Operator’s manual Manuel d’utilisation Manual de instrucciones 435 435e 440e Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine. Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina. English (7-35) French (36-67) Spanish (68-99) 1153135-49 Rev.
1 3 4 5 6 7 8 9 10 11 12 13 14 16 17 15 2 The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. 1153135-49 Rev.
18 19 20 21 23 24 25 22 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 1153135-49 Rev.
1 42 43 44 45 46 47 48 49 51 52 54 55 50 2 A 1 53 , 56 57 60 61 4 58 59 62 1153135-49 Rev.
63 65 66 1 2 3 64 67 68 70 69 71 72 74 73 75 76 77 78 79 80 81 82 83 84 85 86 1 3 2 1 1 2 87 1153135-49 Rev.
88 90 91 94 95 96 97 98 99 100 101 89 92 102 93 1 103 2 106 104 105 107 108 111 112 109 A B 110 113 6 1153135-49 Rev.
KEY TO SYMBOLS Symbols on the machine and/or in the manual: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • Approved protective helmet • Approved hearing protection • Protective goggles or a visor Switch off the engine before carrying out any checks or maintenance.
KEY TO SYMBOLS You will find the following labels on your chain saw: USA: Canada: 39° EPA III The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. 8 – English 1153135-49 Rev.
CONTENTS Contents KEY TO SYMBOLS Symbols on the machine and/or in the manual: ... CONTENTS Contents ............................................................... INTRODUCTION Dear customer! ..................................................... WHAT IS WHAT? What is what on the chain saw? ........................... GENERAL SAFETY PRECAUTIONS Before using a new chain saw .............................. Important .............................................................. Always use common sense .........
INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.
GENERAL SAFETY PRECAUTIONS Before using a new chain saw • Please read this manual carefully. • (1) - (113) refer to figures on p. 2-6. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping. • Do not use the chain saw until sufficient chain oil has reached the chain. See instructions under the heading Cutting equipment.
GENERAL SAFETY PRECAUTIONS Important IMPORTANT! This chain saw for forest service is designed for forest work such as felling, delimbing and cutting. You should only use the saw with the bar and chain combinations we recommend in the chapter Technical data. Never use the machine if you are fatigued, while under the influence of alcohol or drugs, medication or anything that could affect your vision, alertness, coordination or judgement. Wear personal protective equipment.
GENERAL SAFETY PRECAUTIONS Chain brake and front hand guard Your chain saw is equipped with a chain brake that is designed to stop the chain if you get a kickback. The chain brake reduces the risk of accidents, but only you can prevent them. (3) Take care when using your saw and make sure the kickback zone of the bar never touches any object. (4) • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism.
GENERAL SAFETY PRECAUTIONS Right hand guard ! Apart from protecting your hand if the chain jumps or snaps, the right hand guard stops branches and twigs from interfering with your grip on the rear handle. (11) Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit.
GENERAL SAFETY PRECAUTIONS Bar The smaller the tip radius the lower the chance of kickback. When you sharpen a cutting tooth there are four important factors to remember. 1 Filing angle (19) Chain 2 Cutting angle (20) A chain is made up of a number of links, which are available in standard and low-kickback versions. 3 File position (21) 4 Round file diameter IMPORTANT! No saw chain design eliminates the danger of kickback.
GENERAL SAFETY PRECAUTIONS that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively. • • You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge. Place the depth gauge tool over the chain.
GENERAL SAFETY PRECAUTIONS Checking chain lubrication • Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket. Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface. If the chain lubrication is not working: We recommend you compare the existing chain with a new chain to decide how badly the existing chain is worn.
ASSEMBLY Fitting the bar and chain ! WARNING! Always wear gloves, when working with the chain. 435 Tension the chain by turning the wheel down (+). The chain should be tensioned until it does not sag from the underside of the bar. (32) The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar knob by turning the knob clockwise.
FUEL HANDLING Fuel Two-stroke oil Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.
FUEL HANDLING Fueling ! WARNING! Never use a machine with visible damage to the spark plug guard and ignition cable. A risk of sparking arises, which can cause a fire. Transport and storage ! WARNING! Taking the following precautions, will lessen the risk of fire: • Do not smoke and do not place any hot objects in the vicinity of fuel.
STARTING AND STOPPING Starting and stopping ! WARNING! Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries. Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything.
WORKING TECHNIQUES Before use: (55) 1 Check that the chain brake works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle lockout works correctly and is not damaged. 4 CCheck that the stop switch works correctly and is not damaged. 5 Check that all handles are free from oil. 6 Check that the anti vibration system works and is not damaged. 7 Check that the muffler is securely attached and not damaged.
WORKING TECHNIQUES 4 5 6 7 8 9 log or one piece at a time. Remove the cut pieces to keep your working area safe. (57) Never use the chain saw above shoulder height and avoid cutting with the tip of the bar. Never use the chain saw one-handed! (58) In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support. (59) Always use a fast cutting speed, i.e. full throttle. Take great care when you cut with the top edge of the bar, i.
