Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto. the product warranty.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN • • WARNING. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy of Pediatrics recommends that children be a minimum of 12 year of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of age before operating a riding lawn mower. If fuel is spilled on clothing, change clothing immediately. Never overfill fuel tank. Replace gas cap and tighten securely.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 1.5 Gallons/5,67 L Regular Unleaded Oil Type: (API: SG-SL) SAE 30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: W/Filter: 56 Oz./1,65 L W/out Filter: 48 Oz./1,4 L Spark Plug: Champion RC12YC (Gap: .030"/0.76 mm) 3 Amps Battery 5 Amps Headlights Charging System: Battery: Blade Bolt Torque: Amp/Hr: Min. CCA: Case size: CONGRATULATIONS on your purchase of a new tractor.
UNASSEMBLED PARTS Bagger Steering Wheel 1/4 x 20 Flange Lock Nuts Bagger Spring Latch Steering Wheel Insert 1/4 x 20 x 3/4 Shoulder Bolts Clevis Pin 1/4 x 20 x 1.15 Shoulder Bolts Retainer Spring Clip 1/4 x 20 x 1.
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness. TOOLS REQUIRED FOR ASSEMBLY INSTALL STEERING WHEEL • Position front wheels of the tractor so they are pointing straight forward.
ASSEMBLY TO INSTALL HOOD SCOOP (See Fig. 5) SEAT SWITCH PAD SLOT SEAT PAN TAPE WIRING HARNESS Fig. 3 TO ADJUST SEAT • Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle. TAPE SLOT PAD FLAT WASHER SEAT PAN BOLT ADJUSTMENT HANDLE TAB Fig. 4 NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid.
ASSEMBLY TO ASSEMBLY BAGGER (See Figs 6 - 8) • • • • • • Unfold bag and stand right side up. Feed front bagger frame (1) up through fabric loops at each side of bagger. Snap bottom of front bagger frame (1) into snap feature at front of bagger bottom. Slide bagger fabric loop (2) segments at the ends of bag onto top bagger frame tubing. Uninstall two (1\4”-20 x 1.15”) hex bolts (3) from the front of top frame. Reinstall the two (1\4”-20 x 1.
ASSEMBLY TO INSTALL BAGGER SPRING LATCH (See Fig. 11 & 12) • • The bagger spring latches are located on the back plate (1), one in each of the bottom corners. • Before installing, tractor engine must be shut off and parking brake engaged. • Install each bagger spring latch with the loop end (2) down and facing towards the bagger assembly. • Place the mounting bolt (3) through the curved end of the bagger spring latch, through the back plate, and secure with nut (4) as shown. Tighten firmly.
ASSEMBLY ✓CHECKLIST BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ All assembly instructions have been completed. No remaining loose parts in carton. Battery is properly prepared and charged. Seat is adjusted comfortably and tightened securely. All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. H E D B G F A C J Fig. 14 Our tractors conform to the applicable safety standards of the American National Standards Institute. (A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your tractor.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR • TO SET PARKING BRAKE (See Fig. 15) Your tractor is equipped with an operator presence sensing switch.
OPERATION • Start tractor with clutch/brake pedal depressed and gearshift lever in neutral position. • Move gearshift lever to desired position. • Slowly release clutch/brake pedal to start movement. IMPORTANT: Bring tractor to a complete stop before shifting or changing gears. Failure to do so will shorten the useful life of your transaxle. • • With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground.
OPERATION REVERSE OPERATION SYSTEM (ROS) (See Fig. 22) • • Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position. • • WARNING: Backing up with the attachment clutch engaged while mowing is strongly discouraged.
OPERATION MOWING TIPS IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F (0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP ENSURE GOOD COLD WEATHER STARTING. • CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with o
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.
MAINTENANCE V-BELTS TO CHANGE ENGINE OIL (See Fig. 27) Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. • Remove oil fill cap/dipstick.
