User’s Guide Limited Edition K E E P I N G T H E WO R L D S E W I N G
This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this household sewing machine. DANGER - To reduce the risk of electric shock: • • A sewing machine should never be left unattended when plugged in.
Presser Foot Kit A limited edition accessory foot package is packed in the box with your HUSQVARNA VIKING® Eden Rose™ sewing machine. The package contains the following optional presser feet: Gathering Foot (4127971-45) Gather fabric or gather and attach a ruffle in one step. Suitable for light to medium weight fabrics. Straight stitch, (left needle position), length 4. The longer the length, the more fabric will gather. Snap on Gathering Foot.
CLEAR PIPING FOOT (4130971-45) Insert packaged piping into seams and edges for a tailored finish. Cover cord with fabric for specialty piping. The clear view allows you to see the piping placement and see exactly where you are stitching. The clear view enables you to see the first row of stitching and adjust your needle position to stitch next to the original row. Straight Stitch, length 2.5. To Make Piping From Your Fabric: 1. Snap on the Clear Piping Foot. 2.
Table of Contents Overview.....................................................................4 Extension Table..........................................................5 Standard Accessories and Storage................6 Getting Ready to Sew 7 Connecting the Power Supply.........................7 Adjusting the Sewing Speed..............................8 Speed Control Slide..............................8 Foot Control..........................................8 Needle up/down..............................
Overview 1. Bobbin stop 2. Bobbin spindle 3. Hole for extra spool pin 4. Spool holder 5. Spool pin 6. Thread guide for bobbin winding 7. Thread take-up lever 8. Presser foot pressure dial 9. Face plate 10. Thread cutter 11. Needle threader 12. Needle plate 13. Extension table (Accessory storage) 14. Bobbin cover plate 15. Bobbin cover plate release button 16. Thread tension dial 17. Needle up/down button 18. Speed control slider 19. Reverse stitch lever 20. Sewing Guide 21. Stitch length dial 22.
Extension Table To remove Hook your fingers on the bottom left of the extension table and pull it to the left. Free-arm sewing For stitching sleeves, waistbands, pant legs or any other tubular garments. For darning socks or mending knees or elbows. To attach Slide the extension table on and insert the pins into the holes and push the extension table to snap it in place. 1. Pin 2.
Standard Accessories and Storage 1. Utility Foot A 2. Utility Foot B 3. Buttonhole Foot C 4. Adjustable Blind Hem Foot 5. Zipper Foot E 6. Non-stick Glide Foot H 7. Edging Foot J 8. Automatic Buttonhole Foot R 9. Transparent Foot B 10. Quilter’s 1/4” Piecing Foot P 11. Self-adhesive Glide Plates 12. Edge/quilting Guide 13. Needles 14. Bobbins 15. Screwdriver 16. Lint brush 17. Seam ripper (Buttonhole opener) 18. Spool holder (Large) 19. Spool holder (Small) 20. Vertical spool pin 21. Felt cushion 22.
Getting Ready to Sew Connecting the Power Supply Turn the power switch off. 1 5 Before plugging in the foot control, check to ensure that it is of type “21361” (see underside of foot control). Insert the foot control plug into the machine socket. 6 3 4 2 Insert the power supply plug into the machine and the wall outlet. Turn the power switch on. 1. Power switch 2. Foot control plug 3. Machine plug 4. Machine socket 5. Power supply plug 6.
Adjusting the Sewing Speed You can control the sewing speed in two ways; with the speed control slide or with the foot control. Speed Control Slide With the speed control slide, you can change the sewing speed to suit your needs. The slide limits how fast you can sew. To increase the sewing speed, slide the bar to the right. To reduce the sewing speed, slide the bar to the left. Foot Control You can control the sewing speed by using the foot control.
Sewing Guide Reference Chart Consult the Sewing Guide Reference Chart for the fast easy way to select the best stitch, stitch length, stitch width, thread tension, presser foot and presser foot pressure for your sewing technique and fabric. Look in the column for your fabric type: woven fabrics: for stable fabrics that have no stretch. Usually woven. stretch fabrics: for fabrics that have stretch. Usually knit. leather/vinyl: for suede, real leather and for artificial leather and suede.
