Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Vous pouvez utiliser de l’essence contenant jusqu’à 10 % d’éthanol (E10) avec cet appareil. L’utilisation d’essence contenant plus de 10 % d’éthanol annulera la garantie du produit.
MEETS CPSC SAFETY REQUIREMENTS Husqvarna rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U.S. Consumer Product Safety Commission. CONGRATULATIONS on your purchase of a new lawn mower. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/ department.
III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the trimming area and under the watchful care of another responsible adult. • Be alert and turn machine off if children enter the area. • Before and while walking backwards, look behind and down for small children.
TABLE OF CONTENTS SAFETY RULES ........................................................ 2-3 PRODUCT SPECIFICATIONS ...................................... 3 CUSTOMER RESPONSIBILITIES................................ 3 SAFETY AND INSTRUCTIONAL DECALS ................. 4 ASSEMBLY ................................................................ 4-5 PRODUCT OVERVIEW ................................................ 6 OPERATION ............................................................ 7-12 MAINTENANCE .........
ASSEMBLY MOWING POSITION TO INSTALL ATTACHMENTS Your lawn mower was shipped ready to be used as a mulcher. To convert mower to bagging or discharging, see “TO CONVERT MOWER” in the Operation section of this manual. 1 TO REMOVE LAWN MOWER FROM CARTON 1. Remove loose parts included with mower. 2. Cut down two end corners of carton and lay end panel down flat. 3. Remove all packing materials except padding between upper and lower handle and padding holding operator presence control bar to upper handle. 4.
PRODUCT OVERVIEW 1 2 11 12 10 9 3 4 8 5 6 7 Figure 5 1. 2. 3. 4. 5. 6. Drive control levers Operator presence control bar Grass catcher Single point height adjuster Engine oil cap with dipstick Muffler 6 7. Spark plug 8. Housing 9. Air filter 10. Gas filler cap 11. Handle knob 12.
OPERATION OPERATION 2. Forward motion will stop when either the operator presence control bar or a drive control lever are released. To stop forward motion without stopping engine, release a drive control lever only. Hold operator presence control bar down against handle to continue mowing without self-propelling (Figure 7). NOTE: If after releasing the drive control the mower will not roll backwards, push the mower forward slightly to disengage drive wheels.
OPERATION TO ADJUST CUTTING HEIGHT 2 3 All four wheels are adjusted by a single lever. 1. Pull adjuster lever toward wheel. To raise mower, move lever forward to desired position. To lower mower, move the lever toward the rear (Figure 9). 4 1 1 Figure 10 1. Grass catcher frame hook 2. Rear door 3. Grass bag bracket 4. Grass catcher handle REAR DISCHARGING (See Fig. 11) 1. Lift the rear door and install the clipping deflector (available accessory) legs into holes of handle brackets as shown (Figure 11).
OPERATION SIDE DISCHARGING NOTE: Rear door must be closed. 1. Unlock latch (Figure 12). 3. Mower is now ready for side discharging operation (Figure 14). NOTE: To convert to mulching or bagging operation, discharge deflector must be removed and mulcher door must be closed and locked. 1 Figure 12 1. Latch 2. Open mulcher door and install discharge deflector under door as shown (Figure 13).
OPERATION ADD GASOLINE BEFORE STARTING ENGINE IMPORTANT: Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness (Figure 15). ADD OIL Your lawnmower is shipped without oil in the engine. For type and grade of oil to use, see “ENGINE” in the Maintenance section of this manual.
OPERATION TO START ENGINE MOWING TIPS NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal. NOTE: Your engine is equipped with an automatic choke system. No priming or choking is required before starting. 1. To start engine, hold operator presence control bar down to the handle and pull starter handle quickly. Do not allow starter rope to snap back (Figure 17).
OPERATION MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE “CLEANING”INTHEMAINTENANCESECTIONOFTHISMANUAL. • • • The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn.
MAINTENANCE BEFORE EACH USE AFTER EACH USE EVERY 10 HOURS EVERY 25 HOURS OR SEASON EVERY 100 HOURS BEFORE STORAGE Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery ** Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug Replace Air Filter Paper Cartridge Empty fuel syste
MAINTENANCE LAWN MOWER 4. Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine. 5. Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft. 6. Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise. • The recommended tightening torque is 35–40 ft. lbs. Always observe safety rules when performing any maintenance.
