Operator Manual EZ4824K / 966038201 EZC4824BF / 966047501 EZ5224 / 966038301 EZ5224BF / 966495901 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
In order to implement improvements, specifications and designs can be altered without prior notification. Note that no legal demands can be placed based on the information contained in these instructions. Use only original parts for repairs. The use of other parts voids the warranty. Do not modify or install non-standard equipment to the unit without consent from the manufacturer. Modifications to the unit may cause unsafe operations or damage the unit.
Contents INTRODUCTION.......................................................5 Driving and Transport on Public Roads..............5 Towing.................................................................5 Operating............................................................5 Good Service......................................................6 Manufacturing Number.......................................6 Symbols and Decals..........................................7 Safety........................................
WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower.
INTRODUCTION Congratulations Towing Thank you for purchasing a Husqvarna ride-on mower. This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance. This manual is a valuable document. Read the contents carefully before using or servicing the machine.
INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer.
symbols and decals These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. IMPORTANT INFORMATION WARNING! Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.
symbols and decals Read Operator’s Manual Shut off engine and remove key before performing any maintenance or repair work Whole body Severing of fingers exposure to and toes thrown objects Moving sharp blades under cover 8 Keep a safe distance from the machine Use on slopes no greater than 10° No passengers Do not open or remove safety shields while engine is running Careful backing up, watch for other people Careful going forward, watch for other people
SAFETY Safety Instructions These instructions are for your safety. Read them carefully. WARNING! WARNING! THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. This symbol means that important safety instructions need to be emphasized. It concerns your safety. General Operation • Read, understand, and follow all instructions on the machine and in the manual before starting.
SAFETY • • • • • • • • • • • 10 Operate machine only in daylight or good artificial light. Do not operate the machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways. Use extra care when loading or unloading the machine into a trailer or truck. Always wear eye protection when operating machine. Data indicates that operators age 60 years and above are involved in a large percentage of riding mower-related injuries.
SAFETY Personal Safety Equipment WARNING! When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment. • • • • • • • Make sure that you have first aid equipment close at hand when using the machine. Never use the machine when barefoot.
SAFETY Children Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. • Be alert and turn machine off if a child enters the area. • Before and while backing, look behind and down for small children.
SAFETY WARNING! The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed. Safe Handling of Gasoline To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Use only approved gasoline containers. • Never remove gas cap or add fuel with the engine running.
SAFETY General Maintenance • • • • • • • • • • • • • • • • • 14 Never operate machine in a closed area. Keep all nuts and bolts tight to be sure the equipment is in safe working condition. Never tamper with safety devices. Check their proper operation regularly. Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage and remove any fuel-soaked debris. Allow machine to cool before storing. If you strike a foreign object, stop and inspect the machine.
SAFETY Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery. WARNING! Avoid electrical sparking and its consequences by the following routines: • • • • • • • • Use protective goggles. Ensure that the fuel filler cap is mounted tightly and no flammable substances are stored in an open vessel.
SAFETY • The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine. The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them. Check the parking brake’s functionality regularly. Adjust and service as necessary. The mulch blades should only be used in familiar areas when higher quality mowing is desired.
CONTROLS This operator’s manual describes the Husqvarna Zero Turn Rider. The rider is fitted with either a Kohler fourstroke overhead valve engine. Transmission from the engine is made via a belt- driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the direction and speed. Control Locations 13 2 7 1 9 4 8 1. 2. 3. 4. 5. 6. 7. 5 3 Steering control levers Parking brake Throttle control Blade switch Ignition switch Choke control Fuses 6 12 8. 9.
CONTROLS Steering Control Levers The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward. When both controls are in the neutral position (N), the machine stands still.
CONTROLS Parking Brake IMPORTANT INFORMATION The machine must stand absolutely still when applying the parking brake. Always set the parking brake before dismounting. Release the parking brake before moving the mower. The parking brake is found on the left of the machine. Push button and pull the lever backward to activate the brake and push button and push forward to release it.
CONTROLS Ignition Switch The ignition key is placed on the control panel and is used to start and stop the engine. Ignition switch 8052-001 Choke Control The choke control is used for cold starts in order to provide the engine with a richer fuel mixture. For cold starts the control should be pulled out. 8052-001 Choke control Fuses Fuses are located under the seat of the machine. They are accessed by tilting the seat forward. They are flat pin fuses of the same type used in automobiles.
CONTROLS Fuel Tank Read the safety instructions before refueling. The machine has one fuel tank, just behind the seat. The tank capacity is 4 gallons (15.1 liters). Regularly check the gas cap gasket for damage and keep the cap properly tightened. The engine will run on a minimum of 87-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See also Technical Data concerning ethanol fuel. Methanol fuel is not allowed. Do not use E85 alcohol based fuel.