Reverse Lever When you press the reverse lever downwards, the machine will sew in reverse. The machine will only sew in reverse as long as the reverse lever is pressed down. 1. Reverse lever 1 Presser Foot Pressure Dial Turn the pressure dial to adjust the pressure of the presser foot on the fabric when sewing on different thicknesses of fabric. The pressure dial should be set at 3 for regular sewing. Reduce the pressure to 2 for appliqué, cutwork and basting.
Raising and Lowering the Presser Foot The presser foot is raised and lowered with the presser foot lever. The presser foot must be down when sewing. By raising the presser foot lever as far as it goes the lift height of the presser foot can be increased by 1/4” (0.6 cm). This is useful for easy removal of the presser foot or when placing heavy fabrics under the foot. 1. Lowered position 2. Normal lift height 3. Extra lift height Changing the Presser Foot 3 3 2 2 1 1 Turn off the power switch 1.
Changing the Needle Turn off the power switch. Your machine uses standard sewing machine needles. 1. Lower the presser foot. Loosen the screw in the needle clamp by turning it counterclockwise. Remove the needle. 2. Push up the new needle as far as it will go with the flat side away from you. Tighten the screw firmly by turning it clockwise. a. Stop b. Flat side c. Needle clamp screw To Check for a Good Needle: Put the flat side of the needle onto something flat (needle plate, glass etc.).
Placing the thread spool on the spool pin Place the thread spool on the spool pin with the thread coming off as illustrated. With large thread spools, the large holder is placed in front of the thread. If you use narrow thread spools, the small holder is placed in front of the thread. 1 1. Large spool holder 2. Small spool holder 2 Removing the bobbin 1 Turn off the power switch. 1. Push the bobbin cover release button to the right and remove the cover. a a. Release button b. Bobbin cover plate 2.
3 1 b a c 2 Bobbin Winding 1. Pull the handwheel out to put the machine in bobbin wind position (the needle will not go up and down). 2. Guide the thread around the bobbin thread tension guide into the tension disk. 3. Thread through the hole in the bobbin from the inside to the outside. Put the bobbin on the bobbin winder spindle with the free end of the thread coming out at the top. 4. Slide the bobbin winder spindle to the right. Note: Do not move the bobbin winder spindle while the machine is running.
Placing the bobbin Turn off the power switch 1. Place the bobbin in the bobbin case with the thread pulling off as illustrated. 2. Guide the thread into the front notch (a) on the front side of the bobbin case. Draw the thread to the left, sliding it between the tension spring blades. 1 2 a 3. Continue to draw the thread lightly until the thread slips into the side notch (b). 3 b 4. Pull out about 10 cm (4”) of thread. Attach the bobbin cover.
Threading the Machine Turn off the power switch Make sure the presser foot is raised and the needle is in the up position. 1 3 2 4 1. 2. Bring the thread from the spool and pass it through the thread guide. Then draw it down along the right slot. Guide the thread around the bottom of the thread guide plate. 3. Firmly draw the thread from right to left over the take-up lever and down into the take-up lever eye. 4. Slide the thread from the left behind the needle bar thread guide. 5.
Needle threader Turn off the power switch 1 1. Raise the needle to its highest position. Lower the needle threader as far as it will go. The hook comes through the needle eye from behind. 2. Bring the thread from the left around the guide and under the hook. a. Guide b. Hook 2 a 3. Release the knob slowly while holding the thread end with your hand. A loop of the thread is pulled through the needle eye. 4. Pull the loop of thread behind the needle eye.
Bringing up the Bobbin Thread Turn off the power switch. 1. Raise the presser foot and hold the needle thread lightly with your left hand. 2. Turn the handwheel slowly toward you one complete turn. Bring the bobbin thread up by pulling the needle thread as illustrated. 1 2 b a. Needle thread b. Bobbin thread 3. Pull 10 cm (4”) of both threads back and under the presser foot.
