Grass Catcher MZ54 / 966721201 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
CONGRATULATIONS on the purchase of a new collection system. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/ department. They have competent, well-trained technicians and the proper tools for service and repairs. Please read and retain this manual.
CONTENTS SAFETY.......................................................................4 ASSEMBLY.................................................................5 OPERATION................................................................9 TIPS FOR IMPROVED BAGGING......................9 GENERAL RECOMMENDATIONS.....................9 BLADE CARE......................................................9 STORAGE...........................................................9 REPAIR PARTS.................................
SAFETY SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS GENERAL OPERATION • • • • • • • • • • • • • • Read, understand and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, stones, toys, wire etc., which could be picked up and thrown by the blades. Be sure the area is clear of all people and pets before mowing.
ASSEMBLY 1 INSTALLING BAGGER MOUNT 1. Select the mount tube, lower mount hitch, spacer plate and support bracket from the kit. Using 5 /16 -18 x 1¾ round head shoulder bolts and nuts, attach the mount hitch to the mount tube as illustrated. Ensure that the elbowed arm of the tube is on the right side, with the mount hitch installed to the front. 2. Attach the support bracket to the tube assembly with two 5/16 -18 x 1¾ round head shoulder bolts and nuts. Spacer Plate T ON FR 3.
ASSEMBLY 2 3 INSTALLING CHUTE SUPPORT 1. Position upper chute support against bagger inlet, flush at outer edges. See Illustration. 2. Using support as a template, drill two 3/8 holes into bagger hood. Bagger Inlet CONTAINER MOUNTING Remove plastic end caps from the center two bag support arms. Fully insert spacer plugs into the ends of the support tubes. It may be necessary to tap the spacers into place with a hammer or mallet. Replace the plastic end cap back over the spacer.
ASSEMBLY 5 6 CONTAINER MOUNTING 1. Install containers on supports, overlapping at center supports. 2. Close cover and lock latch handles over center support tubes. LOWER CHUTE INSTALLATION 1. Raise and hold deflector shield in upright position. 2. Fit lower chute as shown and hook rear latch to mower deck. 3. Align the bracket slot on lower chute with the deflector bracket tab on the mower deck. Slide chute down over tab. 4.
ASSEMBLY 7 UPPER CHUTE INSTALLATION 8 CHUTE / HOOD INSTALLATION 1. Attach bungee latch assembly from kit. 1. Push the upper chute through the gasketed opening in the cover assembly. 2. Rotate the chute so the chute opening is downwards toward the container bags. 2. Slide upper chute onto lower chute, lining up notches and channels. 3. Stretch bungee latch up onto acorn nut on upper chute to secure.
OPERATION TIPS FOR IMPROVED BAGGING Follow the mower operation instructions in the mower operator’s manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of operation may be greater than you will experience with regular use of your grass catcher. • Always run throttle at full speed when bagging.
REPAIR PARTS 16 3 16 14 1 14 5 9 8 12 4 13 17 10 11 6 7 15 2 10 18
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 1.. 532 195373 ����1 ���� COVER 10.. 532 192603 ����1 ���� GASKET, COVER 2.. 532 400226 ����3 ���� CONTAINER, SOFT BAG 11.. 539 110281 ����1 ���� SUPPORT, CHUTE 3.. 532 130895 ����2 ���� HANDLE, BAGGER COVER 12.. 539 112294 ����1 ���� FLEX TRIM 4.. 539 108098 ����1 ���� FRAME, BAGGER 13.. 539 108096 ����2 ���� HAIR PIN 5.. 532 192709 ����1 ���� SCREEN, COVER 14..
REPAIR PARTS 18 14 2 1 4 21 21 8 11 21 21 17 25 16 5 15 3 7 20 14 26 23 10 27 19 12 22 28 28 24 13 6 26 28 9 22 12 27
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 1.. 539 131091 ���1 ��� TUBE, MOUNT 16.. 539 976937 ���2 ��� HCS 5/16-18 x 2 2.. 575 953302 ����1 ���� STRAP, LT BLK 17.. 539 990646 ����1 ���� HCS ½-13 x 1 3.. 539 132198 ����1 ���� STRAP, RT BLK 18.. 525 464701 ����3 ���� HHFS 5/16 -18 x ¾ 4.. 576 221402 ����1 ���� BRACKET, SUPPORT, BLK 19.. 539 108086 ����1 ���� NUT #10-24 ACORN 5.. 539 132192 ����1 ���� HITCH MOUNT, LOWER, BLK 20..
www.husqvarna.