CONTROLS Fuel Shut Off Valve The fuel shut off valve is located at the left rear of the seat. The valve is off when the handle tab is turned perpendicular to the fuel line. Fuel shut off valve in the CLOSED position 8011-419 Cutting Height Adjuster The deck cutting height is obtained by pressing the button and moving the lever forward to the correct cutting height on the cutting plate. The cutting height range is from 1½" (38mm) to 4" (102mm) in ½ (13mm) increments.
CONTROLS Seat Adjustment Lever The seat can be adjusted lengthways. When making adjustments, the lever under the right front side of the seat is pulled to the side, after which the seat can be moved backward or forward. Lengthways adjustment 8058-034 Hour Meter The hour meter displays the total operating time. It will flash CHG OIL (Change Oil) at 50 hour intervals. The flash duration is one hour before and one hour after the interval. The CHG OIL icon will come on and shut off automatically.
operation Read “Safety Instructions” section and following pages, if you are unfamiliar with the machine. Training Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities. We suggest that this section be reviewed in its entirety prior to attempting to move the mower under its own power.
operation Before Starting • Read the sections Safety Instructions and Controls before starting the machine. • Perform the daily maintenance before starting (see Maintenance Schedule in the Maintenance section). • Check that there is sufficient fuel in the fuel tank. • Adjust the seat to the desired position. The following conditions must be fulfilled before the engine can be started: • The blade switch for engaging the mower blades must be depressed. • The parking brake must be on.
operation Move the steering controls outward to the locked (outer) neutral position. Place controls in neutral position 8061-026 Move the throttle to the middle position. Set the throttle 8052-001 If the engine is cold, the choke control should be pulled up.
operation Press in and turn the ignition key to the start position. Turn to the start position 8050-7432 When the engine starts, immediately release the ignition key back to the run position. IMPORTANT INFORMATION Do not run the starter for more than 5 seconds each time. If the engine does not start, wait approximately 10 seconds before retrying. Return to run position 8050-7432 Set the desired engine speed with the throttle.
operation Weak Battery WARNING! Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. IMPORTANT INFORMATION Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles. If your battery is too weak to start the engine, it should be recharged. (See “Battery” in the Maintenance Section.
operation Running 1. Release the parking brake by pushing the button and moving the lever downward. NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. 2. Move the steering controls to the neutral position (N). Parking brake released 8058-020 3. Set retaining pin into selected cutting height and secure the opposite side with a cotter hairpin.
operation 6. Engage the mower deck by pulling out the blade switch. 7. Move throttle control to full throttle. The machine’s speed and direction are continuously variable using the two steering controls. When both controls are in the neutral position, the machine stands still. By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.
operation Mowing Tips • • • • • • • • Observe and flag rocks and other fixed objects to avoid collisions. Begin with a high cutting height and reduce it until the desired mowing result is attained. The average lawn should be cut to 2½" (64 mm) during the cool season and over 3" (76 mm) during the hot months. For healthier and better looking lawns, mow often after moderate growth. For best cutting performance, grass over 6" (15 cm) in height should be mowed twice.
operation Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling. • Disengage the mower deck by depressing the blade switch. Disengage the mower deck and move throttle to minimum • 8052-001 Raise the mower deck by pressing the button on the lever and pulling backward to the transport position.
operation Manual Transport ZT-2800 Bypass Linkages When pushing or pulling the mower, engage the ZT-2800 (Integrated Zero turn Transaxle) bypass linkages. The ZT-2800 bypass linkages are located on the rear of the frame, below the rear engine guard. 1. Raise the deck into the highest cutting position. 2. Pull the ZT-2800 bypass linkages up and out of the keyhole slots. Release the levers with the head outside the frame and held in the bypass position. 3.
MAINTENANCE Maintenance Schedule The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation. Read “Maintenance” in the Safety Instructions section. 1) First change after 5-8 hours.
MAINTENANCE Maintenance Daily Before After Wkly At least once each year Maintenance interval in hours 25 50 100 ● ■ ● Check/adjust throttle cable ● ■ ■ ■ ● ■ Check the condition of belts, belt pulleys Change the engine oil 1) Replace the engine oil filter Clean/replace the spark plugs Replace the fuel filter Replace the air filter (paper filter) 2) ■ ■ ● ■ ● Check the caster wheels (every 200 hours) ■ ● ■ ♦ Replace the air cleaner’s pre-filter 2) (foam) Check/adjust the mower deck Check the e
MAINTENANCE Battery STANDARD Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life. • • • BATTERY STATE OF CHARGE 12.6V APPROXIMATE BATTERY CHARGING TIME* TO FULL CHARGE AT 80OF / 27OC 100% Maximum Rate at: 50 Amps 30 Amps 20 Amps 10 Amps - FULL CHARGE - 12.4V 75% 20 min. 35 min. 48 min. 90 min. 12.2V 50% 45 min. 75 min. 95 min. 180 min.
