Operation Manual

6 Embroidery Set Up
A
B
6:4
TO HOOP THE FABRIC
)RUWKHEHVWHPEURLGHU\UHVXOWVSODFHDOD\HURI stabilizer
beneath the fabric. When hooping stabilizer and fabric
make sure that they are smooth and securely hooped.
 2SHQWKH4XLFN5HOHDVH$RQWKHRXWHUKRRSDQG
ORRVHQWKHVFUHZ%5HPRYHWKHLQQHUKRRS3ODFH
WKHRXWHUKRRSRQDÀUPÁDWVXUIDFHZLWKWKHVFUHZRQ
WKHORZHUULJKW%7KHUHLVDVPDOODUURZLQWKHFHQWHU
of the lower edge of the hoop which will line up with
a small arrow on the inner hoop.
2. Place the stabilizer and fabric, with the right sides
facing up, on top of the outer hoop. Place the inner
hoop on top of the fabric with the small arrow at the
bottom edge. If you can see the hoop size in the lower
SDUWRI WKHLQQHUKRRS\RXKDYHDWWDFKHGLWFRUUHFWO\
 3XVKWKHLQQHUKRRSÀUPO\LQWRWKHRXWHUKRRS
 &ORVHWKH4XLFN5HOHDVH$$GMXVWWKHSUHVVXUHRI 
WKHRXWHUKRRSE\WXUQLQJWKHUHWDLQLQJVFUHZ%7KH
fabric should be taut in the hoop for the best results.
Note: When embroidering additional designs on the same fabric, open
the quick release, move the hoop to the new position on the fabric and
close the quick release. When changing type of fabric, you might need
to adjust the pressure using the retaining screw. Do not force the quick
release.
SLIDE ON THE HOOP
Make sure that the accessory tray on the embroidery unit is
FORVHG6OLGHWKHKRRSFRQQHFWRULQWRWKHKRRSDWWDFKPHQW
from front to back until it clicks into place.
7RUHPRYHWKHKRRSIURPWKHHPEURLGHU\DUPSUHVVWKH
grey button on the hoop attachment and slide the hoop
towards you.
AUTOMATIC JUMP STITCH TRIM
7KLVPDFKLQHIHDWXUHV$XWRPDWLF-XPS6WLWFK7ULP7KLV
IXQFWLRQVDYHV\RXWLPHWULPPLQJDIWHUWKHHPEURLGHU\LV
FRPSOHWHG$V\RXHPEURLGHUWKHPDFKLQHZLOOWULPWKHWRS
jump stitch thread and pull the thread end to the underside
of the fabric.
The default setting is on. To turn it off, go to the 6(7
0HQX6HZLQJ6HWWLQJVDQGGHVHOHFW$XWRPDWLF-XPS6WLWFK
Trim.
NOTE: The machine will also cut the thread after you have changed
to a new thread color. When you start embroidering again, hold the
thread end so you can easily remove it after it is cut.
1RWDOOGHVLJQVDUHSURJUDPPHGIRU$XWRPDWLF-XPS6WLWFK
Trim. Jump stitch trim commands can be added to any
GHVLJQXVLQJWKHFRPSOLPHQWDU\VRIWZDUH3&5HDGPRUH
DERXW$XWRPDWLF-XPS6WLWFK7ULPLQFKDSWHU
C