WORKING TECHNIQUES If it is possible (can you turn the log?) stop cutting about 2/3 of the way through the log. Turn the log and finish the cut from the opposite side. (70) The log is supported at one end. There is a high risk that it will split. (71) The main point to avoid is letting the tree fall onto another tree. It is very dangerous to remove a trapped tree and there is high accident risk. See instructions under the heading Freeing a tree that has fallen badly.
WORKING TECHNIQUES Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter. The uncut section of the trunk is called the felling hinge. The felling hinge controls the direction that the tree falls in. (82) All control over the felling direction is lost if the felling hinge is too narrow or non-existent, or if the directional cuts and felling cut are badly placed.
MAINTENANCE General The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorised service workshop. Carburetor adjustment Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. Checking, maintaining and servicing chain saw safety equipment Note! All servicing and repair work on the machine requires special training.
MAINTENANCE Throttle lockout Muffler • Make sure the throttle control is locked at the idle setting when the throttle lockout is released. (95) Never use a machine that has a faulty muffler. • Press the throttle lockout and make sure it returns to its original position when you release it. (96) • Check that the throttle control and throttle lockout move freely and that the return springs work properly. (97) • Start the chain saw and apply full throttle.
MAINTENANCE Tensioning the recoil spring • Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise. Note! Check that the pulley can be turned at least a further 1/2 turn when the starter cord is pulled all the way out. (104) The filter can be cleaned more thoroughly by washing it in water and detergent. An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals.
MAINTENANCE Cooling system Winter use Running problems can occur when using the machine in the cold and snowy conditions caused by: To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Air guide plate. 3 Fins on the flywheel. 4 Cooling fins on the cylinder. 5 Cylinder cover (directs cold air over the cylinder).
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Weekly maintenance Monthly maintenance Clean the outside of the machine. On chain saws without a catalytic converter, check the cooling system weekly. Check the brake band on the chain brake for wear. Replace when less than 0.6 mm (0,024 inch) remains at the most worn point.
TECHNICAL DATA Technical data 435 435e 440e 2,49/40,9 Engine Cylinder volume, cu.in/cm3 2,49/40,9 2,49/40,9 Cylinder bore, inch/mm 1,61/41 1,61/41 1,61/41 Stroke, inch/mm 1,22/31 1,22/31 1,22/31 Idle speed, rpm 2900 2900 2900 Power, kW/hp @ rpm 1,6/2,2 @ 9000 1,6/2,2 @ 9000 1,8/2,4 @ 9000 125 125 Emissions Durability Period according to California 125 Air Resources Board, h.
TECHNICAL DATA Recommended cutting equipment for Canada Following is a list of recommended cutting equipment for the Husqvarna chain saw models 435, 435e and 440e. The combinations of powerhead, bar and chain meet all requirements outlined in the CSA Z62.1-03 Chainsaws and Z62.304 Chainsaw Kickback standards. The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a solid bar.
FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT IMPORTANT: This product is compliant with U.S. EPA Phase 3 regulations for exhaust and evaporative emissions. To ensure EPA Phase 3 compliance, we recommend using only genuine Husqvarna brand replacement parts. Use of non-compliant replacement parts is a violation of federal law. YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U.S.
FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part. EMISSION WARRANTY PARTS LIST 1 Carburetor and internal parts 2 Intake pipe, airfilter holder and carburetor bolts. 3 Airfilter and fuelfilter covered up to maintenance schedule.
AMERICAN STANDARD SAFETY PRECAUTIONS Safety precautions for chain saw users (ANSI B175.1-2000 Annex C) Kickback safety precautions ! WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction, kicking the guide bar up and back towards the operator.
EXPLICATION DES SYMBOLES Symboles sur la machine et/ou dans le manuel: AVERTISSEMENT! Cette tronçonneuse peut être dangereuse! Une utilisation erronée ou négligente peut occasionner des blessures graves, voire mortelles pour l’utilisateur ou une tierce personne. Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine.
EXPLICATION DES SYMBOLES Remplissage d’huile et réglage du débit d’huile. Le frein de chaîne doit être activé quand la tronçonneuse est démarrée. L’autocollant comportant ce symbol d’avertissement est placé sur la tronçonneuse: 39° EPA III La période de conformité des émissions à laquelle il est fait référence sur l’étiquette de conformité des émissions indique le nombre d’heures de fonctionnement pour lesquelles il a été établi que le moteur répond aux exigences fédérales en matière d’émissions.
SOMMAIRE Sommaire EXPLICATION DES SYMBOLES Symboles sur la machine et/ou dans le manuel: ... SOMMAIRE Sommaire ............................................................. INTRODUCTION Cher client, ............................................................ QUELS SONT LES COMPOSANTS? Quels sont les composants de la tronçonneuse? . INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Mesures à prendre avant de mettre en usage une tronçonneuse neuve ............................................. Important! ...................
