Operator and Parts Manual Collection System M-ZT 52 /966793002 M-ZT 61 /966793003
CONGRATULATIONS on the purchase of a new collection system. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact the nearest authorized service center/ department. They have competent, welltrained technicians and the proper tools for service and repairs. Please read and retain this manual.
CONTENTS SAFETY RULES..........................................................4 ASSEMBLY.................................................................5 OPERATION.............................................................. 11 BLOWER ASSEMBLY.......................................12 CHUTES............................................................14 BAGGER...........................................................16 MOUNT, GUARD, BELT....................................
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS GENERAL OPERATION • • • • • • • • • • • • • • Read, understand and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, stones, toys, wire etc., which could be picked up and thrown by the blades. Be sure the area is clear of all people and pets before mowing.
ASSEMBLY 1 2 DRIVE PULLEY 1. Remove the discharge chute from the deck by removing the side hardware from the chute bracket. Retain the hardware for reuse if the collection system is removed. 2. Lower deck to the lowest cutting position. 3. Remove the right hand (discharge side) belt cover from the deck. TRIMMING BLOWER 1. Place blower assembly on secure table or stable surface. 2. Remove the bolts securing the rear mount bracket. 3.
ASSEMBLY 4 5 DRIVE BELT 1. Make sure the tension release lever is forward (disengaged). 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing. 3. Move the tension release arm to the rear and engage in the latch. Outer Pulley BELT COVERS 1. Place the deck belt shield on the deck over the drive pulley and secure with hardware removed from steel belt shield. 2. Place retainer on the outer pulley cover. 3.
ASSEMBLY 6 BAGGER MOUNT 1. Using 1¾" round head shoulder bolts and nuts, attach the mount hitch to the mount tube as illustrated. Make sure the elbowed arm of the tube is on the right side, with the mount hitch installed to the front. 2. Attach the support bracket to the tube assembly with two 1¾" round head shoulder bolts and nuts. 3. With a 1" hex bolt and nut, secure the lower mount hitch to the frame. FRONT Spacer Plate 4.
ASSEMBLY 7 8 CHUTE SUPPORT 1. Position upper chute support against bagger inlet, flush at outer edges. See Illustration. 2. Using support as a template, drill two 3/8 holes into bagger hood. COVER ASSEMBLY NOTE: For ease of assembly, you may wish assistance from another person for mounting the cover assembly to mower. 1. Position cover assembly on ground behind mower. 2. Lift and rotate cover to align the cover brackets with support assembly tubes. 3.
ASSEMBLY 10 11 1. Slide upper chute onto middle chute, lining up the middle chute latch and the acorn nut on the upper chute. 2. Stretch bungee latch up onto acorn nut to secure. Push upper chute through the gasketed opening in the cover assembly.
ASSEMBLY 12 WEIGHT ASSEMBLY 1. Remove the foot plate knob and foot plate. Set aside for later reuse. 2. Remove and reserve the three rubber grommets from the foot rest. 3. Remove the foot rest for replacement. Retain hardware for reuse. 6. Fasten the three weight plates to the weight brackets. Foot Plate Foot Rest 4. Install the three rubber grommets to the new foot rest and fasten the assembly to the frame with the hardware from the old foot rest. 5. Reinstall the foot plate and secure with the knob.
OPERATION TIPS FOR IMPROVED BAGGING • • • • • Follow the mower operation instructions in you mower operator manual. When operating the grass catcher on a lawn where grass and leaf bagging equipment has not been used, thatch and debris that has accumulated for long periods of time is picked up. The amount collected and the total time of operation may be greater than experienced with regular use of the grass catcher. Always run throttle at full speed when bagging.
REPAIR PARTS BLOWER ASSEMBLY 46 24 65 34 18 51 16 12 19 53 53 32 25 63 27 13 43 26 4 13 8 58 50 48 37 14 23 63 40 52 45 41 21 40 63 6 50 10 32 50 66 58 57 5 38 33 7 2 22 58 17 60 49 15 48 31 59 42 65 20 35 29 64 47 12 59 60 1 9 11 3 54 56 55 44 30 64 58 61 62 56 28
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. QTY. DESCRIPTION 1.. 539 130344 ���� 1 ���� HOUSING w/DECALS 33.. 539 130296 ���� 2 ���� BEARING 2.. 539 130293 ���� 1 ���� COVER, BELT 34.. 522 909602 ���� 1 ���� BRACKET, MOUNT 3.. 574 411501 ���� 1 ���� COVER, BELT 35.. 522 909502 ���� 1 ���� BRACKET, RETENTION 4.. 539 130292 ���� 1 ���� IMPELLER 36.. 525 618302 ���� 1 ���� SAND LINER, TOP 5.. 539 130295 ���� 1 ���� HUB 37.. 522 909702 ���� 1 ���� SAND LINER, BOTTOM 6..
REPAIR PARTS CHUTES 3 7 2 1 12 10 11 4 9 11 5 5 9 11 6 8 14 8
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 1.. 539 108141 ���� 1 ���� CHUTE, UPPER 7.. 539 976952 ���� 1 ���� SCREW #10-24 x 5/8 2.. 539 130294 ���� 1 ���� CHUTE, MIDDLE 8.. 539 108083 ���� 2 ���� SCREW #10-24 x 11/8 3.. 539 130933 ���� 1 ���� INDICATOR, BAG DUMP 9.. 539 108086 ���� 2 ���� NUT #10-24 ACORN 4.. 539 108088 ���� 1 ���� LATCH, HOOD 10.. 539 108089 ���� 1 ���� WELDNUT, PLATED 5.. 539 108085 ���� 2 ���� SPACER, SPLIT 11..
REPAIR PARTS BAGGER 1 16 3 8 9 14 16 5 11 15 13 17 10 7 6 4 12 2 16 15
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 1.. 532 195373 ���� 1 ���� COVER 10.. 539 110281 ���� 1 ���� SUPPORT, CHUTE 2.. 532 400226 ���� 3 ���� CONTAINER, SOFT BAG 11.. 539 112294 ���� 1 ���� FLEX TRIM 3.. 532 130895 ���� 2 ���� HANDLE, BAGGER COVER 12.. 539 108096 ���� 2 ���� HAIR PIN 4.. 532 176990 ���� 1 ���� FRAME, BAGGER 13.. 539 990627 ���� 2 ���� HCS 5/16-18 x 1¼ 5.. 532 192709 ���� 1 ���� SCREEN, COVER 14..
REPAIR PARTS MOUNT, GUARD, BELT 10 2 1 23 4 18 27 22 9 3 12 14 21 22 25 19 25 13 8 11 7 24 17 6 16 15 25 20 5 26 17 18 28
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION 1.. 539 130307 ���� 1 ���� SHIELD, BELT, 52" 539 130308 ���1 ���� SHIELD, BELT, 61" 2.. 539 130320 ���� 1 ���� PULLEY, 52" 539 130321 ���1 ���� PULLEY, 61" 3.. 539 130347 ���� 1 ���� BELT 52" ITEM PART NO. QTY. DESCRIPTION 15.. 576 221502 ���� 1 ���� SPACER 16.. 539 990645 ���� 2 ���� RHSNB 3/8-16 x 1 17.. 539 990861 ���� 4 ���� RHSNB 5/16-18 x 1¾ 18.. 539 101341 ���� 4 ���� HCS 3/8-16 x 3 19..
115 584027 Rev A 2013-02-15