MAINTENANCE TO SHARPEN BLADE NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. An unbalanced blade will cause eventual damage to lawn mower or engine. • The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. • To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.
MAINTENANCE TO CHANGE ENGINE OIL AIR FILTER NOTE: Before tipping lawn mower to drain oil, empty fuel tank by running engine until fuel tank is empty. 1. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 2. Remove engine oil cap/dipstick; lay aside on a clean surface. 3. Tip lawn mower on its side as shown and drain oil into a suitable container. Rock lawn mower back and forth to remove any oil trapped inside of engine (Figure 23). 4.
MAINTENANCE MUFFLER WATER WASHOUT FEATURE Inspect and replace corroded muffler as it could create a fire hazard and/or damage. Your lawn mower is equipped with a fitting that allows quick and easy cleaning of the underside of the housing. To use this feature, proceed as follows: 1. Move lawn mower to an area of cut grass or another hard surface. NOTE: Water, grass and other debris will drain from beneath the mower housing during the washout process. 2.
SERVICE AND ADJUSTMENTS 2 CAUTION: to avoid serious injury, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Release control bar and stop engine. 2. Make sure the blade and all moving parts have completely stopped. 3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug. 2 1 13 3 5 LAWN MOWER TO ADJUST CUTTING HEIGHT See “TO ADJUST CUTTING HEIGHT” in the Operation section of this manual.
SERVICE AND ADJUSTMENTS TO ADJUST HANDLE The handle on your lawn mower has three (3) height positions - adjust to height that suits you. 1. Remove knob and carriage bolt on one side of the lower handle (Figure 28). 2. While holding handle assembly, remove knob and carriage bolt from opposite side, align hole in handle with desired hole in handle bracket and reassemble bolt and knob and tighten securely. 3. Align opposite side of handle with same positioning hole and secure with bolt and knob.
STORAGE Immediately prepare your mower for storage at the end of the season or if the unit will not be used for 30 days or more. LAWN MOWER MOWING POSITION When lawn mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area. 1. Clean entire lawn mower (See “CLEANING” in the Maintenance section of this manual). 2. Lubricate as shown in the Maintenance section of this manual. 3.
STORAGE ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.
TROUBLESHOOTING POINTS PROBLEM Does not start CAUSE CORRECTION 1. Dirty air filter. 2. Out of fuel. 3. Stale fuel. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 1. Clean/replace air filter. 2. Fill fuel tank. 3. Empty fuel tank and refill tank with fresh, clean gasoline. Water in fuel. 4. Empty fuel tank and refill tank with fresh, clean gasoline. Spark plug wire is disconnected. 5. Connect wire to plug. Bad spark plug. 6. Replace spark plug. Loose blade or broken blade adapter. 7.
Consumer Wheeled Products - Limited Warranty Husqvarna warrants to the original retail purchaser that this product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred to any subsequent purchaser of this product. Certain components (e.g.
(a) Abrasion to mower decks; (b) Tires damaged by external punctures; (c) Natural discoloration of materials due to ultraviolet light; (d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures; In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including any of the following: (e) Failure to provide or perform required maintenance services as prescribed
Consumer Wheeled Limited Warranty Chart 2012 Product/Component Riding Lawn Tractors: Frame, Chassis, Front Axle Engine* Transmission (if made by Husqvarna/Peerless) Transmission (if third party)** XLS Models only - stamped deck shell. Armor Protected Limited Warranty Fabricated Deck shell. Limited Lifetime Warranty Battery Other Non-Expendable Components Residential Zero Turn Mowers ( RZ Only ) Engine* Transmission ** RZ4623 (967009801 & 967009802) RZ5426 (967003601 & 967003602) - stamped deck shell.
Consumer Wheeled Limited Warranty Chart 2012 Consumer (personal, household use only) Product/Component Spreader Robotic Mowers Robotic Mower Battery Parts & Accessories (if purchased) Accessories (e.g., grass catcher, bumper guard accessories, etc. Parts (e.g., belts, blades, etc.
RENCONTRE LES EXIGENCES DES NORMES DE SÉCURITÉ CPSC Les tondeuses à gazon rotatives Husqvarna qui se poussent par l’arrière conforment aux normes de sécurité d’American National Standards Institute et de U.S. Consumer Product Safety Commission. FÉLICITATIONS pour votre achat d’une tondeuse à gazon . Elle a été conçue, perfectionnée, et fabriquée pour assurer le bon fonctionnement et la sûreté maximum.