MAINTENANCE CLEANING CLEAN AIR SCREEN • Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. • AIR FILTER Clean engine, battery, seat, finish, etc. of all foreign matter. Clean debris from steering plate. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of drive. CAUTION: Avoid all pinch points and movable parts (See Fig.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift lever in neutral position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS • • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. Repeat on opposite side of tractor. • • Insert end of link (E) into hole in front mower bracket and secure with washer and retainer spring (J). Hook end of clutch cable spring (Q) into hole in idler arm (R). E A J F B H Fig. 32 • Fig.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see step in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 39 & 40) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 3/8" lower than the rear tip when the mower is in its highest position.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 41) BELT REMOVAL • Remove mower (See “TO REMOVE MOWER” in this section of manual). NOTE: Observe entire motion drive belt and position of all belt guides and keepers. • Remove belt from stationary idler (A) and clutching idler (B). • Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (D). • Remove belt downward from engine pulley (E).
SERVICE AND ADJUSTMENTS TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 43) TO ADJUST STEERING WHEEL ALIGNMENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly section of this manual. The transaxle should be in neutral when the gear shift lever is in neutral (lock gate) position.
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Figs. 46) TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 47) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. • • • • • • • • • Raise hood. Unsnap headlight wire connector. Stand in front of tractor.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when oper-ator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. Worn, bent or loose blade. 2. Mower deck not level. 3. Buildup of grass, leaves, and trash under mower. 4. Bent blade mandrel. 5.
Consumer Wheeled Products - Limited Warranty Husqvarna warrants to the original retail purchaser that this product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred to any subsequent purchaser of this product. Certain components (e.g.
(a) Abrasion to mower decks; (b) Tires damaged by external punctures; (c) Natural discoloration of materials due to ultraviolet light; (d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures; In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including any of the following: (e) Failure to provide or perform required maintenance services as prescribed
Consumer Wheeled Limited Warranty Chart 2012 Product/Component Riding Lawn Tractors: Frame, Chassis, Front Axle Engine* Transmission (if made by Husqvarna/Peerless) Transmission (if third party)** XLS Models only - stamped deck shell. Armor Protected Limited Warranty Fabricated Deck shell. Limited Lifetime Warranty Battery Other Non-Expendable Components Residential Zero Turn Mowers ( RZ Only ) Engine* Transmission ** RZ4623 (967009801 & 967009802) RZ5426 (967003601 & 967003602) - stamped deck shell.
Consumer Wheeled Limited Warranty Chart 2012 Consumer (personal, household use only) Product/Component Spreader Robotic Mowers Robotic Mower Battery Parts & Accessories (if purchased) Accessories (e.g., grass catcher, bumper guard accessories, etc. Parts (e.g., belts, blades, etc.
1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles III. NIÑOS • • ADVERTENCIA: LOS NIÑOS PUEDEN SUFRIR DAÑOS CON EL USO DE ESTE EQUIPO. La Academia Estadounidense de Pediatría (American Academy of Pediatrics) recomienda que sólo se permita a niños con una edad mínima de 12 años manejar máquinas cortacésped manuales, y al menos de 16 años para manejar tractores cortacésped.
ESPECIFICACIONES DEL PRODUCTO Capacidad Y Tipo De Gasolina: 1.5 Galones (5.67 L) Regular Sin Plomo Tipo De Aceite: (Api: Sg-Sl) SAE 30 (Sobre 32°F/0°C) SAE 5W30 (Debajo 32°F/0°C) Capacidad De Petróleo: Con Filtro: Sin Filtro: Bujía: Champion RC12YC Abertura: .030" (0,76 Mm) Sistema De Carga: 3 Amps Batería 5 Amps Faros Batería: Amp/Hr: Min. Cca: Case Size: Torsión Del Perno De La Cuchilla: FELICITACIONES por la compra de su tractor.
PEDAZOS PARA LA MONTAJE Volante de dirección Contenedor Resorte para trabar 1/4 x 20 Tuerca de reborde Inserto del volante de dirección Volante de dirección 1/4 x 20 x 3/4 Perno hexagonal 1/4 x 20 x 1.15 Perno hexagonal Adaptador Accesorio de transción de la dirección Pasador (1) Perno 1/4 x 20 x 1.
MONTAJE/PRE OPERACIÓN Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío. Para asegurarse que su tractor funcione en forma adecuada y segura todas las partes y los artículos de ferretería que se monten tienen que ser apretados en forma segura. Use las herramientas correctas, según sea necesario, para asegurarse de que estén apretados en forma segura.