INTRODUCTION Cher client, Félicitations pour ce choix d’un produit Husqvarna. Husqvarna a vu le jour en 1689 lorsque le roi Karl XI décida de construire un arsenal pour la fabrication des mousquets au bord de la rivière Huskvarna. Le choix de l’emplacement était logique puisque la rivière Huskvarna servait à produire de l’énergie hydraulique et constituait donc une sorte de centrale hydraulique.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Mesures à prendre avant de mettre en usage une tronçonneuse neuve • Lisez attentivement ce manuel d’utilisation. • (1) - (113) fait référence aux figures des p. 2-6. • Vérifier le montage et le réglage de l’outil de coupe. Voir les instructions au chapitre Montage. • Remplissez de carburant et démarrez la tronçonneuse. Voir les instructions aux chapitres Manipulation du carburant et Démarrage et arrêt.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Important! IMPORTANT! Cette tronçonneuse pour l’administration des forêts est conçue pour des travaux forestiers tels que l’abattage, l’ébranchage et la coupe. Utilisez seulement les combinaisons guide-chaîne/ chaîne recommandées au chapitre Caractéristiques techniques. N’utilisez jamais la machine si vous êtes fatigué, avez bu de l’alcool ou pris des médicaments susceptibles d’affecter votre vue, votre jugement ou la maîtrise de votre corps.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Voir le chapitre Quels sont les composants? pour savoir où se trouvent équipements sur la machine. La durée de vie de la machine risque d'être écourtée et le risque d'accidents accru si la maintenance de la machine n'est pas effectuée correctement et si les mesures d'entretien et/ou de réparation ne sont pas effectuées de manière professionnelle. Pour obtenir de plus amples informations, contacter l'atelier de réparation le plus proche.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ poignée (= quand l’utilisateur tient la poignée), la commande de l’accélération (B) est libérée. Lorsque la poignée est relâchée, la commande de l’accélération et le blocage de l’accélération reviennent à leurs positions initiales. Cette position signifie que la commande d’accélération est alors automatiquement bloquée sur le ralenti.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Règles élémentaires • • • • • N’utiliser que l’équipement de coupe recommandé! Voir les instructions au chapitre Caractéristiques techniques. Veiller à ce que les dents de la chaîne soient toujours bien affûtées! Suivre les instructions et utiliser le gabarit d’affûtage recommandé. Une chaîne émoussée ou endommagée augmente le risque d’accidents.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ ! AVERTISSEMENT! La tendance au rebond augmente considérablement si les instructions d’affûtage ne sont pas respectées. quand vous pouvez passer la lime sur le gabarit sans ressentir de résistance. (25) Tension de la chaîne Affûtage de la dent Pour affûter une dent, une lime ronde et un gabarit d’affûtage sont nécessaires.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Rabattre le bouton pour verrouiller la tension de chaîne. (34) • Vérifier que le canal de graissage du guide-chaîne est bien ouvert. Le nettoyer au besoin. (35) Lubrification de l’équipement de coupe • S’assurer que la gorge du guide est propre. La nettoyer au besoin. (36) • Vérifier que le pignon du nez tourne librement et que l’orifice de graissage est propre. Nettoyer et graisser au besoin.
INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ Contrôle de l’usure de l’équipement de coupe ! Vérifier quotidiennement l’état de la chaîne et s’assurer: • Que les rivets et les maillons ne comportent pas de fissures. • Que la chaîne n’est pas raide. • Que les rivets et les maillons ne sont pas anormalement usés. Jetez la chaîne si un des points ci-dessus est vérifié. Il est recommandé de comparer avec une chaîne neuve pour évaluer le degré d’usure.
MONTAGE Montage du guide-chaîne et de la chaîne ! AVERTISSEMENT! Utiliser des gants pour toute manipulation de la chaîne. 435 S’assurer que le frein de chaîne ne s’est pas déclenché en amenant l’arceau protecteur contre l’étrier de la poignée avant. (39) Dévisser l’écrou du guide-chaîne et retirer le carter d’embrayage (frein de chaîne). Déposer la protection de transport (A). (40) Monter le carter d’embrayage et veillez à placer le goujon de tension de la chaîne dans l’ouverture du guide.
MANIPULATION DU CARBURANT Carburant Remarque! La machine est équipée d’un moteur deux temps et doit toujours être alimentée avec un mélange d’essence et d’huile deux temps. Afin d’assurer un rapport de mélange correct, il est important de mesurer avec précision la quantité d’huile à mélanger. Pour le mélange de petites quantités de carburant, même de petites erreurs au niveau de la quantité d’huile affectent sérieusement le rapport du mélange.