• • Ne tondez pas de pentes trop rapides. Ne tondez pas l’herbe humide. Vous pourriez glisser. • III. ENFANTS • Des accidents dramatiques peuvent survenir si l’utilisateur ne fait pas attention à la présence des enfants. Les enfants sont fréquemment attirés par la machine et par la tonte de la pelouse. Ne croyez jamais que les enfants restent à l’endroit où vous les avez vu en dernier. • Tenez les enfants en dehors de l’aire de tonte sous la surveillance d’un adulte digne de confiance.
SOMMAIRE UTILISATION ................................................................... 32-37 ENTRETIEN ..................................................................... 38-42 RÉVISION ET RÉGLAGES ............................................. 43-44 ENTREPOSAGE .............................................................. 45-46 DÉPANNAGE ........................................................................ 47 GARANTIE .......................................................................
MONTAGE INSTALLER LES ACCESSOIRES POSITION DE TONTE Votre tondeuse à gazon a été expédiée prête à utiliser comme une tondeuse broyeuse. Pour la convertir au ramassage ou au déchargement, voir “POUR CONVERTIR LA TONDEUSE” dans la section d’utilisation de ce manuel. 1 POUR ENLEVER LA TONDEUSE À GAZON DU CARTON SOULEVEZ 1. Enlevez toutes les pièces détachées du carton. 2. Coupez les deux coins au bout du carton et dépliez-les. 3.
APERÇU DU PRODUIT 1 2 11 12 10 9 3 4 8 5 6 7 Figure 5 1. Leviers de la commande d’entraînement 2. Barre de commande de présence d’opérateur 3. Ramasse-herbe 4. Poignée de réglage de hauteur 5. Bouchon d’huile de moteur avec la jauge 31 6. Silencieux 7. Bougie d'allumage 8. Boîtier 9. Filtre à air 10. Bouchon de remplissage d’essence 11. Bouton de guidon 12.
UTILISATION 2. La marche avant s’arrête en lâchant la barre de commande indiquant la présence de l’opérateur ou le levier de commande. Pour arrêter la marche avant sans arrêter le moteur, lâchez uniquement les leviers de commande de l’entraînement. Maintenez vers le bas, contre la poignée, la barre de commande indiquant la présence de l’opérateur pour continuer à tondre sans déplacement automatique (Figure 7).
UTILISATION POUR RÉGLER LA HAUTEUR DE COUPE 2 3 Toutes les quatres roues sont réglées par un levier unique. 1. Tirez le levier de réglage dans la direction de la roue. Pour lever la tondeuse, bougez le levier à la position désirée. Pour baisser la tondeuse, déplacez le levier vers l’arrière (Figure 9). 4 1 1 Figure 10 1. Crochet du ramasse-herbe 2. Porte arrière 3. Support du ramasse-herbe 4. Poignée du ramasse-herbe DECHARGEMENT ARRIÈRE 1.
UTILISATION DECHARGEMENT LATÉRAL REMARQUE: Le porte arrière doit être fermée. 1. Ouvrez le verrou (Figure 12). 3. La tondeuse est maintenant prête pour le déchargement (Figure 14). REMARQUE: Pour convertir au broyage ou au ramassage, le déflecteur de décharge doit être enlevé et la porte de broyeuse doit être fermée et verrouillé. 1 Figure 12 1. Verrou 2. Ouvrez la porte de la broyeuse et installez le déflecteur comme montré (Figure 13).
UTILISATION AVANT DE DÉMARRER LE MOTEUR AJOUTEZ DE L’ESSENCE IMPORTANT: Remplissez le réservoir d’essence jusqu'au fond du goulot de remplissage. N'en mettez pas trop. Utilisez de l’essence sans plomb, régulière, fraîche, et propre avec au moins 87 indice d'octane. Ne mélangez pas l’huile avec l’essence. Pour assurer que l’essence utilisée soit fraîche, achetez des conteneurs d’essence pouvant être utilisés en moins de 30 jours (Figure 15).
UTILISATION CONSEILS DE TONTE POUR DÉMARRER LE MOTEUR REMARQUE: En raison du revêtement de protection du moteur, une petite quantité de fumée est normale la première fois qu’on utilise le produit. REMARQUE: Votre moteur est équipé d’un système de bobine automatique. Aucun amoricage ou l’obstruction n’est exigé avant de commencer. 1. Pour démarrer un moteur, tenez la barre de commande de présence d’opérateur contre le guidon et tirez rapidement sur la poignée de démarreur.