Stitches Stretch stitches Stitch selection Raise the needle to its highest position. Turn the stitch selection dial to set the desired stitch pattern number at the setting mark. 1. Stitch selection dial 2. Setting mark Note Always raise the needle above the fabric and presser foot before you turn the stitch selction dial. Stitch Length Turn the stitch length dial to set the desired stitch length number at the setting mark. The higher the number, the longer the stitch.
Adjusting stretch stitch balance If the stretch stitches are unbalanced when you sew on a particular fabric, balance them by turning the stitch length dial, within the stretch range. To Adjust the Distorted Stitches: If the stitches are spread out (a), correct them by turning the dial in the “–” direction. If the stitches are close together (b), correct them by turning the dial in the “+” direction. Stitch Width Turn the stitch width dial to set the desired stitch width number at the setting mark.
Balancing Needle Thread Tension The thread tension may be adjusted depending on the sewing materials, layers of fabric and sewing method. 1 4 3 Balanced Tension: The ideal straight stitch has threads locked between two layers of fabric, as illustrated. For an ideal zigzag stitch, the bobbin thread does not show on the right side (top side) of the fabric, and the needle thread shows slightly on the wrong side (bottom side) of the fabric. 1. Needle thread 2. Bobbin thread 3. Right side 4.
Basic Sewing Straight Stitch Sewing Machine Setting Consult the Sewing Guide Reference Chart for the settings recommended. Starting to Sew Raise the presser foot and position the fabric next to a seam guide line on the needle plate. Lower the needle to the point where you want to start. Lower the presser foot and pull the threads toward the back. Press the foot control. Gently guide the fabric along the seam guide line letting the machine feed the fabric.
Finishing sewing 1. Press the reverse lever and sew several stitches in reverse at the end of the seam, to lock the stitch. 1 2. Raise the presser foot and remove the fabric, drawing the threads to the back. 2 3. Draw the threads up and into the thread cutter. The threads are cut the proper length for starting the next seam.
Seam Guides on the Needle Plate The seam guides on the needle plate help you measure seam allowance. The numbers indicate the distance between the center needle position and the seam guide. 1. Seam guides 1 Number Spacing (cm) 15 20 4/8 5/8 6/8 1.5 2.0 1.3 1.6 1.9 Pivoting Seam along the 5/8” guide. Stop stitching and lower the needle when the fabric edge facing you lines up with the cornering guides as shown. Raise the presser foot and pivot the fabric to line up to the edge with the 1.
Utility Sewing Consult the Sewing Guide Reference Chart for the fast easy way to select the best stitch, stitch length, stitch width, thread tension, presser foot and presser foot pressure for your sewing technique and fabric. Basic Zigzag Simple zigzag stitching is widely used for overcasting, sewing on buttons etc. Three-step Zigzag When using the Edging Foot J for threestep zigzag, make sure the needle does not hit the pin in the needle hole. Three-step zigzag is suitable for overcasting most fabrics.
Reinforced Straight Stitch Machine setting 1. Stitch pattern: 1 2. Stitch width: 0 or 5 3. Stitch length: stretch 4. Thread tension: 2 – 5 5. Presser foot: Utility foot A This stitch is stronger than regular straight stitch, due to the fact that it is a triple and elastic stitch. The reinforced straight stitch can be used for heavy stretch fabrics, for crotch seams which are subject to considerable strain and for topstitching in heavy fabrics. Button Sewing Machine setting: 1. Stitch: 2 2.
Automatic Buttonhole Machine setting 1. Stitch pattern: 2. Stitch width: 4 – 5 3. Stitch length: 4. Thread tension: 3 – 5 5. Presser foot: Automatic buttonhole foot R Note: The size of buttonhole is automatically set by placing the button in the automatic buttonhole foot R. The button holder of the foot takes a button size up to 2.5 cm (1”) in diameter. Make a test buttonhole on a fabric sample duplicating the interfacing and seams of the actual garment. Use stabilizer under all fabric.