MANIPULATION DU CARBURANT Remplissage de carburant ! 2 Si vous avez renversé du carburant sur vous ou sur vos vêtements, changez de vêtements. Lavez les parties du corps qui ont été en contact avec le carburant. Utilisez de l’eau et du savon. 3 S’il y a fuite de carburant. Vérifier régulièrement que le bouchon du réservoir et la conduite de carburant ne fuient pas.
DÉMARRAGE ET ARRÊT Démarrage et arrêt ! AVERTISSEMENT! Contrôler les points suivants avant la mise en marche: Le frein de chaîne doit être activé lors du démarrage de la tronçonneuse afin de réduire le risque de contact avec la chaîne en rotation. Ne pas démarrer la tronçonneuse si le guide, la chaîne et tous les capots ne sont pas montés. Sinon, l’embrayage risque de se détacher et de causer des blessures personnelles. Placer la machine sur un support stable.
DÉMARRAGE ET ARRÊT • Ne jamais mettre la machine en marche à l’intérieur. Les gaz d’échappement du moteur sont nocifs. • S’assurer que la zone de travail est bien dégagée et qu’aucune personne et aucun animal ne risquent d’entrer en contact avec l’équipement de coupe. • Tenez toujours la tronçonneuse à deux mains. Tenez la main droite sur la poignée arrière et la main gauche sur la poignée avant. Tous les utilisateurs, droitiers et gauchers, doivent la tenir ainsi.
TECHNIQUES DE TRAVAIL Avant chaque utilisation: (55) 1 Contrôler que le frein de chaîne fonctionne correctement et n’est pas endommagé. 2 Contrôler que la protection arrière de la main droite n’est pas endommagée. 3 Contrôler que le blocage de l’accélération fonctionne correctement et n’est pas endommagé. 4 Contrôlez que l’interrupteur d’arrêt fonctionne correctement et est en bon état. 5 Contrôler que toutes les poignées ne comportent pas d’huile.
TECHNIQUES DE TRAVAIL 3 4 5 6 7 8 9 avec les doigts et le pouce. Toujours tenir la tronçonneuse dans cette position, que l’on soit droitier ou gaucher. Une prise solide aide à maîtriser les rebonds et à mieux contrôler la tronçonneuse. Ne pas lâcher les poignées! (56) La plupart des accidents dus à un rebond se produisent lors de l’élagage. Se tenir fermement sur les jambes et s’assurer que la zone de travail est bien dégagée pour ne pas risquer de trébucher ou de perdre l’équilibre.
TECHNIQUES DE TRAVAIL Sciage ! Sens d’abattage AVERTISSEMENT! N’essayez jamais de scier des billes empilées ou serrées les unes contre les autres. Vous augmenteriez considérablement le risque de rebond et de blessures graves et même mortelles. Si vous avez une pile de billes, chaque bille à scier doit être retirée du tas, placée sur un chevalet ou un autre support approprié et être sciée séparément.
TECHNIQUES DE TRAVAIL Solution à un abattage raté Abattage ! AVERTISSEMENT! Il est déconseillé aux utilisateurs non expérimentés d’abattre un arbre dont le diamètre du tronc est supérieur à la longueur du guide-chaîne! L’abattage est constitué de trois entailles. On procède d’abord à l’encoche qui comprend une entaille supérieure et une entaille inférieure, puis à l’abattage proprement dit grâce au trait de chute.
TECHNIQUES DE TRAVAIL Mesures anti-rebond ! AVERTISSEMENT! Un rebond peut-être soudain, rapide et violent et renvoyer la tronçonneuse, le guide-chaîne et la chaîne en direction de l’utilisateur. Si la chaîne est alors en rotation, les blessures encourues sont graves et quelquefois mortelles. Il convient donc de comprendre les raisons d’un rebond afin de pouvoir éviter ce phénomène grâce à une bonne méthode de travail et un comportement prudent.
ENTRETIEN Généralités L’utilisateur ne peut effectuer que les travaux d’entretien et de révision décrits dans ce manuel d’utilisation. Les mesures plus importantes doivent être effectuées dans un atelier d’entretien agréé. Réglage du carburateur Votre produit Husqvarna a été conçu et fabriqué selon des spécifications qui visent à réduire les émissions nocives. Fonctionnement • • Le carburateur détermine le régime du moteur via la commande de l’accélération.
ENTRETIEN Blocage de l’accélération Silencieux • Vérifier d’abord que la commande de l’accélération est bloquée en position de ralenti quand le blocage de l’accélération est en position initiale. (95) Ne jamais utiliser une machine dont le silencieux est défectueux. • Appuyer sur le blocage de l’accélération et vérifier qu’il revient de lui-même en position initiale quand il est relâché.
