Operators Manual
Table Of Contents
- Contents
- Introduction
- Safety
- Assembly
- Operation
- Maintenance
- Introduction
- Maintenance schedule
- Maintenance and checks of the safety devices on the product
- To do a check of the brake band
- To do a check of the front hand guard
- To do a check of the chain brake
- To do a check of the throttle trigger and the throttle trigger lockout
- To do a check of the chain catcher
- To do a check of the vibration damping system
- To do a check of the start/stop switch
- To do a check of the muffler
- AutoTune™
- To replace a broken or worn starter rope
- To tighten the recoil spring
- To assemble the starter housing on the product
- To clean the air filter
- To do a check of the spark plug
- To sharpen the saw chain
- To adjust the tension of the saw chain
- To do a check of the saw chain lubrication
- To do a check of the spur sprocket
- To lubricate the needle bearing
- To examine the cutting equipment
- To do a check of the guide bar
- To do maintenance on the fuel tank and the chain oil tank
- To adjust the chain oil flow
- To clean the cooling system
- Troubleshooting
- Transportation and storage
- Technical data
- Accessories
- EC Declaration of Conformity
Maintenance
Introduction
WARNING: Read and understand the safety
chapter before you do maintenance on the
product.
Maintenance schedule
Daily maintenance Weekly maintenance Monthly maintenance
Clean the external parts of the prod-
uct and make sure that there is no oil
on the handles.
Clean the cooling system. Refer to
To clean the cooling system on page
26
.
Do a check of the brake band. Refer
to
To do a check of the brake band
on page 18
.
Do a check of the throttle trigger and
throttle trigger lockout. Refer to
To do
a check of the throttle trigger and the
throttle trigger lockout on page 19
.
Do a check of the starter, starter rope
and return spring.
Do a check of the clutch centre,
clutch drum and clutch spring.
Make sure that there is no damage
on the vibration damping units.
Lubricate the needle bearing. Refer
to
To lubricate the needle bearing on
page 25
.
Clean the spark plug. Refer to
To do
a check of the spark plug on page
21
.
Clean and do a check of the chain
brake. Refer to
To do a check of the
chain brake on page 18
.
Remove burrs from the edges of the
guide bar. Refer to
To do a check of
the throttle trigger and the throttle
trigger lockout on page 19
.
Clean the external parts of the carbu-
rettor.
Do a check of the chain catcher. Re-
fer to
To do a check of the chain
catcher on page 19
.
Clean or replace the spark arrestor
mesh on the muffler.
Do a check of the fuel filter and the
fuel hose. Replace if necessary.
Turn the guide bar, do a check of the
lubrication hole and clean the groove
in the guide bar. Refer to
To do a
check of the guide bar on page 25
.
Clean the carburetor area. Do a check of all cables and connec-
tions.
Make sure that the guide bar and
saw chain are getting sufficient oil.
Clean or replace the air filter. Refer
to
To clean the air filter on page 21
.
Empty the fuel tank.
Do a check of the saw chain. Refer to
To examine the cutting equipment on
page 25
.
Clean between the cylinder fins. Empty the oil tank.
Sharpen the saw chain and do a
check of its tension. Refer to
To
sharpen the saw chain on page 22
.
Do a check of the chain drive sprock-
et. Refer to
To do a check of the spur
sprocket on page 25
.
Clean the air intake on the starter.
Make sure that nuts and screws are
tightened.
Do a check of the stop switch. Refer
to
To do a check of the start/stop
switch on page 19
.
524 - 003 - 04.06.2019 17