3 Pull the buttonhole lever down as far as it will go. a. Buttonhole lever 3 a 4 Raise the foot and put the needle thread through the hole and under the foot. Draw both threads to the left. Insert the fabric under the foot and lower the needle at the starting point. Lower the foot. b. c. d. e. Needle thread Bobbin thread Hole Starting point Note: Make sure there is no gap between the slider and front stop. If there is a gap, the length of the right and left rows of the buttonhole will differ. f. g.
5. Sew slowly. The machine will stitch the complete buttonhole. Stop the machine at the starting point when the buttonhole is completed. The machine sews the front bartack and left column first, then the back bartack and right column. 6. Raise the foot and remove the fabric.Cut both needle and bobbin threads leaving about 10 cm (4”) of thread ends loose. Draw the needle thread to wrong side of the fabric by pulling the bobbin thread. Then, knot the threads.
7. When finished, push the buttonhole lever up as far as it will go. 7 Adjusting the Buttonhole Stitch Density Turn the stitch length dial within the range of to adjust the buttonhole stitch density. Note: If the button is extremely thick, make a test buttonhole. If it is difficult to fit the button through the test buttonhole, lengthen the size by pulling back the button holder which will increase the buttonhole length. 1.
Corded Buttonhole Machine setting: 1. Stitch pattern: 2. Stitch width: 4 – 5 3. Stitch length: 4. Thread tension: 3 – 5 5. Presser foot: Automatic buttonhole foot R 1. With the buttonhole foot raised, hook the filler cord on the spur at the back of the buttonhole foot. Bring the cord under the foot and hook the filler cord into the notches on the front of the foot to hold them tight. a. Spur 2. Draw both needle and bobbin thread to the left.
Manual Buttonhole Consult the Sewing Guide Reference Chart for recommended settings. If the diameter of the button is more than 2.5 cm (1”), make the buttonhole manually as follows: 1. Snap on buttonhole foot C. 2. Pull the buttonhole lever down as far as it will go. Draw both needle and bobbin thread to the left. Lower the needle into the fabric where the buttonhole is to start, and lower the foot. a. Needle thread b. Bobbin thread c.
4. Sew the front bartack and left column to the desired length then stop sewing. 5. Pull the buttonhole lever toward you. 6. Sew the back bartack and right column and then stop sewing at the starting point. 7. When finished, push the buttonhole lever up as far as it will go.
Sewing Zipper Machine setting 1. Stitch pattern: 1 2. Stitch width: 5 3. Stitch length: 1.5 – 4 4. Thread tension: 3 – 6 5. Presser foot: Zipper foot E 1 2 4 3 5 To Snap On the Zipper Foot Snap on the zipper foot. 1. Groove 2. Pin To sew the left side of the zipper, snap on zipper foot on the right bar on the side. To sew the right side of zipper, snap on the zipper foot on the left bar on the side. Fabric Preparation 2 1 1 1. Add 1 cm (3/8”) to the zipper size for the overall opening size. a. b.
2. Place right sides of the fabric together. Sew a seam from the bottom 2 cm (5/8”) from the right edge to the end of the zipper opening. Sew a few stitches in reverse to lock. Increase the stitch length to “4”, set needle thread tension to “1”, and baste the length of the zipper opening. j. 2 cm (5/8”) k. Basting l. Reverse stitch m. End of the opening n. Straight stitch 2 n l m k j a 1 b To Sew 1. Snap on the zipper foot with the bar on the right side.
3. Sew through all layers next to the fold. Stop just before the zipper foot reaches the slider on the zipper tape. Lower the needle slightly into the fabric. Raise the zipper foot and open the zipper. Lower the foot and stitch the remainder of the seam. 3 i i. Slider j. 5 cm (2”) 4. Close the zipper and spread the fabric flat with the right side facing up. Baste the opened fabric and zipper tape together. j 4 k. Basting l.
5. Remove the zipper foot and snap on with pin on left side. Guide the edge of the foot along the zipper teeth and stitch through the fabric and zipper tape, about 1 cm (3/8”) distance from the basting line. Stop about 5 cm (2’’) from the top of the zipper. 5 n m. Remove the basting stitches n. 1 cm (3/8”) 6. Unzip a few centimeters/inches to clear a path for the stitch. At end of seam, sew a few stitches in reverse to lock.