ENTRETIEN poulie. Monter ensuite le ressort entraîneur, la roue entraîneuse et la vis au centre de la poulie. Passer la corde dans le trou du boîtier du lanceur et dans la poignée du lanceur. Faire un nœud robuste à l’extrémité de la corde. (103) Filtre à air Mise sous tension du ressort Le filtre à air doit être maintenu propre pour éviter: • Placer la corde dans la gorge de la poulie et faire tourner la poulie d’environ deux tours dans le sens des aiguilles d’une montre.
ENTRETIEN Graissage du pignon d’entraînement du guide Lubrifier le pignon du guide à chaque plein d’essence. Utiliser pour cela une burette spéciale et une graisse pour roulement de bonne qualité. (109) Graissage du roulement à aiguilles L’axe de sortie du tambour d’embrayage est doté d’un roulement à aiguilles. Ce roulement à aiguilles doit être graissé régulièrement.
ENTRETIEN Schéma d’entretien La liste ci-dessous indique l’entretien à effectuer sur la machine. La plupart des points sont décrits à la section Entretien. Entretien quotidien Entretien hebdomadaire Entretien mensuel Nettoyer l’extérieur de la machine. Contrôlez chaque semaine le système de refroidissement des tronçonneuses sans pot catalytique. Inspectez le degré d’usure du ruban de freinage du frein de chaîne. Remplacez-le quand les parties les plus usées sont inférieures à 0,6 mm.
CARACTÉRISTIQUES TECHNIQUES Caractéristiques techniques 435 435e 440e Cylindrée, po3/cm3 2,49/40,9 2,49/40,9 2,49/40,9 Alésage, po/mm 1,61/41 1,61/41 1,61/41 Course, po/mm 1,22/31 1,22/31 1,22/31 Régime de ralenti, tr/min 2900 2900 2900 Puissance, kW/hp @ r/min 1,6/2,2 @ 9000 1,6/2,2 @ 9000 1,8/2,4 @ 9000 125 125 Moteur Période de durabilité des émissions selon la commission californienne chargée de la qualité de 125 l'air.
CARACTÉRISTIQUES TECHNIQUES Équipement de coupe recommandé pour Canada Ce qui suit est une liste de combinaisons recommandées pour utilisation sur les tronçonneuses 435, 435e et 440e. Les combinaisons de moteur, guide-chaîne et chaîne ont été élaborées en fonction des normes CSA Z62.1-03 pour tronçonneuses et Z62.3-04 en ce qui concerne I´effet de rebond des tronçonneuses.
DÉCLARATION DE GARANTIE CONTRÔLE DES ÉMISSIONS EN CALIFORNIE ET AU NIVEAU FÉDÉRAL IMPORTANT: Ce produit est conforme à la réglementation de la Phase 3 de l’Agence de Protection de l’Environnement des États-Unis (EPA) en ce qui touche les emissions d’échappement et d’évaporation. Pour assurer la conformité à la Phase 3 de l’EPA, nous recommandons le recours à des pièces de remplacement d’origin Husqvarna uniquement.
DÉCLARATION DE GARANTIE CONTRÔLE DES ÉMISSIONS EN CALIFORNIE ET AU NIVEAU FÉDÉRAL n’est pas supposée être remplacée comme requis dans le calendrier de maintenance est garantie deux (2) ans. Si la pièce tombe en panne durant la période de garantie, elle sera réparée ou remplacée gratuitement par Husqvarna Forest & Garden. Toute pièce réparée ou remplacée durant la période de garantie est garantie pour la période de garantie restante.
PRÉCAUTIONS SÉCURITAIRES CONFORMANT AUX NORMES AMÉRICAINES Consignes de sécurité pour les utilisateurs de tronçonneuses (ANSI B175.1-2000 Annexe C) Précautions à prendre pour se protéger des rebonds ! AVERTISSEMENT! Un rebond peut se produire quand le nez ou l’extrémité du guide heurte un objet ou quand le bois se referme et coince la chaîne dans l’entaille.
ACLARACION DE LOS SIMBOLOS Símbolos en la máquina en/o el manual de instrucciones: ¡ATENCION! ¡Las motosierras pueden ser peligrosas! Su uso descuidado o erróneo puede provocar heridas graves o mortales al operador o terceros. Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina.
ACLARACION DE LOS SIMBOLOS Etiquetas que se encuentran en la motosierra: EPA III El período de cumplimiento de emisiones mencionado en la etiqueta de cumplimiento de emisiones indica el número de horas de funcionamiento en el que el motor ha demostrado cumplir con los requisitos federales en materia de emisiones.
INDICE Índice ACLARACION DE LOS SIMBOLOS Símbolos en la máquina en/o el manual de instrucciones: ........................................................ INDICE Índice .................................................................... INTRODUCCION Apreciado cliente: ................................................. ¿QUE ES QUE? ¿Qué es qué en la motosierra? ............................ INSTRUCCIONES GENERALES DE SEGURIDAD Medidas a tomar antes de utilizar una motosierra nueva .............................
