Operator’s manual (EPA) 326RJX Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
KEY TO SYMBOLS Symbols Only intended for trimmer heads. WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Other symbols/decals on the machine refer to special certification requirements for certain markets.
CONTENTS Contents KEY TO SYMBOLS Symbols ........................................................................ CONTENTS Contents ....................................................................... Note the following before starting: ................................. SAFETY INSTRUCTIONS Personal protective equipment ...................................... Machine′s safety equipment ......................................... Checking, maintaining and servicing the machine′s safety equipment .............
SAFETY INSTRUCTIONS Personal protective equipment FIRST AID KIT Always have a first aid kit nearby. IMPORTANT! Whenever you use a clearing saw, brushcutter or trimmer you must wear personal protective equipment that is approved by the authorities. Personal protective equipment does not eliminate the risk of accidents, but it can reduce the effects of an injury in the event of an accident. Ask your dealer for help when choosing protective equipment.
SAFETY INSTRUCTIONS ! WARNING! Never use a cutting attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury. Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. For mufflers it is very important that you follow the instructions on checking, maintaining and servicing your machine.
SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine′s safety equipment IMPORTANT! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service.
SAFETY INSTRUCTIONS • • Regularly check that the muffler is securely attached to the machine. Locking nut • When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.) • Tighten the nut using the socket spanner. 35-50 Nm (3.55 kpm).
SAFETY INSTRUCTIONS Cutting equipment • The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter. IMPORTANT! • This section describes how to choose and maintain your cutting equipment in order to: Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.
SAFETY INSTRUCTIONS General safety precautions • IMPORTANT! The machine is only designed for trimming grass, grass clearing and/or forestry clearing. Place the machine on the ground, ensure the cutting attachment is clear of twigs and stones. Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot). Then grip the starter handle with your right hand and pull the starter cord.
SAFETY INSTRUCTIONS • The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. ! WARNING! Take care when handling fuel. Bear in mind the risk of fire, explosion and inhaling fumes. Basic working techniques • Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Terms • Use a grass cutter or grass blade for clearing grass.
SAFETY INSTRUCTIONS Grass trimming using a trimmer head and plastic blades • Trimming Do not allow the trimmer head to constantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head. Sweeping • • • Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut.
WHAT IS WHAT? 29 28 27 ¢ = What is what on the trimmer? 1 Trimmer head 16 Handle adjustment 2 Grease filler cap 17 Locking nut 3 Bevel gear 18 Support flange 4 Cutting attachment guard 19 Drive disc 5 Shaft 20 Socket spanner 6 Loop handle 21 Operator’s manual (EPA) 7 Throttle control 22 Allen key 8 Stop switch 23 Locking pin 9 Throttle lock 24 Support cup 10 Cylinder cover 25 Blade 11 Starter handle 26 Transport guard 12 Fuel tank 27 J-handle 13 Choke control 28 Suppor
ASSEMBLY Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. Fitting a trimmer guard and Superauto II trimmer head K G F I K J • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Attach the J-handle to the loop handle using the three screws, as shown. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob.
ASSEMBLY Fitting the blade guard/combination guard, grass blade and grass cutter Fitting other guards and cutting attachments • • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CAUTION! Use the recommended blade guard. See the Technical data section. Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L).
FUEL HANDLING Fuel Mixing CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. • Always mix the gasoline and oil in a clean container intended for fuel.
STARTING AND STOPPING Check before starting Starting and stopping For safety reasons follow these recommendations! • • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.
STARTING AND STOPPING Air purge: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Stopping Stop the engine by switching off the ignition. ! WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately. Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!).
MAINTENANCE Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, ask your dealer/service workshop (who will have a rev counter at their disposal) to adjust your carburettor.
MAINTENANCE will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. Correctly adjusted carburettor When the carburettor is correctly adjusted the machine will accelerate without hesitation and burble a little at maximum speed. It is also important that the cutting attachment does not rotate at idle. If the low speed jet L is set too lean it may cause starting difficulties and poor acceleration.
MAINTENANCE Cooling system Air filter To keep the working temperature as low as possible the machine is equipped with a cooling system. The air filter must be regularly cleaned to remove dust and dirt in order to avoid: The cooling system consists of: • Carburettor malfunctions • Starting problems 3 • Loss of engine power 2 • Unnecessary wear to engine parts • Excessive fuel consumption. 4 1 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder.
MAINTENANCE Bevel gear Weekly maintenance • Check the starter and starter cord. • Clean the carburettor area. The bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. • Clean the outside of the spark plug. Remove it and check the electrode gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug.
TECHNICAL DATA Technical data 325RJ-X Engine Cylinder volume, cu.in/cm3 1,50/24,5 Cylinder bore, inch/mm 1,34/34,0 Stroke, inch/mm 1,06/27 Idle speed, rpm 2700 Recommended max. speed, rpm 11000-11700 Speed of output shaft, rpm 8014 Max. engine output, acc.
FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards.
Super Auto II Super Auto II 1" 1 2 3 4 2,4 mm .
Trimmy H II 1 2 3 4 2,0-2,4 mm .080-.
Trimmy Hit 2 3 2,0-2,4 mm .080-.
Trimmy Hit Pro 2 3 2,0-2,4 mm .080-.095" 1 7,5 m 25' 4 15 cm 6" ~ 3,7 m 12' 5 6 7 9 8 15 cm 6" 11 10 12 1.) 2.
T35 2 3 2,4-2,7 mm .095-.
S35 2 3 2,4-2,7 mm .095-.
S35 3 2 2,4-2,7 mm .095-.
1140244-95 ´®z+H8Q¶5(¨ ´®z+H8Q¶5(¨ 2003-11-18