6 2 Z Q H U V 0 D Q X D O +89 * +89 ( +89 *;3 $1' +89 (;3 8WLOLW\ 9HKLFOHV
NOTICE The Husqvarna® Limited Two Year Warranty for 2006 Transportation and Utility Vehicles and California Emission Control Warranty Statement appear on the last pages of this manual. No other warranties, express or implied, are contained herein. Please complete and return the warranty registration card included in this manual. Husqvarna is not liable for errors in this manual or for incidental or consequential damages that result from the use of the material in this manual.
FOREWORD Thank you for choosing Husqvarna, a world leader in outdoor products. You have chosen the finest utility vehicle on the market. Please protect your investment and ensure that your Husqvarna vehicle provides years of reliable, superior performance by reading and following the maintenance instructions in this manual. Your comfort and safety are important to us, so we urge you to read and follow the step-by-step operating instructions and safety precautions in this manual.
TABLE OF CONTENTS Vehicle Feature Identification .................................................................................................................... 4 Safety Details ............................................................................................................................................ 9 General Warnings ...................................................................................................................................... 9 General Information ......
Vehicle Feature Identification HUV4210-E ELECTRIC VEHICLE BATTERY DANGER DECAL (ON BATTERY CAPS OR ON BODY UNDER SEAT) ELECTRICAL COMPONENT DECAL (ON SPEED CONTROLLER COVER) TOW SWITCH WARNING DECAL (ON TOW SWITCH BRACKET UNDER SEAT) SERVICE NOTICE DECAL (ON BODY UNDER BED) CHARGER RECEPTACLE FORWARD/REVERSE SWITCH Page 4 2006 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual
Vehicle Feature Identification HUV4210-E ELECTRIC VEHICLE ! WARNING ROLLOVER OR FALLING OFF MAY CAUSE SERIOUS INJURY OR DEATH • Before using vehicle, read operating instructions. • Remain seated while moving. • Do not start vehicle until all occupants are seated. • Hold on to seat handle while moving. • Operate from driver side only and not on public roads. • Two (2) persons per seat maximum. • Drive slowly in turns and straight up and down slopes. • Never stand in front of or behind vehicle.
Vehicle Feature Identification HUV4210-G GASOLINE VEHICLE OPERATING INSTRUCTIONS ! • Read owner’s manual and dash-mounted safety warnings prior to driving. • Study and understand controls. WARNING ROLLOVER OR FALLING OFF MAY CAUSE SERIOUS INJURY OR DEATH TO START ENGINE • Place shift lever in “N” – Neutral position. • Press brake pedal. • Turn key switch to “START position and release. • Before using vehicle, read operating instructions. • Do not start vehicle until all occupants are seated.
Vehicle Feature Identification HUV4210-G GASOLINE VEHICLE GASOLINE WARNING DECAL (ON VEHICLE FRAME NEAR FUEL TANK) OIL FILL ROTATING PARTS AND HOT MANIFOLD DECAL FUEL SHUT-OFF VALVE (ON STARTER/GENERATOR) F N R FORWARD/REVERSE HANDLE DIODE WIRING DECAL CHOKE FRAME GROUND AND GOVERNOR WARNING DECAL (ON VEHICLE FRAME NEAR BATTERY) 2006 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual Page 7
Practice Safety ! WARNING Rotating Parts Safety signs like you see above may at first seem shocking, but their impact is mild compared with the reality of severe personal injury. Your safety and satisfaction are of the utmost importance to Husqvarna. That is why before operating the vehicle, we urge you to review the information in this manual.
Safety Details SAFETY DETAILS ý WARNING • This owner’s manual should be read completely before attempting to drive or service the vehicle. Failure to follow the instructions in this manual could result in property damage, severe personal injury, or death. It is important to note that some vital statements throughout this manual and on the decals affixed to the vehicle are preceded by the words DANGER, WARNING, or CAUTION.