MONTAJE/PRE OPERACIÓN AVISO: Ahora puede rodar su tractor fuera de la corredera. Siga las siguientes instrucciones para remover el tractor de la corredera. INSTALACIÓN DEL ASIENTO (Vea Figs. 3 y 4) • • • • Remueva la perno y la arandela plana que aseguran el asiento al empaque de cartón y póngalos de lado para poder utilizarlos durante la instalación del asiento sobre el tractor. Remueva y desechese del embalaje de cartón. Conecte el interruptor con el asiento.
MONTAJE/PRE OPERACIÓN PARA MONTAR EL CONTENEDOR (Vea Fig. 6 - 8) • • • • • • Desdoble la bolsa y ponga el lado derecho hacia arriba. Introduzca el bastidor frontal (1) hacia arriba por las argollas del tejido de cada lado de la ensacadora. Encaje la parte inferior del bastidor frontal (1) en el resorte de la parte anterior del fondo de la ensacadora. Deslice la parte de las argollas del tejido (2), situadas en los extremos de la bolsa, sobre los tubos del bastidor superior de la ensacadora.
MONTAJE/PRE OPERACIÓN CÓMO INSTALAR EL CIERRE DE MUELLE DE LA BOLSA COLECTORA (Vea Fig. 11 y 12) • • Los cierres de muelle de la bolsa colectora se encuentran en la placa posterior (1), uno en cada esquina inferior. • Antes de la instalación, es necesario detener el motor del tractor y accionar el freno de estacionamiento. • Instale cada cierre de muelle de la bolsa con el extremo en forma de lazo (2) hacia abajo y enfrentado al conjunto de la bolsa.
MONTAJE/PRE OPERACIÓN ✓LISTA DE REVISIÓN ANTES DE OPERAR Y DE DISFRUTAR DE SU TRACTOR NUEVO, LE DESEAMOS QUE RECIBA EL MEJOR RENDIMIENTO Y LA MAYOR SATISFACCION DE ESTE PRODUCTO DE CALIDAD. HAGA EL FAVOR DE REVISAR LA LISTA A CONTINUACION: ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Se han completado todas las instrucciones de montaje. No quedan partes sueltas en la caja de cartón. La batería está preparada y cargada en forma adecuada. El asiento ha sido ajustado en forma cómoda y apretado en forma segura.
OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. H E D B G F A C J Fig. 14 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute. (F) INTERRUPTOR DE IGNICIÓN – Se usa para hacer arrancar o hacer parar el motor.
OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas.
OPERACIÓN PARA AJUSTAR LA ALTURA DE CORTE DE LA SEGADORA (Vea Fig. 19) PARA OPERAR EN CERROS ADVERTENCIA: No maneje hacia arriba o hacia abajo en cerros con pendientes superiores a 15° y no maneje atravesando ninguna pendiente. Utilice la guía de la pendiente proporcionada en la parte posteriora de este manual. La posición de la palanca elevadora (A) determina a qué altura se cortará el césped. A Fig. 19 Coloque la palanca elevadora en la ranura de la altura deseada.
OPERACIÓN FUNCIONAMIENTO ATRÁS (ROS) (Vea Fig. 22) PARA VACIAR LA CARGADORA (Vea Fig. 23) Tu tractor está equipado con el Sistema de Funcionamiento Atrás (ROS). Cualquier tentativa del operador de viajar marcha atrás con el embrague puesto apagará el motor a menos que la llave de ignición se ponga en la posición de “ON” del ROS. VOLCADO MANUAL ÚNICAMENTE ATENCIÓN: Ir marcha atrás con el embrague puesto para cortar, no es recomendable.
OPERACIÓN ARRANQUE CON TIEMPO FRÍO (50°F/10°C y menos) • Al hacer arrancar el motor, mantenga el control de la aceleración a la posición de estrangulación hasta que el motor se caliente y empieze funcionar mal. Una vez que empieze a funcionar mal, mueva inmediatamente el control de la aceleración a la posición rápida. El calentamiento del motor puede tomar a partir de varios segundos a varios minutos (cuanto más fría es la temperatura, más largo es el calentamiento).
