USER MANUAL BREEZE QC 520, QC 620, QC 720
Fläkten är tillverkad i moduler så att endast små detaljer behöver bytas vid eventuell service. Ventilatoren er bygget opp av moduler slik at det kun er nødvendig å bytte små detaljer ved eventuelt behov for service. Emhætten er frem stillet i moduler, så de enkelte del kan udskiftes ved hætter evt. service. SERVICE Liesituuletin on moduulirakenteinen siten, että huollon yhteydessä pitää vaihtaa vain pieniä osia. Built in modules so that only small parts need replacing at service.
Contents Safety instructions .................................................... 31 Description of the cooker hood ................................ 32 Using the cooker hood .............................................. 33 Maintenance and cleaning ........................................ 33 If the hood does not function .................................... 34 Technical data ........................................................... 35 Installation ..........................................................
Description of the cooker hood The cooker hood Work light Duct Motorhouse Grease filter Control panel Accessories Functions The following are included with the cooker hood: Template for mounting: Template for mounting on wall and under cupboard (printed on packaging).
Using the cooker hood The control panel Do not operate the fan at a higher speed than necessary. The low speeds are adequate for ordinary requirements while cooking. The high speeds should be used only if food has burnt while cooking, or for other strong fumes. The control panel is under the cooker hood. Best results are obtained by using low speed for normal conditions and high speed when smells and steam are more concentrated. On and Off switch. Speed adjustment switch.
Cleaning the motor cover It is also possible to clean the motor cover (Fig. 2): Remove the grease filter. Remove the inlet ring (A) by turning it anticlockwise. Remove the fan wheel by unscrewing the centre nut (B) on the fan wheel. Use gloves when removing the fan wheel. Clean all the plastic and metal parts with warm water and washing dergent. Replace in reverse order. Changing the light B A Fig. 2 Turn off the power before changing the light.
Technical data Model Airflow Size Light Grease filter Voltage Total power Max. Min. Height Width Depth QC 520 QC 620 QC 720 320 m ³/h x) 180 m ³/h 160 m ³/h 45 mm 498 mm 445 mm Max 11 W PL 1 pc. 230 V 111 W 320 m ³/h x) 180 m ³/h 160 m ³/h 45 mm 598 mm 445 mm Max 11 W PL 1 pc. 230 V 111 W 320 m ³/h x) 180 m ³/h 160 m ³/h 45 mm 698 mm 445 mm Max 11 W PL 1 pc. 230 V 111 W x) Valid when the cooker hood is fitted with carbon filter. 45 5 46 498 / 598 / 698 Fig.
Mounting of cooker hood in a cupboard, Alt. 1 (Fig. 6): Cut an opening and drill 4 holes in the underside of the cupboard. Use the template printed on the packaging. Mount the locknuts (A) on the cooker hood. Mount the cooker hood with four screws (B) and washers (C). B A C 1 2 Fig. 6 Mounting of cooker hood in a cupboard, Alt. 2 (Fig. 7): Cut an opening in the underside of the cupboard. Use the template printed on the packaging. Mount the cooker hood with two screws (A) and the spacers (B).
Mounting the cold air valve (Fig. 10): Not applicable for recirculation. The cold air valve consists of a damper seat with two valves, which shall be fitted into the hood outlet. If there is no other form of ventilation to expel air from the kitchen than the hood, the outer end of the valves should be clipped off and removed. Insert a pen or something similar between the valves. These should open up easily now. A B C Fig. 10 Extend the duct hose correctly.
821 27 45-02/2 ©1998 MO-STF