UTILISATION CONSEILS DE BROYER/TONDRE IMPORTANT: POUR LE MEILLEUR RENDEMENT, MAINTENEZ LE BOÎTIER DE TONDEUSE EXEMPT DE L’ACCUMULATION DE L’HERBE ET LES DÉBRIS. NETTOYEZ LE DESSOUS DU BOÎTIER DE TONDEUSE APRÈS CHAQUE UTILISATION. VOIR LA SECTION DE “NETTOYAGE” DANS LA SECTION D'ENTRETIEN DE CE MANUEL. • • • La lame de broyeuse spéciale recoupera beaucoup de fois l’herbe coupée pour la faire plus petite. L’herbe coupée sera distribuée partout dans la pelouse.
ENTRETIEN AVANT APRÈS TOUTES TOUTES LES TOUTES AVANT CHAQUE CHAQUE LES 10 25 HEURES LES 100 L'ENTREUTILISATION UTILISATION HEURES OU SAISON HEURES POSAGE Vérifiez l'intégrité des systèmes de fixation Nettoyez / Vérifiez le Ramasse-Herbe * Vérifier les Pneus Vérifier les Roues d'entraînement *** Nettoyez la Tondeuse **** Nettoyez sous le Couvercle d'entraînement *** Vérifiez la Courroie et les Poulies *** Vérifiez / Aiguisez / Remplacez la Lame Tableau de lubrification Nettoyez / Rechargez la Batteie ** Véri
ENTRETIEN TONDEUSE À GAZON 2. Réinstallez le déflecteur de debris avec la vis. 3. Posez la lame sur l’adaptateur de lame. IMPORTANT: POUR ASSURER L'ASSEMBLAGE ADÉQUAT, ALIGNEZ LE TROU DU CENTRE DE LAME AVEC L'ÉTOILE DU L’ADAPTATEUR DE LAME. 4. Assurez-vous que le bord arrière de la lame (opposé au bord) est vers le haut du moteur. 5. Installez le boulon de lame avec la rondelle frein et la rondelle en acier trempé dans l’adaptateur de lame et le vilebrequin. 6.
ENTRETIEN RAMASSE-HERBE AFFILER LA LAME REMARQUE: Nous ne recommandons pas que vous affilez la lame - mais si vous faites ça, la lame doit être équilibrée. Une lame mal équilibrée causera une vibration excessive et éventuellement abîmera la tondeuse ou le moteur. • La lame peut être affilée avec une lime ou une meule. N’essayez pas d’affiler la lame sans l’enlever de la tondeuse. • Pour vérifier l’équilibre de la lame, vous aurez besoin d’un boulon de dia. 5/8 po. ou d'une cheville en acier de dia. 5/8 po.
ENTRETIEN CHANGER L’HUILE DE MOTEUR FILTRE À AIR REMARQUE: Avant de basculer la tondeuse à gazon pour vidanger l’huile, vidangez le réservoir d’essence en laissant marcher le moteur jusqu’à ce que le réservoir soit vide. 1. Débranchez le fil de bougie d’allumage et posez-le de telle façon qu’il ne puisse pas entrer en contact avec la bougie d’allumage. 2. Enlevez le bouchon d’huile de moteur, posez-le à part sur une surface propre. 3.
ENTRETIEN SILENCIEUX LE DISPOSITIF DE LAVAGE DE L’EAU Votre tondeuse à gazon est équipé d’un ajustage qui permet le nettoyage rapide et facile du dessous du logement. Pour employer ce dispositif, opérez comme suit: 1. Déplacez la tondeuse à gazon à un secteur d’une herbe coupée ou d’une surface dure différente. REMARQUE: L’eau, l’herbe et d’autres débris s’écouleront sous le logement de boîter de tondeuse pendant le processus de lavage. 2.
RÉVISION ET RÉGLAGES 2 ATTENTION: AVANT D’EFFECTUER TOUS LES RÉVISION OU RÉGLAGES: 1. Relâchez la barre de commande et arrêtez le moteur. 2. Assurez-vous que la lame et toutes les pièces mobiles soient arrêtées complètement. 3. Débranchez le fil de bougie d’allumage et posez-le de telle façon qu’il ne puisse pas entrer en contact avec la bougie d’allumage. 2 1 13 3 5 TONDEUSE À GAZON POUR RÉGLER LA HAUTEUR DE COUPE 2 4 Voir “RÉGLER LA HAUTEUR DE COUPE” dans la section d’utilisation de ce manuel.