General Warnings ý DANGER • Do not operate gasoline vehicle in an enclosed area without proper ventilation. The engine produces carbon monoxide, which is an odorless, deadly poison. • A Husqvarna vehicle will not provide protection from lightning, flying objects, or other stormrelated hazards. If caught in a storm while driving a Husqvarna vehicle, exit the vehicle and seek shelter in accordance with applicable safety guidelines for your location.
General Information ý WARNING • Use insulated tools when working near batteries or electrical connections. Use extreme caution to avoid shorting of components or wiring. All vehicles: • Wear safety glasses or approved eye protection when servicing the vehicle or battery charger. Wear a full face shield and rubber gloves when working on or near batteries. • Do not wear loose clothing or jewelry such as rings, watches, chains, etc., when servicing the vehicle or battery charger.
Model Identification Figure 3 Bumper Figure 4 Brush Guard MODEL IDENTIFICATION The serial number of the vehicles are printed on two bar code decals. (Example: HH0601-583947) (Figure 5). One is mounted on the frame, under the bed, on the passenger side. There is also a second serial number decal mounted on the front frame behind the dash. The dash must be removed to view this decal. See following NOTE. NOTE: Have the vehicle serial number available when ordering parts or making inquiries.
Controls and Indicators CONTROLS AND INDICATORS See General Warnings on page 9. ý WARNING • If renting or loaning the vehicle, make sure the driver is familiar with all controls and operating procedures before allowing the vehicle to be driven. • Do not shift the Forward/Reverse handle or switch while the vehicle is moving. To avoid injury to an unsuspecting passenger or damage to the vehicle, always bring the vehicle to a full stop before shifting the Forward/Reverse handle or switch.
Controls and Indicators NOTE: The key can be removed only when the key switch is in the OFF position. GAS VEHICLE SHOWN Figure 6 Key Switch Electric Vehicles The key switch is mounted on the dash to the right of the steering column. It has two positions, OFF and ON, which are clearly labeled. See following NOTE. NOTE: The key can be removed only when the key switch is in the OFF position.
Controls and Indicators F R Figure 7 Forward/Reverse Handle – Gas Vehicle Figure 8 Forward/Reverse Rocker Switch – Electric Vehicle Figure 9 Accelerator and Brake Pedals ACCELERATOR PEDAL The accelerator pedal is the pedal on the right, with the word GO molded into it (Figure 9). Electric Vehicles The operation of the accelerator pedal differs from that of an automobile.
Controls and Indicators BRAKE PEDAL The brake pedal is the large pedal on the left with the word STOP molded into it (Figure 9). To slow or stop the vehicle, press the brake pedal with your foot (Figure 10). Figure 10 Brake Pedal Figure 11 Park Brake Pedal PARK BRAKE PEDAL The park brake pedal is the small raised portion in the upper left corner of the brake pedal. It has the word PARK molded into it and the words PARK BRAKE marked on top of it (Figure 10).
Controls and Indicators • The warning light will not illuminate if the charge is 90% or more complete. The onboard computer will retain in memory the amount of charge needed to fully replenish the batteries and will complete the charge during the next charge cycle. • When the charger is unplugged, the warning light will illuminate and remain illuminated for 10 seconds if the charge is less than 90% complete but the vehicle has enough power for approximately 30 minutes of operation.
Controls and Indicators NING WAR TOW RUN F Figure 12 Tow/Run Switch CHOKE Gasoline Vehicles Only The choke is located on the seat support panel below and to the left of the driver’s left knee (Figure 13). If the vehicle is hard to start in cool or cold temperatures, simply push in the choke cover to activate it. Hold it during start up and release the choke cover after the engine starts and runs smoothly.
Pre-Operation and Daily Safety Checklist CAUT ION • Failure to add oil immediately when the low oil warning light stays on may result in permanent engine damage. HEADLIGHT CONTROL The headlight control (2) is located on the dash to the left of the key switch (Figure 14). Pull out to turn the lights on, push in to turn the lights off. The headlights operate on 12 volts DC from the battery. See following NOTE.
