Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Operator Manual M-ZT61 / 967177008 Please read the operator manual carefully and make sure you understand the instructions before using the machine.
To implement improvements, specifications and designs can be altered without prior notification. Note that no legal demands can be placed based on the information contained in these instructions. Use only original parts for repairs. The use of other parts voids the warranty. Do not modify or install non-standard equipment to the unit without consent from the manufacturer. Modifications to the unit may cause unsafe operations or damage the unit.
CONTENTS INTRODUCTION................................................................ 5 Driving and Transport on Public Roads....................... 5 Towing.......................................................................... 5 Operating..................................................................... 5 Good Service............................................................... 6 Manufacturing Number.......................................... 6 SYMBOLS AND DECALS....................................
WARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower. Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance.
INTRODUCTION Congratulations Towing Thank you for purchasing a Husqvarna ride-on mower. This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance. This manual is a valuable document. Read the contents carefully before using or servicing the machine.
INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer. See the certificate in the Service Journal in this operator manual. When you need spare parts or support in service questions, warranty issues, etc.
SYMBOLS AND DECALS These symbols are found on the machine and in the operator manual. Study them carefully so that you know what they mean. WARNING! IMPORTANT INFORMATION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.
SYMBOLS AND DECALS Read Operator Manual Whole body exposure to thrown objects Shut off engine and remove key before performing any maintenance or repair work Severing of fingers and toes Keep a safe distance from the machine Do not open or remove safety shields while engine is running Use on slopes no greater than 10° No passengers Careful backing up, watch for other people Careful going forward, watch for other people Battery acid is corrosive, explosive and flammable Moving sharp blades under c
SAFETY Safety Instructions These instructions are for your safety. Read them carefully. WARNING! THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. General Operation • Read, understand, and follow all instructions on the machine and in the manual before starting. • It is recommended that someone be aware that you are mowing and can provide help in case of injury or accident.
SAFETY • • • • • • • • • • • • 10 Operate machine only in daylight or good artificial light. Do not operate the machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways. Use extra care when loading or unloading the machine into a trailer or truck. Always wear eye protection when operating machine.
SAFETY Personal Safety Equipment WARNING! When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment. • • • • • • • Make sure that you have first aid equipment close at hand when using the machine. Never use the machine when barefoot.
SAFETY • • • Do not use on steep slopes. Do not try to stabilize the machine by putting a foot on the ground. Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in. WARNING! CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy of Pediatrics recommends that children be a minimum of 16 years of age before operating a riding lawn mower.
SAFETY Safe Handling of Gasoline WARNING! The engine and the exhaust system become very hot during operation. There is risk for burns if touched. Allow engine and exhaust system to cool before refueling. To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Use only approved gasoline container.
SAFETY General Maintenance • • • • • • • • • • • • • • • • • 14 Never operate machine in a closed area. Keep all nuts and bolts tight to be sure the equipment is in safe working condition. Never tamper with safety devices. Check their proper operation regularly. Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage and remove any fuel-soaked debris. Allow machine to cool before storing.
SAFETY Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery. WARNING! Avoid electrical sparking and its consequences by the following routines: • • • • • • • • • • • • • • • Use protective goggles.
SAFETY Transport • • • • • • • The machine is heavy and can cause serious crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer. Use an approved trailer to transport the machine. Activate the parking brake, turn off the fuel supply, and fasten the machine with approved fastening devices, such as bands, chains, or straps, when transporting. Do not operate this machine on public roadways.
SAFETY Rollover Protection System (ROPS) The ROPS increases the basic weight of the unit by 73 lbs/33 kg. • Do not use ROPS as a lifting, attaching or anchoring point. • Do not use ROPS for wrecking or towing. • Do not exceed Max GVW: 2822 lbs/1283 kg. • Read machine’s operator manual before each use. • Securely fasten the seat belt if the unit has a ROPS. • Where possible, avoid operating the unit near ditches, embankments and holes.
CONTROLS This operator manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a four-stroke overhead valve engine. Transmission from the engine is made via belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the direction and speed. Control Locations 3 4 2 1 5 11 6 10 7 8 1. Motion control levers 7. Hour meter 2. Park brake 8. Throttle control 3. Tracking knob 9. Blade switch 4. Fuel tank - left 10.