INTRODUCCION Apreciado cliente: ¡Felicidades por haber adquirido un producto Husqvarna! La historia de Husqvarna data del año 1689, cuando el Rey Karl XI encargó la construcción de una fábrica en la ribera del río Huskvarna para la fabricación de mosquetes. La ubicación junto al río Huskvarna era lógica, dado que el río se utilizaba para generar energía hidráulica.
INSTRUCCIONES GENERALES DE SEGURIDAD Medidas a tomar antes de utilizar una motosierra nueva • • • • • • Lea detenidamente el manual de instrucciones. (1) - (113) refiérase a las figuras en p. 2-6. Compruebe el montaje y ajuste del equipo de corte. Vea las instrucciones bajo el título Montaje. Ponga combustible y arranque la motosierra. Vea las instrucciones en los capítulos Manipulación del combustible y Arranque y parada.
INSTRUCCIONES GENERALES DE SEGURIDAD Emplee siempre el sentido común (2) Equipo de seguridad de la máquina Es imposible abarcar todas las situaciones imaginables que se pueden producir al utilizar una motosierra. Proceda con cuidado y emplee el sentido común. Evite todo uso para el cual no se sienta suficientemente calificado. Si después de leer estas instrucciones todavía se siente inseguro en cuanto al procedimiento de uso, consulte con un experto antes de proseguir.
INSTRUCCIONES GENERALES DE SEGURIDAD sierra en movimiento. No deje la motosierra conectada con el freno de cadena activado por mucho tiempo. La motosierra puede alcanzar una temperatura muy alta. ¿Se activa siempre por inercia el freno de cadena cuando se produce una reculada? • Para liberar el freno de cadena, mueva hacia atrás (en dirección a la empuñadura del mango) la protección contra reculadas con la inscripción «TIRAR HACIA ATRÁS PARA REINICIAR».
INSTRUCCIONES GENERALES DE SEGURIDAD Sistema amortiguador de vibraciones ¡NOTA! El silenciador está muy caliente durante el funcionamiento y después de parar. Esto también es aplicable al funcionamiento en ralentí. Preste atención al riesgo de incendio, especialmente al emplear la máquina cerca de sustancias y/o gases inflamables. Su máquina incorpora un sistema amortiguador diseñado para reducir al máximo posible las vibraciones y optimizar la comodidad de uso.
INSTRUCCIONES GENERALES DE SEGURIDAD Equipo de corte reductor de reculadas ! ¡ATENCION! Un equipo de corte defectuoso o una combinación errónea de espada/cadena de sierre aumentan el riesgo de reculadas. Utilice solamente las combinaciones de espada/cadena de sierra recomendadas y siga las instrucciones. Vea las instrucciones bajo el titular Datos técnicos Las reculadas sólo puede evitarlas Ud. el usuario, impidiendo que el sector de riesgo de reculada de la espada toque algún objeto.
INSTRUCCIONES GENERALES DE SEGURIDAD Afilado de dientes cortantes Tensado de la cadena Para afilar dientes de corte se requiere una lima redonda y un calibrador de afilado. Vea las instrucciones del capítulo Datos técnicos en lo referente al diámetro de fila redonda y el calibrador de afilado recomendados para la cadena de su motosierra. • • • Compruebe que la cadena esté bien tensada. Con un tensado insificiente, la cadena tiene inestabilidad lateral, lo cual dificulta el afilado correcto.
INSTRUCCIONES GENERALES DE SEGURIDAD Lubricación del equipo de corte ! ¡ATENCION! La lubricación insuficiente del equipo de corte puede ocasionar roturas de cadena, con el riesgo consiguiente de accidentes graves e incluso mortales. Si no funciona la lubricación de la cadena: • Compruebe que el canal de aceite de cadena en la espada esté abierto. Límpielo si es necesario. (35) • Compruebe que la guía de la espada esté limpia. Límpiela si es necesario.
INSTRUCCIONES GENERALES DE SEGURIDAD Espada Controle a intervalos regulares: • Si se han formado rebabas en los lados de la espada. Lime si es necesario. • Si la guía de la espada presenta un desgaste anormal. Cambie la espada si es necesario. • Si la punta de la espada presenta un desgaste anormal o irregular. Si se ha formado una ”cavidad” al final del radio de la punta, en la parte inferior de la espada, es señal de que Ud. ha utilizado la máquina con un tensado de cadena insuficiente.
MONTAJE Montaje de la espada y la cadena ! ¡ATENCION! Para manipular la cadena deben utilizarse guantes protectores. 435 Compruebe que no esté activado el freno de cadena empujando la protección contra reculadas del freno de cadena hacia el mango delantero. (39) Desenrosque la tuerca de la espada y desmonte la carcasa del embrague (el freno de cadena). Saque la protección de transporte (A). (40) Monte la espada sobre el perno de la espada. Coloque la espada en la posición posterior extrema.
