Specifications

ManualsBrandsHUSQVARNA ManualsElectronicsApplication Board Type 4

Issued by: Therese Berg

Issued date: 210421

1 (8)

Instruction for implementing Bluetooth

functionality into robotic mower systems:

Certification Requirements

In addition to technical implementation specifications, the following instructions shall be

followed when implementing boards incorporating Bluetooth functionality into Husqvarna

products.

These instructions shall be followed for all boards with the following Bluetooth design on

them:

• HQ-BLE-1: 590 54 13

The design is on all PCBs with any of the numbers:

• 582 87 12 (HMI Type 10, 11, 12, and 14)

• 590 11 35 (HMI Type 13)

• 591 10 05 (Application Board Type 1)

• 597 97 76 (Application Board Type 3)

• 598 01 59 (Base Station Board Type 1)

• 598 91 35 (Main board Type 15)

• 597 97 76 (Application Board Type 3)

• 598 90 28 (Application Board Type 4)

Changes or modifications made to this equipment not expressly approved by Husqvarna

compliance department may void the validity of the certification, for instance the FCC

authorization to operate this equipment.

The Bluetooth boards with design HQ-BLE-1 can only be used in robotic lawn mowers

and their accessories developed and manufactured by Husqvarna. The boards are only

allowed to be mounted during the manufacturing process of the robotic lawn mower

systems. The boards are not for sale for use in any other product. The boards are only

allowed to be used in the robotic lawn mower systems which are covered by the

certification.

1 Worldwide

1.1 Bluetooth Special Interest Group

For Bluetooth certification to BT SIG, the design HQ-BLE-1 is certified. All products that

uses HMI-boards or other boards with Bluetooth functionality activated shall be listed in

the BT SIG community database.

The guidelines from Bluetooth SIG regarding word mark and logos shall be followed for

documentation and information.

Summary of content (8 pages)

PAGE 1
Issued by: Therese Berg Issued date: 210421 Instruction for implementing Bluetooth® functionality into robotic mower systems: Certification Requirements In addition to technical implementation specifications, the following instructions shall be followed when implementing boards incorporating Bluetooth functionality into Husqvarna products.
PAGE 2
Issued by: Therese Berg Issued date: 210421 2 Europe 2.1 Robotic mower Make sure the robotic mower system is verified with appropriate EMC and radio standards covering at least output power, spurious emission and receiver sensitivity (i.e. blocking). 2.2 Manual and other documentation The manual of the mower system shall state the frequency and output power of the radio signals. 3 USA and Canada The boards incorporating Bluetooth have FCC and ISED approvals according to 47 CFR Part 15.
PAGE 3
Issued by: Therese Berg Issued date: 210421 3.1.1 Radiation Exposure Statement US This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
PAGE 4
Issued by: Therese Berg Issued date: 210421 3.1.3 SDoC requirements Verify that the robotic mower fulfills requirements for EMC Part 15B as required for a SDoC to be issued. It is allowed on a voluntary basis to use the FCC-logo on the device as below: 3.2 Manual 3.2.1 Warning The following information shall be in the manual for US market. It shall be placed among other warnings.
PAGE 5
Issued by: Therese Berg Issued date: 210421 (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 3.2.5 SDoC information It is recommended that the following information is included in documentation provided at the time of marketing or importation for meeting the FCC SDoC requirement.
PAGE 6
Issued by: Therese Berg Issued date: 210421 4 RoW 4.1 Japan The design HQ-BLE-1 (590 54 13) is certified according to Japanese Radio, and may not be changed in any way. 4.1.1 Robotic Mower The following text should be put on the outside of the mower device: 当該機器には電波法に基づく、技術基準適合証明等を受けた特定無線設備を装着している (Translation: “This equipment contains specified radio equipment that has been certified to the Technical Regulation Conformity Certification under the Radio Law.”) 4.1.
PAGE 7
Issued by: Therese Berg Issued date: 210421 R 202-SMG024 4.2 Brasil – Modular approval In Brasil is the Blutooth functionality planned to be certified under two licenses: • • HMI Board Type 10, 11 and 12 as a family with one certificate number, HMI Board Type 13 with one certificate number. 4.2.1 Marking on module/board The board should be marked with the certificate number. 4.2.2 Marking on product The product should be marked in a similar way as for US FCC labeling.
PAGE 8
Issued by: Therese Berg Issued date: 210421 Este produto contém a placa HMI Board Type XX código de homologação ANATEL XXXXX-XX-XXXXX. It is not allowed to add multiple board type numbers or put the info in a table etc. If the manual covers more than one model (i.e. AM105, AM310, AM315 and AM315X) where some models have Bluetooth and some don’t, we should put: Husqvarna AM310 contém a placa HMI Board Type XX código de homologação ANATEL XXXXX-XX-XXXXX.