Operator's Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- To remove the product from the carton
- Loose parts
- Tools required
- To install the handle
- To install the discharge chute
- To install the discharge chute lever and the release cable
- To install the remote control for the discharge chute deflector
- To install the speed control cable
- To install the battery ground cable
- To attach replacement shear pins
- Operation
- Before you start the product
- To fill the engine with oil
- To fill fuel
- To start the engine, manual start
- To start the engine, electric start
- To operate the product
- Throttle control
- To use the throttle control
- To use the heated handles
- To stop the product
- To adjust the discharge chute and the discharge chute deflector
- To adjust the skid plates
- To use the drift cutters (if equipped)
- To adjust the height of the auger bucket (for ST 424T/427T/430T only)
- To prevent freeze-up after use
- To get a good result
- Maintenance
- Introduction
- Maintenance schedule
- To do a general inspection
- Oil change reminder
- To reset the oil change reminder
- To do a check of the oil level
- To replace the engine oil
- To lubricate the product
- Battery
- Muffler
- To examine the spark plug
- To inspect the augers and the scraper bar
- To replace the auger shear pins
- To replace the impeller shear pins
- To replace the fuse
- To examine the tires
- To clear a clogged discharge chute deflector
- To replace the scraper bar
- Drive belts
- To prepare for replacement of the belts
- To remove the drive belt
- To install the drive belt
- To install the belt cover
- To adjust the drive belt tension
- To remove the auger belt (for ST 427/430 only)
- To remove the auger belt (for ST 424T/427T/430T only)
- To install the auger belt
- To adjust the auger belt tension
- To adjust the auger control cable
- To adjust the release cable of the discharge chute
- To adjust the left and right discharge chute cables
- To remove the wheels
- To adjust the tension of the continuous tracks (for ST 424T/427T/430T only)
- To clean the product
- Troubleshooting
- Transportation, storage and disposal
- Technical data
- Contenido
- Introducción
- Seguridad
- Montaje
- Para extraer el producto de la caja de cartón
- Piezas sueltas
- Herramientas necesarias
- Para instalar la empuñadura
- Instalación del conducto de expulsión
- Instalación de la palanca del conducto de expulsión y el cable de liberación
- Instalación del control remoto para el conducto de expulsión del deflector
- Instalación del cable de control de velocidad
- Para instalar el cable de conexión a tierra de la batería
- Fijación de los pasadores de deslizamiento de recambio
- Funcionamiento
- Antes de arrancar el producto
- Para llenar el motor con aceite:
- Para agregar combustible
- Para arrancar el motor con arranque manual
- Para arrancar el motor con arranque eléctrico
- Para hacer funcionar el producto
- Control del acelerador
- Para utilizar el control del acelerador
- Uso de los mangos térmicos
- Para detener la máquina
- Ajuste del conducto de expulsión y de su deflector
- Para ajustar las planchas protectoras:
- Para utilizar las cortadoras de deriva (si están equipadas)
- Ajuste de la altura de la tolva sinfín (solo para ST 424T/427T/430T )
- Para evitar el congelamiento después de su uso
- Para conseguir un buen resultado
- Mantenimiento
- Introducción
- Programa de mantenimiento
- Para hacer una inspección general
- Recordatorio de cambio de aceite
- Restablecimiento del recordatorio de cambio de aceite
- Para comprobar el nivel de aceite
- Para cambiar el aceite del motor:
- Para lubricar el producto
- Batería
- Silenciador
- Para examinar la bujía
- Para inspeccionar los barrenos y la espada del raspador:
- Para reemplazar los pasadores fusibles del barreno
- Para reemplazar los pasadores fusibles del propulsor
- Para reemplazar el fusible
- Para examinar los neumáticos
- Eliminación de obstrucciones del deflector del conducto de expulsión:
- Para reemplazar la espada del raspador
- Correas de transmisión
- Para preparar el reemplazo de las correas
- Para retirar la correa de transmisión
- Para instalar la correa de transmisión
- Para instalar la cubierta de la correa
- Ajuste de la tensión de la correa de transmisión
- Retiro de la correa del barreno (solo para ST 427/430 )
- Retiro de la correa del barreno (solo para ST 424T/427T/430T )
- Para instalar la correa del barreno
- Ajuste de la tensión de la correa del barreno
- Para ajustar el cable de control del barreno
- Ajuste del cable de liberación del conducto de expulsión
- Ajuste de los cables del conducto de expulsión de la izquierda y derecha
- Para quitar las ruedas
- Ajuste de la tensión de la banda continua (solo para ST 424T/427T/430T )
- Para limpiar el producto
- Solución de problemas
- Transporte, almacenamiento y eliminación de residuos
- Datos técnicos
- Table des matières
- Introduction
- Sécurité
- Montage
- Retrait du produit du carton
- Pièces libres
- Outils nécessaires
- Installation de la poignée
- Installation de la goulotte d'éjection
- Installation du levier de la goulotte d’éjection et du câble de déverrouillage
- Installation de la commande à distance du déflecteur de la goulotte d'éjection
- Installation du câble de commande de vitesse
- Pour installer le câble de masse de la batterie
- Fixation des goupilles de tonte de rechange
- Fonctionnement
- Avant de démarrer le produit
- Remplissage du moteur avec de l’huile
- Faire le plein
- Démarrage du moteur (manuel)
- Démarrage du moteur (électrique)
- Utilisation de la machine
- Commande d’accélérateur
- Utilisation de la commande d’accélérateur
- Utilisation des poignées chauffantes
- Arrêt de la machine
- Réglage de la goulotte d’éjection et du déflecteur de la goulotte d'éjection
- Réglage des plaques de protection
- Utilisation des coupe-bancs (selon équipement)
- Réglage de la hauteur du godet à tarière (pour ST 424T/427T/430T uniquement)
