Operator’s manual FS 1000 E Please read the Operator’s manual carefully and make sure you understand the instructions before using the machine.
Compliance with EU directives Husqvarna Construction Products Sweden AB, Box 2098, SE-550 02 Jönköping, Sweden, tel: +46 (0)36-570 60 00, hereby certifies that its FS-1000 floor saw, having serial numbers 01001 onwards, is manufactured in compliance with the Council's machines directive 98/37/EG, low-voltage directive 73/23/EEG and EMC directive 89/336/EEG, including amendments, and that the following standards were used for guidance: EN 55 014-1, EN 55 014-2, EN 61 000-3-2, EN 50 144-1.
Contents General instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Description and purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Rating plate, warning signs and their meanings . . . . . . . . . . .5 Preparations before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Starting and operating . . . . . . . . . . . . . . . . . . . . . . . . . .
General instructions ____________________________________________________________________________________________ Figure 1.1 The FS 1000 EM floor saw is a professional machine designed for cutting reinforced concrete, asphalt and stone. 7 This machine may only be used by those who have carefully read this instruction manual and follow its instructions. 1 4 5 6 3 If you are unsure about any point please consult the supplier before starting to use the machine.
___________________________________________________________________________________________________________________________________________________________________________________ 2. Safety precautions 2.1. Warning signs and their locations You must follow the safety precautions before starting the machine. If the user does not follow these precautions then neither Husqvarna Construction Products Sweden AB nor its representative can accept any liability, whether direct or indirect.
___________________________________________________________________________________________________________________________________________________________________________________ • Set up a barrier or signs around the working area to prevent any unauthorised personnel from being injured or disturbing the operator while working. • Check the belt tension as described in section 5.3. Adjust if necessary using the belt tensioning screw. Turning clockwise tightens the belts.
___________________________________________________________________________________________________________________________________________________________________________________ • Lower the base plate by raising the safety catch. • Turn on the cooling water to provide adequate cooling and prevent dust formation. • Release the parking brake, while holding the guide handle on the machine with your other hand. (CAUTION! Do not hold the feed knob if you do not have full control over the machine.
___________________________________________________________________________________________________________________________________________________________________________________ Figure 5.2 2 3 • Fit the blade. NOTE! Direction of rotation. See arrow on body of blade. • Use the smaller of the two spanners supplied to prevent the blade shaft from turning, and use the larger spanner to undo or tighten the blade flange nut. See figure 6,1. • Lower the blade guard. 1 Figure 6.1 7 6 5.2.1.
___________________________________________________________________________________________________________________________________________________________________________________ 7. Lifting and transporting the floor saw Figure 7.2 The FS 1000 EM floor saw has a lifting eye, which must be used when lifting the machine. Don't lift using any other parts, as this could cause damage to the machine and personal injury.
___________________________________________________________________________________________________________________________________________________________________________________ Technical specifications The table below gives the technical specifications for the floor saw. It is extremely important that you check these before: - Choosing a floor saw. - Choosing and fitting a diamond blade. - Connecting to the mains supply. - Choosing a power cable. - Choosing the cutting depth. - Transporting the machine.
Description Pos. no. Part No. 1 Frame 44 531072162 4 Screw M12x45 M6S 8.8 FZB 2 Wheel axle 45 531072165 1 Screw M16x110 M6S 8.8 FZB 531072193 4 Wheel FS800E & FS1000E 46 531072147 1 Nut M16 M6M GR8 FZB Pos. no. Part No.
Part No. Quantity 87 Pos. no. 531072186 1 Emergency stop FS1000E Description Parts no longer stocked up to serial no. 9405 88 531072179 1 Terminal box FS1000E 531072093 1 Pulley shaft earlier version 89 501354001 1 Base plate mounting 531072094 1 Pulley shaft assembly earlier version 90 501354101 1 Base plate 52G37207 4 Older version of wheel 91 531072121 1 Base plate shaft 531072092 2 Older version of wheel axle 92 531072156 3 Screw M10x30 M6S 8.
www.husqvarnacp.
