Operator’s Manual Read these instructions carefully and make sure you understand them before using the PP 418. PP 418 Manual del operador Lea cuidadosamente estas instrucciones y asegúrese de que las comprende bien antes de usar el PP 418. Manuel d’utilisation Veuillez lire attentivement ces instructions et assurez-vous de bien les comprendre avant d’utiliser la machine modèle PP 418.
INTRODUCTION Careless or improper use of this Power Pack can cause serious or even fatal injury. Carefully read and understand and follow ALL instructions in this manual as well as the instructions in the included BRIGGS & STRATTON Operator’s Manual before using the PP 418 Hydraulic Power Pack. Allow only competent adults to operate this power pack. It is the owner’s responsibility to ensure that all operators of this power pack have read and understand the content of this manual.
REGISTER THE PRODUCT Please register your new Power Pack with Husqvarna Construction Products by mailing in the registration card that came with the machine or you can register on the internet site www.husqvarnawarranty.com Registration will allow us to contact in case of any critical updates or recalls on this machine. Warranty registration has also been found to be helpful in tracing stolen equipment.
LIFTING AND LOADING CONTENTS Content Lifting and Loading the PP 418 Page Introduction, personal safety ...................... 2 Registration of the product ………………… 3 General safety message............................. 3 The Power Pack 418 weighs approx 135kg/298lb. Table of contents ………………………….. What is what? ............................................ 4 5 Decals ........................................................
WHAT IS WHAT C B A D N E F M L K H J O G T P Q S Engine model, type and code. R Power Pack model number and serial number What is what? A. B. C. D. E F. G. H. J. K. L. M. N. O. P. Q. R. S. T. U. V. W. W More information on page Lifting eyelet................................................ Rack for hydraulic hoses Fuel gauge/fuel cap.................................... Choke lever Lock for handle Transport handle Battery.........................................................
DECALS AND LOCATIONS Part number: 541 20 76-21 Part number: 542 16 90-65 Part number: 510 04 40-01 Part number: 541 20 76-22 HYDRAULIC OIL ISO-46 Part number: 501 98 70-01 Part number: 510 19 10-01 Part number: 510 19 09-01 Part number: 510 19 08-01 Part number: 510 19 09-02 6
WHAT TOOLS CAN BE POWERED The PP 418 power pack is equipped with an adjustable flow hydraulic pump which produces hydraulic power more efficiently than a more commonly used fixed displacement gear pump.
FUEL HANDLING OIL HANDLING WARNING NOTICE Used oil is a hazardous waste product. Dispose of used oil properly. Do not discard with household waste. Check with your local authorities, service center, or dealer for safe disposal/recycling facility. Taking the following precautions will lessen the risk of injury and property damage: - Use extreme care in handling gasoline. It is extremely flammable and the vapors are explosive. - Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
ASSEMBLY Step 3 Hook up the hydraulic hoses to the power pack. Connect the two couplers in the free end of the hose. The hoses are now ready to be charged with oil from the oil tank. NOTICE The PP 418 power pack must be serviced before use. In some markets the power pack will be delivered filled with both engine oil and hydraulic oil. NOTE: The hoses can be installed with either end to the power pack.
SERVICING THE BATTERY Use the following procedure when removing, installing and attaching the battery cables. The battery is located in the support foot of the power pack. To access the battery you will need another person helping you. Step 1 Remove the two M8 bolts using a 10 mm wrench. Keep the two bolts nearby for Step 3 The battery supplied as original equipment is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking the electrolyte level is not necessary.
CONTROLS - OPERATION Choke Lever Throttle Control Ignition Switch Flow Selector IGNITION SWITCH STOP – Kills the engine – no power to any of the electrical devices. RUN – Run position for the engine. Please note that the hour meter will collect time whether or not the engine is running. If the key is left in the RUN position the battery will also loose power more quickly. START – Turns the engine starter motor. cont..
STARTING CHECKLIST BEFORE YOU OPERATE THE POWER PACK, PLEASE REVIEW THE FOLLOWING CHECKLIST: STARTING PROCEDURE: WARNING - Have you read and do you understand ALL instructions and warnings in this manual? ASPHYXIATION HAZARD Running an engine in a confined or badly ventilated area can result in injury or death due to asphyxiation or carbon monoxide poisoning.
ADJUSTING THE AUTOMATIC THROTTLE GENERAL DESCRIPTION The AUTOMATIC THROTTLE function is triggered by an adjustable pressure switch located on the hydraulic manifold. ADJUSTMENT On the PP 418 the threshold pressure at which the throttle reacts can be adjusted to reach a desired function for a specific tool and condition. Step 1 Hook up the hoses and tool to be used. Throttle Control Pressure Switch Step 2 Turn the AUTOMATIC THROTTLE switch to the ON position. Start the engine and let it idle for 1 minute.
ENGINE MAINTENANCE Engine Oil NOTICE Checking, Adding and Changing Oil Used oil is a hazardous waste product. Dispose of used oil properly. Do not discard with household waste. Check with your local authorities, service center, or dealer for safe disposal/recycling facility. Always check the oil level before starting the engine. Keep oil level at FULL. Do not overfill. Check level daily, or after every eight (8) hours of use. Note: Engine holds approximately 1.4 liters (1.
HYDRAULIC MAINTENANCE HYDRAULIC SYSTEM SPECIFICATIONS Oil Tank volume: 10 liter (2.6 gal) Oil Type: ISO 46 (see page 8) Hydraulic Filter (large): 510 02 33-01 25 Micron filter ALWAYS REPLACE both filters and oil every 100 hours Hydraulic Filter (small): 542 16 64-49 25 Micron filter NOTICE: Never use automotive type oil filters. They do not have the required flow capacity and can burst during operation.
TECHNICAL SPECIFICATIONS Weight and Dimensions PP 418 Weight – dry without hoses Weight with oil but without gasoline 127 kg 135 kg 280 lbs 298 lbs Weight - hose set ½” x 7.5 m (25 feet) – dry Weight - hose set – with oil 8.
WARRANTY HUSQVARNA EQUIPMENT WARRANTY New Hydraulic Power Packs sold by Husqvarna Construction Products are warranted to be free from manufacturing defects in normal service for a period of one (1) year from date of purchase by the original consumer purchaser. Please see the enclosed warranty registration card for the complete warranty statement. The BRIGGS & STRATTON engine warranty is two (2) years from the date of purchase by the original consumer purchaser.
CONFORMITY CERTIFICATES CALIFORNIA AIR RESOURCES BOARD (CARB): This machine is considered a preempt Off-Road Application as relating to CARB standards. Under construction equipment, and in particular, as a Hydraulic Power Pack (Power pack: hydraulic), with engine power less than 19KW (25hp), CARB standards do not apply to this machine. For more information see the website http://www.arb.ca.gov/msprog/offroad/preempt.
510 02 98-01 2008-31 Printed In U.S.A.