Pre-Operation and Daily Safety Checklist • Charger cord, plug, and receptacle (electric vehicles): Visually inspect for cracks, loose connections, and frayed wiring. See Plug and Receptacle on page 38. • Engine (gasoline vehicles): Check for proper engine oil level. See Engine Oil – Gasoline Vehicles on page 41. • Fuel (gasoline vehicles): Check fuel level. See Fueling Instructions – Gasoline Vehicles on page 44. Check fuel tank, lines, cap, pump, fuel filters, and carburetor for fuel leakage.
Driving Instructions ý WARNING • Zero-speed detect will not limit vehicle speed to 1 mph (1.6 km/h) on very steep grades. Do not operate vehicle on slopes exceeding 20% grades. • Pedal Up Motor Braking (adjustable on IQ System vehicles): Accelerate the vehicle to full speed and then release the accelerator pedal. Motor braking should quickly and smoothly slow the vehicle to approximately 11 mph (17.7 km/h). Motor braking will disengage when vehicle slows to 11 mph (17.7 km/h).
Driving Instructions ý WARNING • To help avoid possible injury to an inattentive passenger and (or) damage to the vehicle, avoid sudden starts, sudden stops, and abrupt turns. • To help avoid the possibility of losing control of or overturning the vehicle, reduce speed for adverse driving conditions such as wet grass or rough terrain. • Do not use the vehicle on public roads. It is not designed or intended for street use and should not be licensed for use on public roads. • Obey all local rules.
Driving Instructions 5. Turn the key all the way to the START position and hold, activating the choke as necessary, until the engine is running smoothly. The engine will idle in neutral. 6. Select direction by placing the Forward/Reverse handle in desired position (F = forward or R = reverse). A buzzer will sound as a warning when the Forward/Reverse handle is in the REVERSE position. 7. Slowly press accelerator pedal. The park brake will release automatically and the vehicle will start to move.
Bed Latch BED LATCH See General Warnings on page 9. The bed latch (1) is located under the front corners of the bed (Figure 15, Page 24) and engages automatically when the bed is closed. To lift the bed, pull the bed latch toward the side of the vehicle and lift the bed. To close the bed gently lower the bed to a closed position. DO NOT drop the bed. See following WARNING. ý WARNING • Keep hands and fingers clear of crush area between the bed and the seat back support.
Storage – Electric Vehicles If the vehicle must be transported over long distances or on public highways, it should be transported on an approved trailer that has the approved load rating of 1200 lb. (544 kg) per vehicle being transported. See following NOTE. NOTE: A two-car trailer should be rated at 2 x 1200 = 2400 lb. (2 x 544 = 1088 kg). STORAGE – ELECTRIC VEHICLES See General Warnings on page 9.
Storage – Gasoline Vehicles RETURNING THE STORED ELECTRIC VEHICLE TO SERVICE 1. If necessary, connect batteries and tighten terminals to 110 in-lb (12.4 N·m). 2. Fully charge batteries. 3. Adjust tires to recommended tire pressure. See Vehicle Specifications on page 46. 4. Perform the Pre-Operation and Daily Safety Checklist on page 19. STORAGE – GASOLINE VEHICLES See General Warnings on page 9. ý DANGER • Do not attempt to drain gasoline when the engine is hot or while it is running.
Storage – Gasoline Vehicles 2.4. Plug the fuel tank vent nipple so that it is air tight. We recommend using a slip-on vinyl cap. 3. Disconnect the battery cables, negative (–) cable first. 4. Batteries should be clean and free of corrosion. Wash tops and terminals of batteries with a solution of baking soda and water (1 cup (237 mL) baking soda per 1 gallon (3.8 L) of water). Rinse solution off batteries. Do not allow this solution to enter the batteries. Be sure terminals are tight.