MANTENIMIENTO ANTES DE CADA USO CADA 8 HORAS CADA 25 HORAS CADA 50 HORAS CADA 100 HORAS CADA ALMACENAMIENTO TEMPORADA Revisar la operación del freno T R A C T 0 R Revisar la presión de las llantas Vérifiéz la commande de présence d'opérateur et le sistema d ROS Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora 3 Tabla de lubricación Revisar el nivel 4 Limpiar la batería y los terminales Revisar el enfriamiento del transeje Limpie los residuos de la placa de dirección
MANTENIMIENTO TRACTOR PRECAUCIÓN: Usar solamente la hojas de repuesto aprobada por el fabricante de su cortacésped. Usar una hoja no aprobada por el fabricante de su cortacésped es peligroso, puede dañar su cortacésped y anular su garantía. Siempre observe las reglas de seguridad cuando dé mantenimiento.
MANTENIMIENTO PARA CAMBIAR EL ACEITE DEL MOTOR (Vea Fig. 27) CORREAS "V" Revise las correas "V" para verificar si existe deterioro y desgaste después de 100 horas de operación y cámbielas si es necesario. Las correas no son ajustables. Cambie las correas si empiezan a deslizarse debido al desgaste. Determine la gama de la temperatura esperada antes de cambiar el aceite. Todo el aceite debe cumplir con la clasificación de servicio API SG-SL. • Asegúrese que el tractor esté en una superficie nivelada.
MANTENIMIENTO FILTRO DEL AIRE LIMPIEZA Su motor puede sufrir averías y funcionar de manera incorrecta con un filtro del aire sucio. Déle servicio al filtro de aire más a menudo si se usa en condiciones polvorosas. • • LIMPIEZA DE LA REJILLA DE AIRE La rejilla de aire debe mantenerse sin mugre y paja para evitar el daño al motor debido al sobrecalentamiento. Límpiela con un cepillo de alambre o con aire comprimido para remover la mugre y las fibras de goma secas, pegadas.
SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal del embrague/freno completamente y aplique el freno de estacionamiento. • Ponga la palanca de cambios en la posición de neutro (N). • Ponga el embrague del accesorio en la posición desenganchado (DISENGAGED). • Ponga la llave de ignición en la posición de apagado (STOP) y remuévala. • Asegúrese que las cuchillas y que todas las partes movibles se hayan detenido completamente.
SERVICIO Y AJUSTES • • FIJE LOS BRAZOS DE SUSPENSIÓN LATERALES DE LA CORTADORA (A) AL CHASIS - Ubique el orificio del brazo encima de la clavija (B) que hay en la parte exterior del chasis del tractor, y fíjelo con una resorte de contención. Realice el mismo procedimiento en el otro lado del tractor. • Meta el fin de la conexión (E) en el hoyo en el suporte anterior de orificio y conecte con arandela e Retén del resorte (J). E A J F H B • Fig.
SERVICIO Y AJUSTES PARA NIVELAR LA SEGADORA AJUSTE DE DELANTE A ATRÁS (Vea Fig. 39 y 40) Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco inflados, el césped no le quedará bien cortado, lo cual podrá llevarlo a pensar que la Segadora no está bien regulada. IMPORTANTE: El piso debe quedar bien nivelado de lado a lado.
SERVICIO Y AJUSTES PARA CAMBIAR LA CORREA DE LA CUCHILLA DE LA SEGADORA (Vea Fig. 41) DESMONTAJE DE LA CORREA 1. Desmonte la segadora. (Ver “PARA DESMONTAR La segadora” en este capítulo del manual.) NOTA: Observe bien toda la correa de impulsión de movimiento, así como también la posición de las guías y los dispositivos de protección o guardacorreas. 2. Retire la correa del piñón estacionario (A) y del piñón de embrague (B). 3. Jale el cable de la correa hacia la parte de atrás del tractor.
SERVICIO Y AJUSTES REGULACIÓN DE LA POSICIÓN NEUTRO DE LA PALANCA DEL CAMBIO MECÁNICO (Vea Fig. 43) PARA AJUSTAR EL ALINEAMIENTO DEL VOLANTE DE DIRECCIÓN El cambio mecánico con diferencial y tracción anterior tiene que estar en posición neutro cuando la relativa palanca está en posición (cierre metálico.