CONTROLS Motion Control Levers The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward. When both controls are in the neutral position (N), the machine stands still.
CONTROLS Parking Brake The parking brake is found on the left of the machine. Pull the lever backward to activate the brake and push forward to release it. IMPORTANT INFORMATION The machine must stand absolutely still when applying the parking brake. Always set the parking brake before dismounting. Release the parking brake before moving the mower. 8058-182 Parking brake Ignition Switch The ignition switch is placed on the control panel and is used to start and stop the engine.
CONTROLS Throttle Control The throttle control regulates the engine speed and thereby the rate of rotation of the blades, assuming the blade switch is pulled out, see Engaging the Mower Deck. In order to increase or decrease the engine speed, the control is moved forward or back respectively. Avoid idling the engine for long periods, as there is a risk of fouling the spark plugs. USE FULL THROTTLE WHEN MOWING, for best mower performance and battery charging.
CONTROLS Tracking Knob If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure for the rear tires is 15 psi (1 bar). 1. Tracking adjustments are made using the tracking bolt and tracking knob. The tracking bolt and tracking knob act as limiting devices for the motion control levers when in the full-forward position. 2. For preliminary tracking adjustment, move unit to an open, unobstructed area such as an empty parking lot or open field. 3.
CONTROLS Cutting Height Adjuster The desired cutting height is set with the height pin. The cutting height pedal releases the deck lift to place the deck at the selected height. For transport, push the lift pedal fully forward until the deck lift latches in the transport (highest) position. 2 1 1. Release pedal 2. Height pin Cut height selection pedals 8058-223 Seat Adjustment Lever The seat can be adjusted lengthways.
CONTROLS Refueling IMPORTANT INFORMATION It is recommended that fuel be added to both tanks on initial start up. Read the safety instructions before refueling. The capacity for the tank is 5 gallons (19 liters). Regularly check the gas cap gasket for damage and keep the cap properly tightened. The engine will run on a minimum of 87-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See Technical Data concerning ethanol fuel. Methanol fuel is not allowed.
OPERATION Read the Safety section and following pages, if you are unfamiliar with the machine. Training Due to unique steering capabilities, zero turn mowers are far more maneuverable than typical riding mowers. This section should be reviewed in its entirety prior to attempting to move the mower under its own power. When first operating the mower or until becoming comfortable with controls, use a reduced throttle speed and reduced ground speed.
OPERATION Roll Bar and Safety Belt Operate the unit with the roll bar in the raised and locked position and use the seat belt. There is no rollover protection when the roll bar is down. If it is necessary to lower roll bar, do not wear the seat belt. Raise the roll bar as soon as clearance permits. WARNING! The seat belt must be used when the roll bar is in upright position. Before Starting 1. Read the sections Safety and Controls before starting the machine. 2.
OPERATION Starting the Engine 1. Sit on the seat. 2. Raise the mower deck to the transport position by setting the lift pedal fully forward. 3. Activate the parking brake. 8058-225 Set mower deck to the transport position 4. Disengage the mower blades by pressing the blade switch down. 8058-043 Press the control for disengaging the mower deck 5. Move the steering controls outward to the locked (outer) neutral position.
OPERATION 6. Move the throttle to the middle position. WARNING! Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects or other reproductive system damage. The engine exhaust contains carbon monoxide, which is an odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces. 8058-050 Set the throttle 7. Open the fuel tank valve. 8. Press in and turn the ignition key to the start position.
OPERATION Weak Battery If the battery is too weak to start the engine, it should be recharged. (See Battery in the Maintenance section.) WARNING! Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. IMPORTANT INFORMATION The mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use the mower to start other vehicles.
OPERATION Running 1. Release the parking brake by moving the lever downward. NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. 8058-182 Release the parking brake 2. Move the steering controls to the neutral position (N). WARNING! Make sure that no one is near mower when engaging blade switch.
OPERATION Operating on Hills Read the Safety Instructions Driving on Slopes in the Safety Instructions. WARNING! Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across slopes. • • • The slowest speed possible should be used before starting up or down hills. Avoid stopping or changing speed on hills. If stopping is absolutely necessary, pull drive levers into the neutral position and push to the outside of the unit and engage the parking brake.