Maintenance RETURNING THE STORED GASOLINE VEHICLE TO SERVICE 1. Restore fuel system to operation (Figure 32, Page 45). 1.1. Remove plug from fuel tank vent. 1.2. Connect vent tube to fuel tank vent. 2. Connect battery cables, positive (+) cable first, and tighten terminals to 12 ft-lb (16 N·m). 3. Completely open the fuel shut-off valve (Figure 17). Make sure the valve is fully open.
Periodic Service Schedules ý WARNING Gasoline vehicles only: • Moving parts: Do not attempt to service gasoline vehicle while the engine is running. • Hot! Do not attempt to service hot engine or exhaust system. Failure to heed this warning could result in severe burns. • Turn the fuel shut-off valve to the closed (OFF) position (Figure 16, Page 27).
Periodic Service Schedules PERIODIC SERVICE SCHEDULE – ELECTRIC VEHICLES REGULAR INTERVAL SERVICE Daily service by owner Batteries Charge batteries (after each use only). Weekly service by owner Batteries Check electrolyte level. Add water if necessary. See page 35. Monthly service by owner or trained technician Batteries Wash battery tops and clean terminals with baking soda/water solution. Tires Check air pressure and adjust if necessary. See Vehicle Specifications on page 46.
Periodic Service Schedules PERIODIC SERVICE SCHEDULE – GASOLINE VEHICLES REGULAR INTERVAL SERVICE Monthly service by owner or trained technician Check engine oil level; change if necessary. See Periodic Lubrication Schedules on page 32. Engine Semiannual service by trained technician only (or every 50 hours of operation, whichever comes first) Check engine cooling air intake; clean if necessary. Visually inspect the unshrouded area around engine exhaust for grass and debris, and clean if necessary.
Periodic Lubrication Schedules PERIODIC LUBRICATION SCHEDULES PERIODIC LUBRICATION SCHEDULE – ELECTRIC VEHICLES REGULAR INTERVAL LUBRICATION POINTS SERVICE Semiannually by owner or trained technician (or every 50 hours of operation, whichever comes first) Annually by trained technician only (or every 100 hours of operation, whichever comes first) RECOMMENDED LUBRICANT Brake pedal shaft bearings 1 Dry Moly Lube (Husqvarna 603 00 0001) Brake linkage and pivots 2 Dry Moly Lube (Husqvarna 603 00 00
Periodic Lubrication Schedules PERIODIC LUBRICATION SCHEDULE – GASOLINE VEHICLES REGULAR INTERVAL LUBRICATION POINTS SERVICE Semiannually by owneror trained technician (or every 50 hours of operation, whichever comes first) RECOMMENDED LUBRICANT Brake pedal shaft bearings 1 Dry Moly Lube (Husqvarna 603 00 0001) Brake linkage and pivots 2 Dry Moly Lube (Husqvarna 603 00 0001) Accelerator push rod pivots, mounts, and shifter cable pivots 3 Dry Moly Lube (Husqvarna 603 00 0001) Front suspension
Vehicle Controller – Electric Vehicles VEHICLE CONTROLLER – ELECTRIC VEHICLES The electric vehicle is equipped with a solid state speed controller. In order to properly service and maintain the solid state controller vehicle, it is necessary to understand the electrical circuitry and the functions of all components in both systems. Therefore, if any repair or servicing needs to be performed, we recommend that it be performed by an authorized Husqvarna distributor/dealer using Husqvarna parts.
Batteries – Electric Vehicles 1. The batteries should be kept clean and free of corrosion. Wash tops and terminals of batteries with a solution of baking soda and water (1 cup (237 mL) baking soda per gallon (3.8 L) of water). Rinse solution off of the batteries. Do not allow this solution to enter the battery. Be sure terminals are tight. Let the terminals dry and then coat with Battery Terminal Protector Spray (Husqvarna 603 00 00-03). See following NOTE. NOTE: Dispose of waste water properly. 2.
