Operation Manual

emoviflg
the
bobbin case
open
the
door
in front
of
the
shuttle
by means
of
the
small
recesS
on
the
left side.
GriP
the
bobbin
case
with
the
thumb
and
index
finger
so
that
the
latch
is
depressed
and
pull
the bobbin case
out.
The
bobbin
will
remain
in
the
case
as
long
as
the
latch
is
dePress&J
When
you
release
the
latch,
the
bobbin
will
be
released.
Bobbin
winding
Turn
the
empty
bobbin
until
the
small
round
mark
on
one
side
15
outward.
Slide
the
bobbin
onto
the
bobbin
winding
spindle
located
n
the
right
side
of
the
machine. Raise
the
presser foot
and
pull
the
thread
from
the
thread
guide
on
the
needle
clamp
through
the
thread
guide
on
the
right
of
the
machine
to
the
bobbin.
Wind
the
thread
around
the
bobbin
a
couple
of
times,
eginnmg
from
underneath,
you
are
using
a
metal
nreSser
foot,
allow
the
thread
to
go
through
the
eye of
the
eedle
and
under
the
presser
foot.
Never
run
the
thread
direct
from
the
eye of
the
needle
to the
bobbin
because
iou
will
run
the
risk
of bending
the
needle.
Hold
the
thread
nd
and
lightly
depress
the
foot
control.
As
soon
as wind
ing
starts
you
can
release
the
thread
end.
threadIng
the
lower
thread
When
the
bobbin
winding
is
finished,
place
the
bobbin
in
its
case
with
the
marking
upward.
The
thread
should
run
as
shown
in
the
figure.
Slide
the
thread
into
the
slot
on
the
edge
of the
bobbin
case.
Pull
the
thread
in
under
the
tension
spring.
Check
that
the
bobbin
rotates
in the
direction
of
the
arrow
(clock
wise)
when
the
thread
is
pulled.
The
thread
must
be
pulled
in
the
direction
of
the spring,
otherwise
the
spring
will
be
overloaded.
Insertion
of
the
bobbin
case
Slide
the
thread
behind
the
projection
of the
bobbin
case
and
to
the
right.
Put
the
bobbin
case
into
place.
Press
the
bobbin
case
until
it
clicks
to
ensure
that
it
fits properly. The
thread
cutter
is
located
to
the
left of
the
bobbin
case.
Hold
the
thread
end
and
draw
the
thread
from
underneath
and
up
toward
the
thread
cutter.
By doing
so
the
thread
will
be
cut
off
and
kept
in
place.
Shut
the
door.
Threading
the
upper
thread
Raise
the
presser
foot.
Check
that
the
needle
is
at
its
highest
position.
Place
the
spool
of thread
on
the
left spool
pin
and
thread
the
machine
for
sewing.
Slide
the
thread
into
thread
guide
2
on
the
upper
arm
and
draw
it
upward.
Then
draw
the
thread
to
the
front
between
the tension discs
3
and
down
around
thread
guide
4.
Continue
threading by
drawing
the
thread
from
the right
into
the
slot on
thread
take-up
lever
5
and
draw
it down
to
the
needle,
ensuring that
it goes
through
thread
guide
6.
Thread
the
needle
from
the
front.
Due
to the
white
color
of
the
presser
foot
ankle
the
needle-eye
is
clearly
seen
and
the
threading of
the
needle
7,
is easier.
Pull
the
thread
under
the
presser
foot
about
15 cm
(6”)
toward
the
rear.