RÉVISION ET RÉGLAGES POUR RÉGLER LE GUIDON Le guidon de la tondeuse à gazon a trois (3) positions de hauteur - réglez-le à une hauteur confortable. 1. Enlevez le bouton et le boulon de chariot sur un (1) côté du guidon inférieur (Figure 28). 2. Lorsque vous tenez l’ensemble du guidon, enlevez le bouton et le boulon de chariot de l’autre côté, alignez le trou dans le guidon avec le trou désiré dans le support de guidon puis replacez le boulon et le bouton et serrez à fond. 3.
ENTREPOSAGE Préparez immédiatement votre tondeuse à gazon pour d’entreposage à la fin de la saison ou si la tondeuse à gazon ne sera pas utilisée pour une période de 30 jours ou plus. TONDEUSE À GAZON POSITION DE TONTE Quand la tondeuse à gazon doit être entreposée pour une certaine période, nettoyez-la soigneusement, enlevez toutes la saleté, la graisse, les débris feuilles. Entreposez dans un endroit propre et sec. 1.
ENTREPOSAGE MOTEUR AUTRES SYSTÈME D’ESSENCE • • IMPORTANT: IL EST IMPORTANT DE PRÉVENIR, PENDANT L’ENTREPOSAGE, LES DÉPÔTS DE GOMME DANS LES PARTIES ESSENTIELLES DU SYSTÈME D’ESSENCE TELLES QUE LE CARBURATEUR, LE FILTRE À ESSENCE, LES CONDUITES D’ESSENCE, OU LE RÉSERVOIR D’ESSENCE. LES ESSENCES CONTENANT DE L’ALCOOL (ÉTHANOL OU MÉTHANOL ET PARFOIS APPELÉES GASOHOL) PEUVENT ABSORBER DE L’HUMIDITÉ.
GUIDE DE DÉPANNAGE PROBLÈME Le moteur refuse de démarrer CAUSE SOLUTION 1. 2. 3. Filtre à air sale Sans essence. Essence trop vieille. 1. 2. 3. 4. Eau dans l’essence. 4. 5. 6. 7. 8. 9. 10. Fil de bougie d'allumage débranché. Mauvaise bougie d’allumage. Lame desserrée ou adaptateur de lame cassé. Barre de commande relâchée. Barre de commande défectueuse. La valve d’essence (si équipé) est dans la position de marche OFF. 11. Batterie faible (si équipé). 12.
Produits sur roues de consommateur – Garantie limitée Husqvarna garantit à l’acheteur original que ce produit HusqvarnaMD est exempt de vices de matériaux ou de fabrication sous des conditions normales d’utilisation et d’entretien à compter de la date d’achat au détail pour la période de garantie applicable indiquée à l’annexe A. Cette garantie ne peut être transférée à aucun aquéreur subséquent de ce produit Husqvarna®. Certains composants (p. ex.
8. Les dommages résultant du vieillissement normal, de l’usure ou de négligence ne sont PAS couverts. La garantie limitée ne couvre pas les dommages autres que ceux découlant de défauts de matériel ou de fabrication. Les points suivants ne sont PAS considérés comme des défauts de matériaux ou de fabrication et ne sont donc PAS couverts.
Tableau de garantie limitée des produits sur roues de consommateur 2012 Consommateur (perso nnel, utilisation domestique seulement) Commercial (toute utilisation commerciale, professionnelle, institutionnelle, agricole ou à revenu de production, sauf l’utilisation en location) Annexe A Location (toute utilisation en location) Aucune garantie * Aucune garantie ** Aucune garantie * Aucune garantie ** Aucune garantie Aucune garantie Aucune garantie Aucune garantie Aucune garantie Aucune garantie Aucune
Tableau de garantie limitée des produits sur roues de consommateur 2012 Produit/composant Tondeuses robotiques Tondeuse robotique Batterie Pièces et accessoires (si acheté) Consommateur (perso nnel, utilisation domestique seulement) Commercial (toute utilisation commerciale, professionnelle, institutionnelle, agricole ou à revenu de production, sauf l’utilisation en location) Annexe A Location (toute utilisation en location) 2 ans 1 an 90 jours 1 an 90 jours 1 an Aucune garantie Aucune garantie Auc
11/29/2011 BY/TH