MANIPULACION DEL COMBUSTIBLE Carburante Mezcla Aclaración! La máquina tiene motor de dos tiempos, por lo que debe utilizarse siempre una mezcla de gasolina con aceite para motores de 2 tiempos. Es importante medir con precisión la cantidad de aceite que se mezcla para conseguir la proporción de mezcla adecuada. Al mezclar pequeñas cantidades de combustible, incluso los pequeños errores en la cantidad de aceite tienen una gran incidencia en la proporción de mezcla. 1:50 (2%) para todos los motores.
MANIPULACION DEL COMBUSTIBLE Repostaje ! 2 Si se salpicó el cuerpo o las ropas, cambie de ropas. Lave las partes del cuerpo que han entrado en contacto con el combustible. Use agua y jabón. 3 Si hay fugas de combustible en la máquina. Compruebe regularmente si hay fugas en la tapa del depósito o en los conductos de combustible. ¡ATENCION! Las siguientes medidas preventivas reducen el riesgo de incendio: ! No fume ni ponga objetos calientes cerca del combustible.
ARRANQUE Y PARADA Arranque y parada ! Motor caliente ¡ATENCION! Antes de arrancar, observe lo siguiente: Posición de arranque, 1: Para la función combinada de estrangulamiento/aceleración de arranque en caliente, mueva el estrangulador tirando del mando rojo hacia fuera y hacia arriba. El freno de cadena debe estar aplicado cuando se arranca la motosierra, para reducir el riesgo de contacto con la cadena en movimiento al ponerse en marcha.
ARRANQUE Y PARADA capítulo Arranque y parada. No arranque nunca la motosierra agarrando el cordón de arranque y soltando la máquina. Este método es muy peligroso porque se pierde fácilmente el control de la motosierra. (52) • No ponga nunca en marcha la máquina en interiores. Tenga en cuenta el riesgo de inhalación de los gases de escape del motor. • Observe el entorno y asegúrese de que no haya riesgo de tocar a personas o animales con el equipo de corte.
TECNICA DE TRABAJO Antes de utilizar la máquina: (55) 1 Compruebe que el freno de cadena funcione correctamente y no esté dañado. 2 Compruebe que la protección trasera de la mano derecha no esté dañada. 3 Compruebe que el fiador contra aceleraciones involuntarias funcione correctamente y no esté dañado. 4 Compruebe que el botón de parada funciona bien y está en buen estado. 5 Compruebe que todos los mangos estén libres de aceite.
TECNICA DE TRABAJO reculada y, al mismo tiempo, mantener el control de la motosierra. ¡No suelte los mangos! (56) 3 La mayoría de los accidentes por reculada se producen al desramar. Procure trabajar con una postura estable y que en el suelo no hayan objetos que puedan hacerle tropezar y perder el equilibrio. Si se trabaja con negligencia, el sector de riesgo de reculada de la espada puede tocar involuntariamente una rama, un árbol u otro objeto y producir una reculada. Controle la pieza de trabajo.
TECNICA DE TRABAJO Desramado Técnica de tala Para cortar ramas gruesas deben aplicarse los mismos principios que para el tronzado. ¡IMPORTANTE! La tala de árboles requiere mucha experiencia. Un usuario de motosierra inexperto no debe talar árboles. ¡Evite los trabajos para los que no se considere suficientemente capacitado! Corte las ramas difíciles por partes. (66) Tronzado ! ¡ATENCION! No intente nunca serrar troncos apilados ni dos troncos que están muy juntos.
TECNICA DE TRABAJO Corte de ramas bajas y camino de retirada Desrame el ronco hasta la altura del hombro. Es más seguro trabajar de arriba a abajo y tener el tronco entre usted y la motosierra. (77) Limpie la vegetación que hay alrededor del árbol y elimine los eventuales obstáculos (piedras, ramas, huecos, etc.) para tener preparado un camino de retirada cuando empiece a caer el árbol. El camino de retirada debe estar a unos 135°, oblicuamente hacia atrás, de la dirección de derribo prevista.
TECNICA DE TRABAJO Medidas preventivas de las reculadas ! ¡ATENCION! Las reculadas pueden ser rapidísimas, repentinas y violentas, lanzando la motosierra, la espada y la cadena contra el usuario. Si la cadena en movimiento toca al usuario, pueden producirse lesiones muy graves e incluso mortales. Es necesario comprender las causas de las reculadas y que pueden evitarse procediendo con cuidado y trabajando con la técnica correcta.
MANTENIMIENTO Generalidades El usuario sólo puede efectuar los trabajos de mantenimiento y servicio descritos en este manual. Los trabajos de mayor envergadura debe efectuarlos un taller de servicio oficial. Ajuste del carburador Su producto Husqvarna ha sido construido y fabricado conforme a especificaciones que reducen los gases de escape tóxicos.