Blind Hem Consult the Sewing Guide Reference Chart for recommended settings. 1. Fold the hem under the fabric as illustrated for fine or medium fabrics. Fold a hem with the wrong side up forming a 0.5 cm (1/8”) allowance. a. b. c. d. 1 b a d a c d Wrong side of the fabric 0.5 cm (1/8”) Heavy weight fabric Light/medium weight fabric 2. Snap on the adjustable blind hem foot. Place hem under the presser foot.
PRESSER FEET Non-stick Glide Foot H Consult the Sewing Guide Reference Chart for recommended settings. When sewing foam, plastic, plastic coated fabrics, leather and imitation leathers, the Non-stick Glide Foot H feeds over the fabric without sticking. Use it for general sewing and buttonholes on plastic and leather type fabrics. Snap on the Non-stick Glide Foot H. Select desired stitch and sew. Quilting Guide The quilting guide will help keep stitching lines straight.
Quilter’s 1/4” Piecing Foot Sew a scant 1/4” seam allowance. Red lines mark 1/4” and 1/8” pivot points in front of and behind the needle. Straight stitch, length 2.0-2.5. Place to pieces of fabric right sides together. Sew with edge of fabric at edge of foot. To pivot 1/4” from end of fabric, stop sewing with needle stop down, when fabric edge reaches first red mark on foot.
Care and Maintenance Turn off the power switch. Do not dismantle the machine other than as explained in this section. Clean the outside of the machine with a soft cloth and mild soap. Cleaning the Hook Assembly area and Feed Teeth 1. Remove the presser foot and needle. Remove screw on the left side of the needle plate with the screwdriver supplied with the machine. Remove the needle plate and take out the bobbin. a. Screw 2. Lift up the bobbin case and remove it. 1 a 2 3 3. Brush out dust and lint. 4.
Replacing the Bobbin Case Turn off the power switch. 1. Insert the bobbin case into the hook assembly area. 2. Make sure the knob of the bobbin case fits next to the stopper in the assembly area. 1 2 a. Knob b. Stopper b 3. Insert the bobbin. Replace the needle plate, inserting the two needle plate guide pins into the holes in the needle plate. Replace the screw. c. Guide holes d. Screw a 3 c d c Replacing the Light Bulb Turn off the power switch.
Troubleshooting CONDITION /CAUSE The Needle Thread Breaks • • • • • The needle thread is not threaded properly. The needle thread tension is too tight. The needle is bent. The needle is incorrectly inserted. The needle thread and the bobbin thread are not placed under the presser foot at start of sewing. • The threads were not drawn to the rear after sewing. The Bobbin Thread Breaks • The bobbin thread is not threaded properly in the bobbin case. • Lint has collected in the bobbin case.
CONDITION /CAUSE The Cloth Is Not Fed Smoothly 44 REFERENCE • The feed teeth are packed with lint. • The stitchlength is too short. • The feed teeth are not raised after ”drop feed” sewing. Page 41 Make stitch longer Page 10 Loops On The Seams • The needle thread tension is too loose. Page 21 The Machine Does Not Work • The machine is not plugged in. • Thread has been caught in the hook. • The bobbin winder spindle is still in the winding position.
We reserve the right to change the machine equipment and the assort-ment of accessories without prior notice, or make modifications to the performance or design. Such modifications, however, will always be to the benefit of the user and the product. Intellectual Property VIKING, KEEPING THE WORLD SEWING & Design, and EDEN ROSE are trademarks of KSIN Luxembourg II, S.ar.l. HUSQVARNA and the “crowned H-mark” are trademarks of Husqvarna AB. All trademarks are used under license by VSM Group AB.
Scan ries! 413 36 59-26A • English • Inhouse • © 2012 KSIN Luxembourg II, S.ar.l. • All rights reserved • Printed in Germany on environmental-friendly paper w w w. husqv ar nav i ki ng.