Operator’s manual 570 EPA III 576 XP EPA III Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
KEY TO SYMBOLS Symbols on the machine: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • Approved protective helmet • Approved hearing protection • Protective goggles or a visor Both of the operator′s hands must be used to operate the chain saw. Refuelling. Filling with oil and adjusting oil flow.
CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ..................................... Symbols in the operator’s manual: ....................... CONTENTS Contents ............................................................... INTRODUCTION Dear customer! ..................................................... WHAT IS WHAT? What is what on the chain saw? ........................... GENERAL SAFETY PRECAUTIONS Before using a new chain saw .............................. Important .........................
INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the waterpowered plant.
WHAT IS WHAT? What is what on the chain saw? 1 Decompression valve 16 Bar tip sprocket 2 Switch for heated handle (576XPG) 17 Chain 3 Starter handle 18 Bar 4 Adjuster screws carburetor 19 Bumper spike 5 Stop switch (Ignition on/off switch.
GENERAL SAFETY PRECAUTIONS Before using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping. • Do not use the chain saw until sufficient chain oil has reached the chain. See instructions under the heading Lubricating cutting equipment.
GENERAL SAFETY PRECAUTIONS Always use common sense It is not possible to cover every conceivable situation you can face when using a chain saw. Always exercise care and use your common sense. Avoid all situations which you consider to be beyond your capability. If you still feel uncertain about operating procedures after reading these instructions, you should consult an expert before continuing. Do not hesitate to contact your dealer or us if you have any questions about the use of the chain saw.
GENERAL SAFETY PRECAUTIONS • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism. • The brake is applied when the front hand guard (B) is pushed forwards. • • • To release the chain brake pull the front hand guard backwards, towards the front handle. • Kickback can be very sudden and violent. Most kickbacks are minor and do not always activate the chain brake. If this happens you should hold the chain saw firmly and not let go.
GENERAL SAFETY PRECAUTIONS of the front hand guard, the chain brake can only be activated by the inertia action. Throttle lockout The throttle lockout is designed to prevent accidental operation of the throttle control. When you press the lock (A) (i.e. when you grasp the handle) it releases the throttle control (B). When you release the handle the throttle control and the throttle lockout both move back to their original positions.
GENERAL SAFETY PRECAUTIONS Vibration damping system Muffler Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user. ! The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit.
GENERAL SAFETY PRECAUTIONS • • • Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback. Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.
GENERAL SAFETY PRECAUTIONS • Number of drive links. Sharpening your chain and adjusting depth gauge setting 4 Round file diameter It is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file gauge. This will help you obtain the maximum kickback reduction and cutting performance from your chain. General information on sharpening cutting teeth • Never use a blunt chain.
GENERAL SAFETY PRECAUTIONS • General advice on adjusting depth gauge setting • resistance as you draw the file along the depth gauge tool. File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced. Tensioning the chain When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease.
GENERAL SAFETY PRECAUTIONS Lubricating cutting equipment Checking chain lubrication • ! WARNING! Poor lubrication of cutting equipment may cause the chain to snap, which could lead to serious, even fatal injuries. Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket. Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away.
GENERAL SAFETY PRECAUTIONS Chain drive sprocket Bar The clutch drum is fitted with one of the following drive sprockets: Check regularly: • Whether there are burrs on the edges of the bar. Remove these with a file if necessary. A Spur sprocket (the chain sprocket is welded on the drum) B Rim sprocket (replaceable) Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain.
ASSEMBLY Fitting the bar and chain ! correctly located in the groove in the bar. Tighten the bar nuts finger tight. WARNING! Always wear gloves, when working with the chain. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A). Fit the bar over the bar bolts. Place the bar in its rearmost position.
FUEL HANDLING Fuel Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. Mixing ratio 1:50 (2%) for all engines. Gasoline, litre WARNING! Always ensure there is adequate ventilation when handling fuel.
FUEL HANDLING Fueling ! • Move the machine at least 10 ft (3 m) from the refuelling point before starting it. • Never start the machine: 1 If you have spilled fuel or chain oil on the machine. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water. 3 If the machine is leaking fuel.
STARTING AND STOPPING Starting and stopping ! the machine has started the valve will automatically return to its closed position. WARNING! Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries. Place the machine on firm ground.
STARTING AND STOPPING throttle latch in order to avoid unnecessery wear on the clutch assembly. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is ready for use. ! drop start. This method is very dangerous because you may lose control of the saw. • Never start the machine indoors.
WORKING TECHNIQUES Before use: Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To make sure that none of the above might come within reach of your saw or be injured by falling trees. , 1 Check that the chain brake works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle lockout works correctly and is not damaged.
WORKING TECHNIQUES 6 Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance. 7 When you put the chain saw on the ground, lock the saw chain using the chain brake and ensure you have a constant view of the machine. Switch the engine off before leaving your chain saw for any length of time.