OPERATION Stopping the Engine For all models, move the throttle to the minimum position (tortoise symbol). If the engine has been worked hard, allow it to idle a minute to attain a normal operating temperature before stopping. To prevent fouling the spark plugs, avoid idling the engine for longer periods. 1. Disengage the mower deck by depressing the blade switch. 8058-046 Disengage the mower deck and move throttle to minimum 2.
OPERATION Mowing Tips • • • • • • • • • Observe and flag rocks and other fixed objects to avoid collisions. Begin with a high cutting height and reduce it until the desired mowing result is attained. The average lawn should be cut to 2½" (64 mm) during the cool season and over 3" (76 mm) during the hot months. For healthier and better looking lawns, mow often after moderate growth. For best cutting performance, grass over 6" (15 cm) in height should be mowed twice.
OPERATION Moving Machine By Hand WARNING! 2 No adjustments or maintenance should be carried out unless: • the engine stopped • the ignition key removed • the parking brake activated When pushing or pulling the mower, engage the bypass linkages with the hydro release levers. The levers are located on each side of the rear of the unit below the engine plate. Raise the deck to the highest (transport) position. Pull the bypass linkages up and out of the keyhole slots.
MAINTENANCE Daily MAINTENANCE Check the parking brake Check the engine’s oil level (every refueling) Check the safety system Check for fuel and oil leakages Check/clean the engine’s cooling air intake Check the mower deck Check for loose hardware (screws, nuts) Clean under the mower deck Start the engine and blades, listen for unusual sounds Check for damage Thoroughly clean around the engine Clean around belts, belt pulleys Check the tire pressures Check battery connections Sharpen3)/ Replace mower blades
MAINTENANCE Daily MAINTENANCE Before After At least once each year Maintenance interval in hours 50 Check/adjust throttle cable ● ■ ■ ■ ● ■ ● ■ ● ● Check the condition of belts, belt pulleys Change the engine oil 1) Replace the engine oil filter Clean/replace the spark plugs Replace the fuel filter Replace paper air filter 2) Check the caster wheels (every 200 hours) Replace the air cleaner’s foam pre-filter 2) Change the hydraulic oil (every 500 hours) Replace the hydraulic oil filter (every 500 h
MAINTENANCE Battery STANDARD The mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • See chart for charging times. BATTERY STATE APPROXIMATE BATTERY CHARGING TIME* TO FULL CHARGE AT 80OF / 27OC OF CHARGE Maximum Rate at: 50 Amps 30 Amps 12.6V 100% 12.4V 75% 20 min. 12.2V 50% 45 min. 12.
MAINTENANCE Safety System This machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: • The mower deck is disengaged. • The steering controls are in the outer, locked neutral position. • The parking brake is on. Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again.
MAINTENANCE Deck Belt Deck Belt Removal Park on a level surface. Apply park brake. Lower the deck into the lowest cutting position. 1. Remove foot plate and belt shields. 2. Using a ratchet or breaker bar with a 9/16" socket on the spring idler bolt, relieve the tension on the belt. 3. Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface. 4. Carefully roll the belt over the top of the cutter housing pulleys. 5.
MAINTENANCE Pump Belt The belts are not adjustable. Replace belts if they begin to slip from wear. Replacing Pump Belt Park the mower on a level surface. Engage the parking brake. Belt Removal From the top side of the deck: 1. Remove the deck belt (see Deck Belt Removal in this section of the manual). 2. Tilt seat forward to access fan covers. Remove both fan covers. From the underside of the mower: 3. Remove clutch stop to access the belt. 4.
MAINTENANCE Cutting Blades To attain the best mowing effect, it is important that blades are well sharpened and not damaged. Replace blades that have been bent or cracked when hitting obstacles. Let the service workshop decide whether a blade with large nicks can be repaired/ground or must be replaced. Balance the blades after sharpening. Check the blade mounts. Blade Replacement WARNING! Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling. 1.