MANTENIMIENTO Fiador del acelerador Silenciador • Nunca utilice una máquina que tenga un silenciador defectuoso. • • • Compruebe que el acelerador esté bloqueado en la posición de ralentí cuando el fiador está en su posición inicial. (95) Apriete el fiador del acelerador y compruebe que vuelva a su posición de partida al soltarlo. (96) Compruebe que el acelerador y el fiador se muevan con facilidad y que funcionen sus muelles de retorno. (97) Arranque la motosierra y acelere al máximo.
MANTENIMIENTO arrastre y el tornillo en el centro de la polea. Inserte el cordón de arranque en el agujero de la caja del mecanismo de arranque y en la empuñadura de arranque. A continuación haga un nudo resistente en el cordón de arranque. (103) Tensado del muelle de retorno • Saque el cordón de arranque de la guía de la polea y gire ésta en el sentido de las agujas del reloj unas 2 vueltas. Aclaración! Compruebe que sea posible girar la polea como mínimo 1/2 vuelta más con el cordón totalmente extraído.
MANTENIMIENTO Engrase del cabezal de rueda de la espada El cabezal de rueda de la espada debe engrasarse en cada repostaje. Utilice la pistola de engrase especial y grasa para cojinetes de buena calidad. (109) Lubricación del cojinete de agujas Depuración centrífuga ”Air Injection” Con la depuración centrífuga, todo el aire que va al carburador entra (es absorbido) a través del mecanismo de arranque. El ventilador de enfriamiento evacúa centrífugamente la suciedad y el polvo.
MANTENIMIENTO Programa de mantenimiento A continuación incluimos una lista con los puntos de mantenimiento a efectuar en la máquina. La mayoría de los puntos se describen en el capítulo “Mantenimiento”. Mantenimiento diario Mantenimiento semanal Mantenimiento mensual Limpie la parte exterior de la máquina. En motosierras sin catalizador, controle el sistema de refrigeracón semanalmente. Compruebe si está desgastada la cinta del freno de cadena.
DATOS TECNICOS Datos técnicos 435 435e 440e Cilindrada, pulgadas/cm3 2,49/40,9 2,49/40,9 2,49/40,9 Diámetro del cilindro, pulgadas/mm 1,61/41 1,61/41 1,61/41 Carrera, pulgadas/mm 1,22/31 1,22/31 1,22/31 Régimen de ralentí, rpm 2900 2900 2900 Potencia, kW/rpm 1,6/2,2 @ 9000 1,6/2,2 @ 9000 1,8 / 2,4 @ 9000 125 125 Motor Período de durabilidad de las emisiones según la Junta 125 de Recursos del Aire de California.
DATOS TECNICOS Combinaciones aprobadas de espada y cadena originales y de repuesto A continuación se presenta una lista de los equipos de corte recomendados para los modelos de motosierras Husqvarna 435, 435e y 440e. Las combinaciones de cabezal de fuerza, espada y cadena han sido probadas y se ha verificado que cumplen con los requisitos de reculada y vibraciones de ANSI B175.1–2000.
DECLARACIÓN DE GARANTÍA DE CONTROL DE EMISIONES FEDERAL Y CALIFORNIANA IMPORTANTE: Este producto es conforme con la normativa Fase 3 de la Agenicia de Protección Ambiental de los Estados Unidos (EPA) referente a emisiones de escape y evaporación. Para asegurar la conformidad con EPA fase 3, se recomienda utilizar sólo repuestos originales de la marca Husqvarna. El uso de otro tipo de repuestos incumple las leyes federales. SUS DERECHOS Y OBLIGACIONES DE GARANTIA La EPA de los EE. UU.
DECLARACIÓN DE GARANTÍA DE CONTROL DE EMISIONES FEDERAL Y CALIFORNIANA regulares según el programa de mantenimiento tendrá una garantía de dos años. Una declaración contenida en las instrucciones según la cual la pieza se deba «reparar o cambiar cuando sea necesario» no reducirá el período de garantía. Cualquier pieza que se repare o cambie en el periodo de garantía seguirá cubierta por la garantía durante el periodo de tiempo restante.
PRECAUCIONES DE SEGURIDAD DE LA NORMA AMERICANA Precauciones de seguridad para usuarios de motosierras (ANSI B175.1-2000 Anexo C) Precauciones de seguridad en reculadas ! ATENCIÓN! La reculada se puede producir cuando la punta de la espada toca en un objeto o cuando la madera se cierra y agarra la cadena de la motosierra en el corte. En algunos casos el contacto de la punta de la espada puede causar una reacción de inversión rapidísima que hace rebotar la espada hacia arriba y atrás hacia el operador.
Original instructions Instructions d’origine Instrucciones originales 1153135-49 ´®z+U-V¶9c¨ ´®z+U-V¶9c¨ 2013-12-09, Rev.