Battery Charger – Electric Vehicles BATTERY CHARGER – ELECTRIC VEHICLES ý DANGER • The charging area must be ventilated. Hydrogen level in the air must never exceed 2%. The total volume of air in the charging area must be changed five times per hour. Exhaust fans should be located at the highest point of the roof. Contact a local HVAC engineer. • Do not charge the vehicle batteries with the vehicle covered or enclosed.
Battery Charger – Electric Vehicles NOTE: Because the vehicle’s onboard computer (OBC) has a storage charge feature that automatically checks and recharges the batteries as necessary every 15 days, the charger can remain plugged to an electric vehicle throughout the storage period. Shortly after charging begins, the PowerDrive 2 Charger will shut off in order to run a self-diagnostic program (ammeter will drop to zero). Charging will resume in a few moments (ammeter returns to previous rate of charge).
Battery Charger – Electric Vehicles NOTE: When temperatures fall below 65 °F (18.3 °C), batteries charged in unheated areas should be placed on charge as soon as possible after use. Batteries are warmest immediately after use, and cold batteries require more time to fully charge. Insert the charger DC plug into the vehicle receptacle. The charger will turn on two to ten seconds later (Figure 22).
Battery – Gasoline Vehicles 48-VOLT FUSE LINK SENSE LEAD FUSE ! N DA R/ GE N ISO PO Figure 24 Receptacle Fuse Link RECEPTACLE FUSE LINK As an additional feature to protect the batteries and charging circuit from an overload, the electric vehicle is equipped with a receptacle fuse link (Figure 24) . If the charger does not come on when the vehicle is placed on charge, visually inspect the fuse link. See following WARNING.
Battery – Gasoline Vehicles ý DANGER - External: Flush with water. Call a physician immediately. - Internal: Drink large quantities of milk or water followed with milk of magnesia or vegetable oil. Call a physician immediately. - Eyes: Flush with water for 15 minutes. Call a physician immediately. ý WARNING • Do not jump start a dead battery using another battery and jumper cables.
Engine Oil – Gasoline Vehicles ENGINE OIL – GASOLINE VEHICLES See General Warnings on page 9. Even though the low oil warning light on the dash should illuminate if oil level becomes low, engine oil level should be checked monthly. Vehicle should be on a level surface when checking oil. Do not overfill with oil. ENGINE OIL LEVEL CHECK 1. Remove the oil level dipstick from the oil filler tube and wipe oil from dipstick (Figure 27). See following CAUTION.
Engine Oil – Gasoline Vehicles 3. Disconnect the battery cables, negative (–) cable first . See WARNING “To avoid unintentionally starting...” on page10. 4. Position a pan designed for oil changes under the front drain plug (Figure 28). 5. Use a 14 mm socket or box end (do not use an open end) wrench to remove the drain plug, turning it counterclockwise, and allow the engine oil to drain into the pan. See following WARNING.
Engine Oil – Gasoline Vehicles 10. Use a clean rag and wipe the oil filter mounting bracket surface clean where the oil filter gasket seats. 11. Install a new oil filter (Husqvarna 603 00 00-06) onto the engine oil filter port. Apply a light coat of white lithium NLGI Number 2 grease (Dow Corning® BR2-Plus or equivalent) or new engine oil to the rubber seal around the outside surface of the filter before attaching it to the oil filter port (Figure 30).
Fueling Instructions – Gasoline Vehicles -20° C -10°C 0 °C 10° C 20° 30°C 40°C SAE 40 SAE 30 SAE 10W-30/SAE 10W-40 ° SAE 5W-20 -4°F 14 °F 32°F 50 ° F 68°F 86° F 104°F Figure 31 Oil Viscosity Chart FUELING INSTRUCTIONS – GASOLINE VEHICLES See General Warnings on page 9. ý DANGER • Turn the key switch to the OFF position before fueling. • Do not pour gasoline into the fuel tank when the engine is hot or while it is running.