MAINTENANCE Adjusting the Mower Deck WARNING! Check the tire pressure before adjustment of the mower deck. See Tire Pressures in Maintenance section. Faulty mower deck adjustments will cause an uneven mowing result. Leveling deck Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to the correct pressure. See Technical Data / Transmission. If tires are under or over inflated, you cannot properly adjust your deck. Four slots control the height and pitch of the mower deck.
MAINTENANCE Anti-scalp Rollers Anti-scalp rollers keep the deck in the proper position to help prevent scalping in most terrain conditions. Do not adjust the rollers to support the deck. Rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position. IMPORTANT INFORMATION Adjust anti-scalp rollers with the mower on a flat level surface.
MAINTENANCE ZT-3400 Powertrain Cleaning Regular cleaning and washing, especially under the mower deck, will increase the machine’s life-span. Make it a habit to clean the machine directly after use (after it is cooled), before the dirt sticks. Do not spray water on the top of the mower deck. Use compressed air to clean the top side of mower deck. Regularly clean deck and underside of the deck with normal water pressure. Do not use a high pressure washer or steam cleaner.
LUBRICATION Lubrication Schedule 8065-095 12/12 Every year Lubricate with grease gun Filter change Oil change Level check 1/52 Every Week 1/365 Every day * Change hydraulic drive filters. p Change engine oil every 50 hours. General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil. When lubricating with grease, unless otherwise stated, use high grade molybdenum disulphide grease.
LUBRICATION Wheel and Deck Zerks Use only good quality bearing grease. Grease from well-known brand names (petrochemical companies, etc.) usually maintains a good quality. Front Wheel Mount Lubricate with a grease gun until the grease is forced out. Front Wheel Bearings Lubricate 3-4 strokes with a grease gun on each set of wheel bearings. 8058-068 Lubricating front wheels Deck Spindle Lower the cutting deck completely.
LUBRICATION Transaxle (Transmission) Fluid Change This transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality levels and longer life, an oil filter change interval of every 200 hours is recommended. The following procedure is performed with the transaxles installed in the mower and the mower on level ground. Apply the pump release valve for each transaxle and set the parking brake. 1. Remove the three ¼" filter guard screws and filter guard.
LUBRICATION Transmission Purging Due to the effects air has on efficiency in hydrostatic drive applications, it is critical to purge the system. These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional oil has been added to the system. Resulting symptoms in hydrostatic systems may be: • Noisy operation. • Lack of power or drive after short term operation. • High operation temperature and excessive expansion of oil.
TROUBLESHOOTING GUIDE Problem Engine will not start Starter does not turn the engine over Engine runs rough Engine seems weak Cause • Blade switch is engaged • Steering controls are not locked in the neutral position • Parking brake is not activated • Battery is dead • Contamination in the carburetor or fuel line • Fuel supply is closed or the tap for the fuel tank is in the wrong position • Clogged fuel filter or fuel line • Faulty ignition system • Dead battery • Poor cont
TROUBLESHOOTING GUIDE Problem Machine vibrates Engine overheats Battery not charging Machine moves slowly, unevenly, or not at all Mower deck not engaging Hydraulic drive leaks oil Uneven mowing results 50 Cause • Blades are loose • Blades are incorrectly balanced • Engine is loose • Clogged air intake or cooling fins • Engine overloaded • Poor ventilation around engine • Defective engine speed regulator • Too little or no oil in the engine • Fouled spark plug • Poor con
STORAGE Winter Storage The machine should be readied for storage at the end of the mowing season, or if it will not be in use for more than 30 days. Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function. Fuel stabilizers are an acceptable option as regards to the sticky residues that can occur during storage. Add stabilizer to the fuel in the tank or in the storage container.
WIRING DIAGRAM TIMER SCHEMATIC 52
TECHNICAL DATA Torque Specifications Hex Head Cap Screws The torque values shown should be used as a general guideline when specific torque values are not given. U.S. Standard Hardware Shank Size (Diameter in inches, fine or coarse thread) Grade SAE Grade 5 SAE Grade 8 Size ft./lbs Nm ft./lbs Nm ¼ 9 12 13 18 /16 18 24 28 /8 31 42 /16 50 ½ Flangelock Screw w/Flangelock Nut ft.
