User manual
Table Of Contents
- Symbols on the machine:
- Symbols in the operator’s manual:
- Contents
- Dear customer!
- Before using a new chain saw
- Important
- Always use common sense
- Personal protective equipment
- Machine¢s safety equipment
- Chain brake and front hand guard
- Will my hand always activate the chain brake during a kickback?
- Will my inetria activated chain brake always activate during kickback in the event of a kickback?
- Will my chain brake always protect me from injury in the event of a kickback?
- Throttle lockout
- Chain catcher
- Right hand guard
- Vibration damping system
- Stop switch
- Muffler
- Cutting equipment
- Fitting the bar and chain
- Fuel
- Fueling
- Fuel safety
- Starting and stopping
- Before use:
- General working instructions
- How to avoid kickback
- General
- Carburetor adjustment
- Checking, maintaining and servicing chain saw safety equipment
- Muffler
- Starter
- Air filter
- Spark plug
- Lubricating the bar tip sprocket
- Needle bearing lubrication
- Adjustment of the oil pump
- Cooling system
- ”Air Injection” centrifugal cleaning
- Winter use
- Heated handles
- Maintenance schedule
- Technical data
- Bar and chain combinations
- Saw chain filing and file gauges
- YOUR WARRANTY RIGHTS AND OBLIGATIONS
- MANUFACTURER¢S WARRANTY COVERAGE
- OWNER¢S WARRANTY RESPONSIBILITIES
- WARRANTY COMMENCEMENT DATE
- LENGTH OF COVERAGE
- WHAT IS COVERED
- WHAT IS NOT COVERED
- HOW TO FILE A CLAIM
- WHERE TO GET WARRANTY SERVICE
- MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
- EMISSION CONTROL WARRANTY PARTS LIST
- MAINTENANCE STATEMENT
- Safety precautions for chain saw users
WORKING TECHNIQUES
English – 29
General advice:
Position yourself so that you will be clear of the tree or
branch when the tension is released.
Make one or more cuts at or near the point of maximum
tension. Make as many cuts of sufficient depth as
necessary to reduce the tension and make the tree or
branch break at the point of maximum tension.
Never cut straight through a tree or branch that is in
tension!
If you must cut across tree/limb, make two to three cuts,
one inch apart, one to two inches deep.
Continue to cut deeper until tree/limb bends and tension
is released.
Cut tree/limb from outside the bend, after tension has
been released.
How to avoid kickback
What is kickback?
The word kickback is used to describe the sudden
reaction that causes the chain saw and bar to jump off an
object when the upper quadrant of the tip of the bar,
known as the kickback zone, touches an object.
Kickback always occurs in the cutting plane of the bar.
Normally the chain saw and bar are thrown backwards
and upwards towards the user. However, the chain saw
may move in a different direction depending on the way it
was being used when the kickback zone of the bar
touched the object.
Kickback only occurs if the kickback zone of the bar
touches an object.
Limbing
Make sure that you can stand and move about safely.
Work on the left side of the trunk. Work as close as
possible to the chain saw for maximum control. If possible,
let the weight of the chain saw rest on the trunk.
Keep the trunk between you and the chain saw as you
move along the trunk.
Cutting the trunk into logs
See instructions under the heading Basic cutting
technique.
!
WARNING! Kickback can happen very
suddenly and violently; kicking the chain
saw, bar and chain back at the user. If
this happens when the chain is moving it
can cause very serious, even fatal
injuries. It is vital you understand what
causes kickback and that you can avoid
it by taking care and using the right
working technique.
!
WARNING! A majority of kickback
accidents occur during limbing. Do not
use the kickback zone of the guide bar. Be
extremely cautious and avoid contacting
the log, other limbs or objects with the
nose of the guide bar. Be extremely
cautious of limbs under tension. They can
spring back toward you and cause loss of
control resulting in injury.