56 030 OWNER’S MANUAL Model Number H346SL Product No. 960 73 00-12 (MFG. ID. No. 96073001200) 46 Inch Mower Grass Catcher • • • • 532413532 03.05.07 BY Assembly Operation Customer Responsibilities Repair Parts Printed in U.S.A.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IV. TOWING • • • • • • Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes. Never allow children or others in or on towed equipment. On slopes, the weight of the towed equipment may cause loss of traction and loss of control. Travel slowly and allow extra distance to stop.
KNOW YOUR GRASS CATCHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCHER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. Save this manual for future reference.
ASSEMBLY 1 BAGGER SUPPORT (See Fig. 1) 2 ASSEMBLY 1. Remove and discard the upper bolt on both sides of the drawbar. Using the same holes, install the shoulder bolts supplied and tighten securely. 2. Align support assembly pin with hole in drawbar and hang assembly over the shoulder bolts. 3. Be sure support assembly is seated properly and secure with retainer spring supplied. MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig.
3 4 CONTAINER MOUNTING (See Fig. 3) 1. Install one container to left side first. Install another container to center position and one in right position. NOTE: Left edge of right container should always overlap right edge of left container at center supports. 2. Close cover and lock latches over center support tubes. To lock and release latches, pull back on latch handles. LOWER CHUTE - MOWER WITH MOUNTING TAB (See Fig. 4) 1. Raise and hold deflector shield in upright position. 2.
5 6 UPPER CHUTE (See Figs. 5A and 5B) 1. Lower mower to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. TIP: Holding upper chute as shown and twisting while installing in cover will help keep the rubber seal in place. NOTE: Handle carefully so as not to damage full bag indicator. COVER • UPPER CHUTE FIG. 6A 3. Push in and turn upper chute until it is in line with lower chute. 4.
OPERATION TIPS FOR IMPROVED BAGGING OPERATION: • Your bagger is equipped with a full bagger indicator. Movement of the wheel increases as the bags fill. The wheel will be spinning fastest just before the bags fill completely. When the wheel stops, it indicates that the bags are full and the chutes have become clogged. NOTE: To help prevent clogging of chutes, check/empty bags when the wheel is spinning fast. Experience will teach you the best time to empty the bags.
CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS CAUTION: Grass catcher components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended parts, when necessary. Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. BLADE CARE For best results mower blades must be kept sharp.
REPAIR PARTS GRASS CATCHER - MODEL NUMBER H346SL (PRODUCT NO. 960 73 00-12) 4 5 6 7 8 10 2 9 12 13 9 11 14 2 18 38 20 15 38 20 34 15 9 20 12 37 14 3 20 33 26 32 31 35 33 31 29 28 29 30 KEY NO. PART NO.
SECTION 1: LIMITED WARRANTY WARRANTY STATEMENT Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: Lifetime Warranty (Parts and Labor): All tiller tines and trimmer shafts against breakage. Proof of purchase required.