TECHNICAL DATA 1) Engine Manufacturer Kawasaki Type FS691V Power 23 HP 1) Lubrication Fuel Fuel tanks capacity Cooling Alternator Starter Pressure w/ Oil Filter Min 87 octane unleaded (Max ethyl alcohol 10%, Max MTBE 15%) 5 gallons / 18.8 liters Air cooled 12v 15 amp @ 3600 rpm Electric Transmission Transmission Speed and direction controls ZT-3400 Hyrdo Gear Dual levers, foam gripped Speed forward 0-10 mph - 0-16.
CONFORMITY CERTIFICATES USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove any of these labels. Certificates can also be supplied with the machine at delivery or written in the Engine manual. Take care of them as they are valuable documents.
SERVICE JOURNAL Action Date, mtr reading, stamp, sign Delivery Service Charge and connect the battery Adjust the tire pressure of all wheels to 15 PSI (1 bar) Connect the contact box to the cable for the seat’s safety switch Check hydraulic oil level Check hydraulic hoses for kinking or leaks Check neutral position Fill with fuel and open the fuel shut off valve Start the engine Check that there is drive to both wheels Check mower deck pitch and adjustment ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ Check: Safety switch for th
SERVICE JOURNAL Action Date, mtr reading, stamp, sign After 10 hours Change the engine oil ¨ Change the oil filter ¨ Inspect hydraulic hoses ¨ Inspect hydraulic belt ¨ Inspect hydraulic filter ¨ Check neutral position ¨ Check safety system ¨ Check seat belt ¨ Check ROPS ¨ Check fuel system for leaks ¨ Inspect safety guards and shields ¨ Check brake adjustment ¨ 57
SERVICE JOURNAL Action Date, mtr reading, stamp, sign Daily Service Clean debris from mower ¨ Check engine oil level ¨ Check the tire pressures ¨ Check underside of deck ¨ Inspect deck pulleys ¨ Check/clean the engine’s cooling air intake ¨ Check safety system ¨ Check seat belt ¨ Check ROPS ¨ Check fuel system for leaks ¨ Inspect safety guards and shields ¨ Check brake adjustment ¨ 58
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 50-Hour Service Clean debris from mower ¨ Check engine oil level ¨ Check the tire pressures ¨ Check underside of deck ¨ Inspect deck pulleys ¨ Check/clean the engine’s cooling air intake ¨ Check safety system ¨ Check seat belt ¨ Check ROPS ¨ Check fuel system for leaks ¨ Inspect safety guards and shields ¨ Check brake adjustment ¨ 59
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 250-Hour Service Grease fittings (caster pivots and caster wheels) ¨ Inspect dampers ¨ Inspect frame ¨ Inspect throttle cable ¨ Inspect hardware ¨ Check the tire pressures ¨ Change the engine oil and filter ¨ Change air filter ¨ Inspect spark plug ¨ Inspect fuel filter ¨ Check engine RPM ¨ Clean underside of deck ¨ Check blade pitch ¨ Grease blade spindles ¨ Inspect spindle bearings ¨ Inspect deck belt and blades ¨ Inspe
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 500-Hour Service Grease fittings (caster pivots and caster wheels) ¨ Inspect dampers ¨ Inspect frame ¨ Inspect throttle cable ¨ Inspect hardware ¨ Check the tire pressures ¨ Change the engine oil and filter ¨ Change air filter ¨ Inspect spark plug ¨ Inspect fuel filter ¨ Check engine RPM ¨ Clean underside of deck ¨ Check blade pitch ¨ Grease blade spindles ¨ Inspect spindle bearings ¨ Inspect deck belt and blades ¨ Inspe
SERVICE JOURNAL Action Date, mtr reading, stamp, sign At Least Once Each Year Clean the engine’s cooling air intake ¨ Replace the air cleaner’s foam pre-filter ¨ Replace the air filter’s paper cartridge ¨ Change the engine oil ¨ Replace the engine oil filter ¨ Check/adjust the cutting height ¨ Check/adjust the parking brake ¨ Clean/Change the spark plugs ¨ Inspect spark plug ¨ Check the engine valve clearance ¨ 62
www.husqvarna.