MAINTENANCE Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: 1. The mower deck is disengaged. 2. The steering controls are in the outer, locked neutral position. 3. The parking brake is on. Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again.
MAINTENANCE Fuel Pump Air Filter Regularly check that the fuel pump’s air filter is free from dirt. Remove the screws and open the pump, no hoses need be removed. The filter can be cleaned with a brush if necessary. Replace the filter on the console. WARNING! Faulty adjustment will result in reduced braking ability and can cause an accident. Parking Brake Visually check that no damage is found on the lever, cables, or switch belonging to the parking brake.
MAINTENANCE V-belts Check every 100 hours of operation. Check for severe cracking and large nicks. NOTE: The belt will show some small cracks in normal operation. The belts are not adjustable. Replace belts if they begin to slip from wear. Deck Belt Removal 1. Park on a level surface. Apply parking brake. 2. Lower the deck into the lowest cutting position. 3. Remove bolts from belt shields and remove shields. 4.
MAINTENANCE Pump Belt Replacing pump belt Park the mower on a level surface. Engage the parking brake. Belt removal 1. Remove the deck belt (see Deck Belt Removal in this section of the manual). 2. Create slack in the belt by removing the spring on the pump idler arm. 3. The belt should now be able to be removed from the engine pulley and pump pulleys. Belt installation 1. Wrap the belt around the pulley 2. Route the belt around the inside of the idler pulley. 3. Wrap the belt around the engine pulley. 4.
MAINTENANCE Cutting Blades In order to attain the best mowing effect, it is important that the blades are well sharpened and not damaged. Bent or cracked blades or blades with large nicks should be replaced. IMPORTANT INFORMATION The sharpening of blades should be carried out by an authorized service workshop. Damaged blades should be replaced when hitting obstacles that result in a breakdown. Let the service workshop decide whether the blade can be repaired/ ground or must be replaced.
MAINTENANCE Adjusting the Mower Deck Leveling deck Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to the correct pressure. See “Technical Data” under Transmission. If tires are under or over inflated, the deck cannot be properly adjusted. The deck should be adjusted slightly higher in the rear. NOTE: To insure accuracy of leveling procedure, mower deck drive belt must be installed prior to leveling deck. 1. Wear heavy gloves.
MAINTENANCE Anti-Scalp Rollers Anti-scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position. Antiscalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions. IMPORTANT INFORMATION Adjust anti-scalp rollers with the mower on a flat level surface.
MAINTENANCE Cleaning Regular cleaning and washing, especially under the mower deck, will increase the machine’s life-span. Make it a habit to clean the machine directly after use (after it is cooled), before the dirt sticks. Do not spray water on the top of the mower deck. Use compressed air to clean the top side of mower deck. Regularly clean deck and underside of the deck with normal water pressure. Do not use a high pressure washer or steam cleaner.
LUBRICATION 8050-832 12/12 Every year Lubricate with grease gun 1/52 Every Week Oil change 1/365 Every day Filter change Lubricate with oil can Level check * Change transmission filter General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil. When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.
LUBRICATION Front Wheel Mount Lubricate with a grease gun, one zerk for each wheel mount, until the grease is forced out. Use only good quality bearing grease. Grease from well-known brand names (petrochemical companies) usually maintains a good quality. Front Wheel Bearings Lubricate with a grease gun, one zerk for each set of wheel bearings, until the grease is forced out. Use only good quality bearing grease.
LUBRICATION Transaxle (Transmission) Fluid Change This transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality levels and longer life, an oil filter change interval of every 200 hours is recommended. The following procedure is performed with the transaxles installed in the mower and the mower on level ground. Apply the pump release valve for each transaxle and set the parking brake. 1. Remove the three ¼" filter guard screws and filter guard.
LUBRICATION Purging Due to the effects air has on efficiency in hydrostatic drive applications, it is critical to purge the system. These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional oil has been added to the system. Resulting symptoms in hydrostatic systems may be: 1. Noisy operation. 2. Lack of power or drive after short term operation. 3. High operation temperature and excessive expansion of oil. 4.
TROUBLESHOOTING Problem Cause Engine will not start • Blade switch is engaged. • Steering controls are not locked in the neutral position • Parking brake is not activated • Battery is dead • Contamination in the carburetor or fuel line.