WORKING TECHNIQUES user. If the saw chain is jamming, the saw may be pushed back at you. Terms Cutting = General term for cutting through wood. Limbing = Cutting branches off a felled tree. Splitting = When the object you are cutting breaks off before the cut is complete.
WORKING TECHNIQUES Limbing When limbing thick branches you should use the same approach as for cutting. If it is possible (can you turn the log?) stop cutting about 2/3 of the way through the log. Cut difficult branches piece by piece. 1 2 3 Cutting ! Turn the log and finish the cut from the opposite side. The log is supported at one end. There is a high risk that it will split. WARNING! Never attempt to cut logs while they are in a pile or when a couple of logs are lying together.
WORKING TECHNIQUES Tree felling technique IMPORTANT! It takes a lot of experience to fell a tree. Inexperienced users of chain saws should not fell trees. Do not attempt any task beyond your experience level! The main point to avoid is letting the tree fall onto another tree. It is very dangerous to remove a trapped tree and there is high accident risk. See instructions under the heading Freeing a tree that has fallen badly.
WORKING TECHNIQUES Felling ! Make the felling cut about 1.5-2 inches (3-5 cm) above the bottom directional cut. WARNING! Unless you have special training we advise you not to fell trees with a diameter larger than the bar length of your saw! Felling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then you finish with the felling cut. By placing these cuts correctly you can control the felling direction very accurately.
WORKING TECHNIQUES find out which lengths of bar are recommended for your saw. There are methods for felling trees with a diameter larger than the bar length. However these methods involve a much greater risk that the kickback zone of the bar will come into contact with the tree. The safest method is to use a winch. • Tractor-mounted • Portable Cutting trees and branches that are in tension Preparations: Work out which side is in tension and where the point of maximum tension is (i.e.
WORKING TECHNIQUES How to avoid kickback ! WARNING! Kickback can happen very suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique.
MAINTENANCE General Basic settings and running in The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorized service workshop. The basic carburetor settings are adjusted during testing at the factory. Avoid running at a too high speed for extended periods during the first 10 hours. Carburetor adjustment CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops. Rec.
MAINTENANCE When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance. The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position. The limiter cap limits the potential to adjust the high speed jet to at most half a turn. CAUTION! There is an integrated speed governor in the ignition system that limits the maximum speed to 13300 rpm.
MAINTENANCE Checking the brake trigger • Check that the throttle control and throttle lockout move freely and that the return springs work properly. • Start the chain saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationary. If the chain rotates when the throttle control is in the idle position you should check the carburetor idle adjustment. Place the chain saw on firm ground and start it.
MAINTENANCE Make sure the vibration damping units are securely attached to the engine unit and handle unit. Stop switch The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material. Starter ! Start the engine and make sure the engine stops when you move the stop switch to the stop setting.
MAINTENANCE Tensioning the recoil spring • Air filter Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise. Note! Check that the pulley can be turned an additional 1/2 turn when the starter cord is pulled all the way out. 1 2 The air filter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption.
MAINTENANCE Spark plug Needle bearing lubrication The spark plug condition is influenced by: The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week). • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dirty air filter. These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.
MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Air guide plate. 3 Fins on the flywheel. 4 Cooling fins on the cylinder. 5 Cylinder cover (directs cold air over the cylinder). Clean the cooling system with a brush once a week, more often in demanding conditions.
MAINTENANCE Temperature -5°°C (23°°F) or colder: For running the machine in cold weather or powder snow, a special cover is available, which is mounted on the starter housing. This reduces the intake of cold air and prevents large amounts of snow from being sucked in. A B C CAUTION! If the special winterising kit has been fitted or any measures have been taken to increase the temperature these changes must be reversed before the machine is used in normal temperature conditions.
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Weekly maintenance Monthly maintenance Clean the outside of the machine. On chain saws without a catalytic converter, check the cooling system weekly. Check the brake band on the chain brake for wear. Replace when less than 0.024 inch (0.6 mm) remains at the most worn point.
TECHNICAL DATA Technical data 570 576XP Cylinder displacement, cu.
TECHNICAL DATA Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for Husqvarna chain saw models 576XP, 576XPG and 570. These chain saw models equipped with either of the listed bar and sawchain combinations, fulfills the requirements according to ANSI B 175.1-2000 (Gasoline Powered Chain Saws - Safety Requirements).
FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2009 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards.
AMERICAN STANDARD SAFETY PRECAUTIONS Safety precautions for chain saw users (ANSI B175.1-2000 Annex C) Kickback safety precautions ! WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction, kicking the guide bar up and back towards the operator.
´®z+TCG¶5S¨ ´®z+TCG¶5S¨
1152353-95 ´®z+TCG¶5S¨ ´®z+TCG¶5S¨ 2009-06-11