SERVICIO Y AJUSTES REEMPLAZAR LA BATERIA (Vea Fig. 46) PARA REMOVER EL CONJUNTO DEL CAPOTA Y DEL ENREJADO (Vea Fig. 47) ADVERTENCIA: No haga cortocircuito con los terminales de la batería al permitir que una llave de tuerca o cualquier otro objeto entre en contacto con ambos terminales a la misma vez. Antes de instalar la batería remueva las pulseras de metal, los relojes de pulsera de metal, los anillos, etc.
ALMACENAMIENTO MOTOR Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA No arranca CAUSA 1. 2. 3. 4. 5. 6. 7. 3. 4. 5. 6. 7. 8. 9. Alambrado suelto o dañado. Carburador desajustado. 8. 9. 10. Difícil de arrancar CORRECCIÓN Sin combustible. Motor sin la “ESTRANGULACIÓN” (CHOKE) adecuada. Motor ahogado. Bujía mala. Filtro de aire sucio. Filtro de combustible sucio. Agua en el combustible. Válvulas del motor desajustadas. 1. 2. 10. Llene el estanque de combustible. Vea “PARA HACER ARRANCAR EL MOTOR” en la sección de operación.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA Vibración excesiva CAUSA CORRECCIÓN 1. 2. 3. Cuchilla desgastada, doblada o suelta. Mandril de la cuchilla doblado. Parte(s) suelta(s)/dañada(s). 1. 2. 3. Cambie la cuchilla. Apriete el perno de la cuchilla. Cambie la mandril de la cuchilla. Apriete la(s) parte(s). Cambie las partes dañadas. El motor continúa funcionando cuando el operador se baja del asiento con el embrague del accesorio enganchado 1.
Productos con ruedas para consumidor – Garantía limitada Husqvarna garantiza al comprador minorista original que este producto Husqvarna® carece de defectos materiales o de fabricación con un uso y mantenimiento normales desde el día de la compra, dentro del periodo de garantía aplicable indicado en el Anexo A. Esta Garantía limitada on se podrá transferir a ningún comprador posterior de este producto Husqvarna®.
8. Los daños que resultan del envejecimiento y desgaste normales o los daños por negligencia NO están cubiertos. La Garantía limitada no cubre otros daños fuera de los que resultan de defectos en el material o la mano de obra. Los siguientes NO se consideran defectos en el material o en la mano de obra y, por lo tanto, NO están cubiertos. (a) Abrasión en plataformas de cortadoras de césped. (b) Neumáticos dañados por pinchaduras externas.
Tabla de garantía limitada de 2012 para productos de consumo con ruedas Anexo A Alquiler (cualquier uso para alquiler) Consumidor (personal, solo para uso doméstico) Comercial (cualquier uso comercial, profesional, institucional, agrícola o que genere ingresos, que no sea para alquiler) 5 años * 3 años ** Sin garantía * Sin garantía ** Sin garantía * Sin garantía ** 10 años Sin garantía Sin garantía Carcasa de plataforma soldada.
Tabla de garantía limitada de 2012 para productos de consumo con ruedas Consumidor (personal, solo para uso doméstico) Producto/Componente Generadores Motor* Comercial (cualquier uso comercial, profesional, institucional, agrícola o que genere ingresos, que no sea para alquiler) * * *2 años (solo piezas en *2 años - 1365GN (solo piezas en el el 2º año) 2º año) Otros componentes perecederos* Esparcidoras Esparcidora Cortadoras de césped robóticas Cortadora de césped robótica Batería Piezas y accesorios (s
GUÍA SUGERIDA PARA MEDIR LAS PENDIENTES CON LA VISTA PARA UNA OPERACIÓN SEGURA P L E G AR A LO EST L A RGO A ES DE U N L A A PEN LÍNE DIE A P N U T NTE E DE ADA 1 5 GRA DOS SOLAMENTE ANDE CUESTA ARRIBA O CUESTA ABAJO Y NO ATRAVIESE EL CERRO 15 GRADOS MAX. ADVERTENCIA: Para evitar daños graves, haga funcionar su tractor arriba y abajo de las pendientes, nunca transversalmente con respecto a las pendientes. No cortar pendientes mayores de 15 grados.
10/25/2012 BD