TROUBLESHOOTING Problem Cause Engine overheats • Clogged air intake or cooling fins • Engine overloaded • Poor ventilation around engine • Defective engine speed regulator • Too little or no oil in the engine • Contamination in the carburetor or fuel line.
STORAGE Winter Storage At the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days). Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function. Fuel stabilizers are an acceptable option as regards to the sticky residues that can occur during storage. Add stabilizer to the fuel in the tank or in the storage container.
schematics 52
TECHNICAL DATA Accessories Collection system Torque Specifications Engine crankshaft bolt Deck pulley bolts Lug nuts Blade bolt Standard ¼" fasteners 50 ft/lb (67 Nm) 150 ft/lb (203 Nm) 75 ft/lb (100 Nm) 90 ft/lb (122 Nm) 9 ft/lb (12 Nm) Standard 5/16" fasteners Standard 3/8" fasteners Standard 7/16" fasteners Standard ½” fasteners 18 ft/lb (25 Nm) 33 ft/lb (44 Nm) 52 ft/lb (70 Nm) 80 ft/lb (110 Nm) HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specific torque v
TECHNICAL DATA EZ4824K / 966038201 EZC4824 BF / 966047501 Kohler Kohler Type Courage Courage Power 24 hp 24 hp (1, 2 Engine Manufacturer Lubrication (1, 2 Pressure with oil filter Pressure with oil filter Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) 4 gallons / 15.1 liters 4 gallons / 15.
TECHNICAL DATA EZ4824 / 966038201 EZC4824 BF / 966047501 Cutting Width 48" / 122cm 48" / 122cm Cutting Height 1½ - 4" / 3.8 - 10.2 cm 1½ - 4" / 3.8 - 10.
TECHNICAL DATA EZ5224 / 966038301, EZ5224BF / 966495901 Engine Manufacturer Kohler Type Courage Power 24 hp (1,2 Lubrication Fuel Fuel tank capacity Pressure with oil filter Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) 4 gallons / 15.1 liters Cooling Air cooled Air filter Standard Alternator 12V Starter Electric Transmission Transmission Speed and direction controls ZT2800 Hydro Gear Dual levers, foam gripped Speed forward 0-7 mph / 0-11.3 km/h Speed reverse 0-3.5 mph / 0-5.
TECHNICAL DATA EZ5224 / 966038301, EZ5224BF / 966495901 Frame Cutting Width 52" / 132cm Cutting Height 1½ - 4" / 3.8 - 10.2 cm Uncut Circle 0 Number of Blades 3 Blade Length 18" / 45.7 cm Nose Rollers Yes Sprung Seat Standard Hinged Arm Rests Standard Hour Meter Standard Blade Engagement Electromagnetic clutch Deck Construction 11 gauge w/ 10 gauge skirts Productivity 3.
CONForMITY CERTIFICATES USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove any of these labels. Certificates can also be supplied with the machine at delivery or written in the Engine manual. Take care of them as they are valuable documents.
SERVICE JOURNAL Action Date, mtr reading, stamp, sign Delivery Service Charge the battery. Adjust the tire pressure of all wheels to 15 PSI (1 bar). Mount the steering controls in the normal position. Connect the contact box to the cable for the seat’s safety switch. Check that the right amount of oil is in the engine. Adjust the position of the steering controls. Fill with fuel and open the fuel shut off valve. Start the engine. Check that there is drive to both wheels. Check the mower deck adjustment.
SERVICE JOURNAL Action Date, mtr reading, stamp, sign After the first 5-8 hours Change the engine oil. q 25-Hour Service Check the engine air filter. Sharpen/Replace mower blades if required. Check the tire pressures. Check battery cables. Lubricate according to lubrication chart. Check/clean the engine’s cooling air intake. Clean the air cleaner’s pre-filter (foam).
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 50-Hour Service Perform the 25-hour service. Clean/replace the air cleaner’s filter cartridge (paper filter (shorter intervals for dusty operating conditions). Change engine oil. Lubricate according to lubrication chart. Check/adjust the parking brake. q q q q q 100-Hour Service Perform the 25-hour service. Perform the 50-hour service. Change the engine oil filter. Clean/replace the spark plugs. Replace the fuel filter. Check V-belts.
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 300-Hour Service Perform the 25-hour service. Perform the 50-hour service. Perform the 100-hour service. Check/adjust the mower deck. Clean the combustion chamber and grind the valve seats. Check the engine valve clearance. Replace the air cleaner’s pre-filter (foam). q q q q q q q At Least Once Each Year Clean the engine’s cooling air intake (25 hours). Replace the air cleaner’s pre-filter (foam) (300 hours).
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 63
SERVICE JOURNAL Action 64 Date, mtr reading, stamp, sign
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 65
P/N 115 387527R1 06/01/10