- Prévention du gel après utilisation
- Pour obtenir un bon résultat
- Entretien
- Introduction
- Calendrier d'entretien
- Pour effectuer une inspection générale
- Rappel de changement d'huile
- Réinitialisation du rappel de changement d'huile
- Vérification du niveau d’huile
- Vidange de l’huile
- Lubrification de la machine
- Batterie
- Silencieux
- Vérification de la bougie d’allumage
- Inspection des tarières et de la barre de racleur
- Remplacement des goupilles de tonte de la tarière
- Remplacement des goupilles de tonte de la roue à ailette
- Remplacement du fusible principal
- Pour examiner les pneus
- Dégagement d’un déflecteur de goulotte d'éjection bouché
- Remplacement de la barre de racleur
- Courroies d’entraînement
- Préparation du remplacement des courroies
- Retrait de la courroie d’entraînement
- Installation de la courroie d’entraînement
- Installation du carter de la courroie
- Réglage de la tension de la courroie d’entraînement
- Retrait de la courroie de la tarière (pour ST 427/430 uniquement)
- Retrait de la courroie de la tarière (pour ST 424T/427T/430T uniquement)
- Installation de la courroie de tarière
- Réglage de la tension de la courroie de la tarière
- Ajustement du câble de commande de la tarière
- Réglage du câble de déverrouillage de la goulotte d'éjection
- Réglage des câbles gauche et droit de la goulotte d'éjection
- Dépose des roues
- Réglage de la tension des chenilles continues (pour ST 424T/427T/430T uniquement)
- Pour nettoyer l’outil
- Dépannage
- Transport, entreposage et mise au rebut
- Caractéristiques techniques
• When you use this product the engine makes an
electromagnetic field. The electromagnetic field
can cause damage to medical implants. Speak to
your physician and medical implant manufacturer
before you operate the product.
• Do not let a child operate the product. Do not let
a person, without knowledge of the instructions
operate the product.
• Make sure that you always monitor a person,
with decreased physical capacity or mental
capacity, that uses the product. A responsible
adult must be there at all times.
• Lock the product in an area that children and
unapproved persons cannot access.
• The product can eject objects and cause injuries.
Obey the safety instructions to decrease the risk
of injury or death.
• Do not go away from the product when the
engine is on.
• The operator of the product is responsible if an
accident occurs.
• Before and while you walk rearward, look behind
and down for small children, animals or other
risks that can cause you to fall.
• Make sure that parts are not damaged before
you use the product.
• Make sure that you are at a minimum 15 m (50
ft) away from other persons or animals before
you use the product. Make sure that a person in
adjacent area knows that you will use the
product.
• Refer to national or local laws. They can prevent
or decrease the operation of the product in some
conditions.
Safety instructions for operation
• Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all
times.
• Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert
for hidden hazards or traffic.
• After striking a foreign object, stop the engine
(motor), remove the wire from the spark plug,
disconnect the cord on electric motors,
thoroughly inspect the product for any damage,
and repair the damage before restarting and
operating the product.
• If the product starts to vibrate abnormally, stop
the engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
• Stop the engine (motor) whenever you leave the
operating position, before unclogging the auger
housing or chute deflector, and when making any
repairs, adjustments or inspections.
• When cleaning, repairing or inspecting the
product, stop the engine and make certain the
augers and all moving parts have stopped.
Disconnect the spark plug wire and keep the wire
away from the plug to prevent someone from
accidentally starting the engine.
• Do not run the engine indoors, except when
starting the engine and for transporting the
product in or out of the building. Open the
outside doors; exhaust fumes are dangerous.
• Exercise extreme caution when operating on
slopes.
• Never operate the product without proper guards,
and other safety protective devices in place and
working.
• Never direct the chute deflector toward people or
areas where property damage can occur. Keep
children and others away.
• Do not overload the product capacity by
attempting to clear snow at too fast a rate.
• Never operate the product at high transport
speeds on slippery surfaces. Look behind and
use care when operating in reverse.
• Disengage power to the augers when the product
is transported or not in use.
• Use only attachments and accessories approved
by the manufacturer of the product (such as
wheel weights, counterweights, or cabs).
• Never operate the product without good visibility
or light. Always be sure of your footing, and keep
a firm hold on the handles. Walk; never run.
• Never touch a hot engine or muffler.
Work area safety
• Thoroughly inspect the area where the
equipment is to be used and remove all
doormats, sleds, boards, wires, and other foreign
objects.
• Disengage all clutches and shift into neutral
before starting the engine (motor).
• Do not operate the product without wearing
adequate winter garments. Avoid loose fitting
clothing that can get caught in moving parts.
Wear footwear that will improve footing on
slippery surfaces.
• Handle fuel with care; it is highly flammable.
• Use an approved fuel container.
• Never add fuel to a running engine or hot
engine.
• Fill fuel tank outdoors with extreme care.
Never fill fuel tank indoors.
• Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground, away from
your vehicle, before filling.
• When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times,
until refueling is complete. Do not use a
nozzle lock-open device.
876 - 014 - 19.05.2021
7