Operator′s manual Manual d’utilisation Manual de instrucciones Hedge Trimmer Attachment HA 110 HA 850 Complément Taille-haie HA 110 HA 850 Tijeras cortasetos (suplemento) HA 110 HA 850 .
KEY TO SYMBOLS Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Noise emission to the environment according to the European Community’s Directive.
CONTENTS Contents KEY TO SYMBOLS Symbols ....................................................................... CONTENTS Contents ...................................................................... Note the following before starting: ................................ SAFETY INSTRUCTIONS Machine′s safety equipment ........................................ Checking, maintaining and servicing the machine′s safety equipment ..........................................................
SAFETY INSTRUCTIONS Machine′′s safety equipment This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine.
SAFETY INSTRUCTIONS Blade guard Safety instructions regarding the surroundings (HA 110) • Check that the blade guard is not damaged or distorted. • Replace the blade guard if it is bent or damaged. • Never allow children to use the machine. • Ensure that no-one comes closer than 15 m while you are working. • Never allow anyone else to use the machine without first ensuring that they have understood the contents of the operator’s manual.
SAFETY INSTRUCTIONS • Do not cut too close to the ground. Stones and other objects can be thrown out. • Check the working area for foreign objects such as electricity cables, insects and animals, etc, or other objects that could damage the cutting attachment, such as metal items. • If any foreign object is hit or if vibrations occur stop the machine immediately. Disconnect the HT lead from the spark plug. Check that the machine is not damaged. Repair any damage.
WHAT IS WHAT? 4 7 2 1 2 2 3 11 6 12 9 5 8 10 What is what on the hedge trimmer attachment? (HA 110) 1 Cutter 7 Angle adjustment knob 2 Grease nipples (3) 8 Hand guard 3 Bevel gear 9 Operator′s manual 4 Blade guard 10 Transport guard 5 Front handle 11 Shaft coupling 6 Hand guard mounting screw 12 Shaft (110 mm) English –7
WHAT IS WHAT? 6 2 1 2 2 10 3 9 4 5 7 8 What is what on the hedge trimmer attachment? (HA 850) 1 Cutter 6 Angle adjustment knob 2 Grease nipples (3) 7 Operator′s manual 3 Bevel gear 8 Transport guard 4 Front handle 9 Shaft coupling 5 Shaft (829 mm) 10 Handle 8 – English
ASSEMBLY Fitting the hand guard and loop handle (HA 110) 1 2 Loosen the clutch sleeve’s two mounting bolts and dismantle the clutch sleeve. Fitting the cutting head It is important that the hedge trimmer is laid on a flat surface when you fit the cutting head. Otherwise the cutting head may not be fitted straight. 1 Fit the cutting head to the shaft. CAUTION! Make sure the drive shaft inside the shaft engages with the recess in the cutting head. 2 Tighten the lower screw first, then the upper screw.
STARTING AND STOPPING Check before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. A B • Check that the machine is in perfect working order. Check that all nuts and screws are tight. • Check that the blade guard is not damaged or distorted. (HA 110) • Replace the blade guard if it is bent or damaged. (HA 110) • Make sure the gear housing is lubricated correctly.
MAINTENANCE Gear housing Maintenance schedule Below you will find some general maintenance instructions. If you need further information please contact your service workshop. There are three grease nipples on the gear housing. Use a grease gun to top up with grease. This should be carried out approximately every 20 working hours. Use Husqvarna special grease, part no. 503 98 96-01. Daily maintenance 1 2 A B CAUTION! The gear housing must not be filled completely with grease.
1140026-20 ´®z+H"^¶0G¨ ´®z+H"^¶0G¨ 2003-12-23
We hope you find the links below useful. For further gardening information visit www.GardenResources.co.