Cleaning the Vehicle VENT SHUT-OFF VALVE VENT TUBES Figure 32 Fuel Tank CLEANING THE VEHICLE Husqvarna vehicles are equipped with ABS front bodies and TPO for rear bodies. Use only commercially available automotive cleaners with a sponge or soft cloth for normal cleaning. A garden hose at normal residential water pressure is adequate. Husqvarna does not recommend any type of pressure washing or steam cleaning.
Vehicle Specifications VEHICLE SPECIFICATIONS SPECIFICATIONS Electric HUV4210EXP Electric HUV4210-E Gasoline HUV4210GXP Gasoline HUV4210-G POWER SOURCE Drive motor: Direct drive, 48 volts DC, shunt-wound, 3.2 hp • Engine: 4-cycle OHV, 286 cc, 9.0 hp rated, single-cylinder, air-cooled, with pressure lubrication system • Engine: 4-cycle OHV, 351cc, 11.
Vehicle Specifications SPECIFICATIONS Electric HUV4210-E Electric HUV4210EXP Standard seating capacity Gasoline HUV4210-G Gasoline HUV4210GXP 2 LIQUID CAPACITIES Transaxle 22 oz. (0.67 L) Engine crankcase (without filter) 32 oz. (0.95 L) Engine crankcase (with filter) 38 oz. (1.12 L) Unitized transaxle 27 oz. (0.8 L) Fuel tank 7 gallons (26.5 L) TIRE PRESSURE Front and rear 18-20 psi (1.24-1.38 Bars) 18-20 psi (1.24-1.
HUSQVARNA® LIMITED TWO YEAR WARRANTY FOR 2006 TRANSPORTATION AND UTILITY VEHICLES 1. WARRANTY: HUSQVARNA, INC.
6. DISCLAIMER: THIS LIMITED WARRANTY IS EXCLUSIVE. HUSQVARNA MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS OR TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY HUSQVARNA AND EXCLUDED FROM THIS WARRANTY. THE PURCHASER AND HUSQVARNA EXPRESSLY AGREE THAT THE REMEDY OF THE REPLACEMENT OR REPAIR OF THE DEFECTIVE VEHICLE OR COMPONENT THEREOF IS THE SOLE REMEDY OF THE PURCHASER.
battery, a prudent owner will read and study the charger owner's manual, the electric vehicle owner's manual, the operator instructions, and the battery warning labels; and will exercise due care in working on or around batteries. Transportation expenses for warranty services are also excluded from this warranty. WARRANTY LIMITATIONS HUSQVARNA's liability under this limited warranty shall be to replace a defective battery.
Any warranty service, which includes labor during the first year, must be performed by HUSQVARNA or by an authorized distributor or dealer. For repairs made by qualified technicians other than HUSQVARNA's factory technicians or an authorized distributor or dealer, HUSQVARNA will provide only the replacement parts or components.
Free replacement with respect to parts and labor within four years or 16,000 energy units as recorded by the Computer, whichever first occurs, from date of purchase. The vehicle should be returned to an authorized HUSQVARNA distributor or dealer with evidence of proof of purchase date. HUSQVARNA reserves the right to test any Computer returned for warranty and to verify number of energy units by accessing information contained in the Computer.
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT Your new Husqvarna, Inc. ("HUSQVARNA") vehicle engine complies with both the U.S. EPA and State of California emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The California Air Resources Board ("CARB") and HUSQVARNA are pleased to explain the emission control system warranty on your 2006 vehicle engine. In California, new small offroad engines (SORE) must be designed, built and equipped to meet the State's stringent anti-smog standards.
0UBLICATION 0ART .UMBER 603 00 23-77 %DITION #ODE 0705B0705A (USQVARNA &OREST AND 'ARDEN 3TATESVILLE 2D #HARLOTTE .
