Other approved bar and chain combinations
in the operator's manual.
(Fig. 10) Computed kickback bar stopping angle
without actuated chainbrake, CKA wob.
(Fig. 11) Computed kickback bar stopping angle with
actuated chainbrake, CKA wb.
(Fig. 12) Warning! Kickback can occur when the
guide bar tip touches an object. A kickback
causes a lightning fast reverse reaction that
throws the guide bar up and in the direction
of the operator. Can cause serious injury.
(Fig. 13) Choke.
(Fig. 14) Fuel.
1270 - 002 - 30.06.2020 9