EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIED WITH A COPY OF THIS MANUAL. OPERATORS OF THIS EQUIPMENT MUST READ AND BE FAMILIAR WITH THE SAFETY WARNINGS. FAILURE TO OBEY WARNINGS MAY RESULT IN INJURY OR DEATH. FOLLOW INSTRUCTIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION. CONTENTS Symbol Definitions....................................................................................................................................................
Symbol Definitions Symboles Definición De Los Simbolos • • • Please read the instructions for use prior to operating the machine for the first time. Avant toute mise en service, lire attentivement la notice et se familiariser avec la machine. Antes de la puesta en marcha, lea detenidamente las instrucciones y familiaricese con la máquina.
• • • Motor Off Arrêt Du Moteur Parar El Motor • • • Use In Well Ventilated Area A Utiliser Dans Un Endroit Bien Ventilé Usar En Una Área Bien Ventilada • • • Do Not Use In Flammable Areas Ne Pas Utiliser Dans Des Ambiances Comportant Un Risque D’incendie No Usar In Áreas Inflamables • • • Machinery Hazard, Keep Hands And Feet Clear.
• • • Repairs Are To Be Done By An Authorized Dealer Only Les réparations ne peuvent être exécutées que par un distributeur agréé Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado • • • Diamond Blade Disque diamanté Sierra Diamantada • • • Blade Diameter Diamètre De Disque Diámetro De La Hoja • • • Pulley Diameter Diamètre De Poulie Diámetro De La Correa • • • Number of Revolutions Per Minute, Rotational Speed Nombre De Tours/Minutes, Vitesse De Rotation N° De Revoluci
DUST WARNING Cutting, especially when DRY cutting, generates dust that comes from the material being cut, which frequently contains silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Exposure to excessive amount of such dust can cause: • • • Respiratory diseases (affecting your ability to breath), including chronic bronchitis, silicosis and pulmonary fibrosis from exposure to silica.
DECALS & LOCATIONS ETIQUETAS Y SU UBICACIÓN AUTOCOLLANTS ET LEURS EMPLACEMENTS 542 19 07-40 (x2) Location: Both Sides of Pan 504 04 02-01 (x2) Location: Front Top Corner of Blade Guard 542 19 07-36 Location: Rip Guide 542 19 07-39 Location: Front of Pan P/N 542 04 63-27* Location: Motor Assembly
SAFETY FIRST! WARNINGS DO’s AND DO NOT’s WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. keep all guards in place and in good condition.
SAFETY FIRST! WARNINGS DO’s AND DO NOT’s WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT operate this machine unless you have read and understood this operator’s manual.
FIGURE 1 Assembly Component Identification A. B. C. D. E. F. G. H. J. K. L. L1. L2. M. N. O. P. Q. R. S. T. U. V. W. X. Y. Z. AA.
INSTRUCTION INDICATION INFORMATION Use only blades marked with a maximum operating speed greater than the blade shaft speed. Before starting up the machine, make sure you read this entire manual and are familiar with the operation of this machine. PROHIBITION WARNING The working area must be completely clear, well lit and all safety hazards removed. These signs will give advice for your safety 2 Before leaving our factory every machine is thoroughly tested.
Assembly (L) from their carton. Thread the Hose Barb (J) on the water pump outlet, hand tighten. 2. Slide the Control Valve (K) onto the flexible plastic tubing and push the open end onto the Hose Barb (J). 3. Set the Water Pump Assembly (5) in the deep end of the pan beneath the belt guard. Note: The water pump inlet screen must be submerged in order to properly pick up water. 4.
1. 3. 4. Raise the Blade Guard (M) to fully up and tighten the wing nut on the side to hold it in the raised position. Remove the Arbor Nut (O) and the Outer Blade Flange (P). Check the Blade (Q) for Counter Clockwise rotation (CCW) and install on the spindle shaft against the Inner Blade Flange (R). 4 WARNING: Read the Operating Procedure completely before operating your tile saw. Take into account the working conditions from the health and safety point of view.
5 8 ADJUSTABLE LOCKBAR WITH DEPTH LINKING PROTECTION ALIGNMENT PROCEDURES Your tile saw is factory assembled and aligned prior to shipment to ensure accurate cuts when your saw is delivered. However, since Husqvarna cannot control rough handling during shipping, it is suggested that the alignment be checked. If the saw is found in need of adjustment, refer to the appropriate section(s) below.
Parallel Alignment for Sraight Cuts The Rails determine the path the tile on the Conveyor Cart (4) travels. For a straight cut, the Cart must then travel ‘Parallel’ to the plane (or side surface) of the Blade. The path of the Conveyor Cart (4) must then be modified by adjusting the Rails to agin be Parallel to the side of the Blade. Slotted mounting holes in both ends of the Water Pan (2) are provided to allow for this adjustment. Tip: Align only one Rail first; usually the Inner Rail.
12 WATER PUMP TROUBLE-SHOOTING PROCEDURE If Water Stops Flowing, 1. Stop Sawing, then 2. Disconnect Electrical Plug from Outlet, then 3. Remove the Pump, then 4. Back Flush. Back flushing is done by forcing water into the pump discharge and out through the screen. Most of the time this procedure works, and the pump can be put back into service.
15 TILE CUTTING ACCESSORIES ANGLE GUIDE Parts List: PROTRACTOR Diag. 1 2 3 4 5 6 Part No. 542 05 01-04* 542 05 01-07* 542 05 01-05* 542 05 01-06* 542 05 01-03* 542 18 97-37* Qty. 1 1 1 1 1 2 7 8 9 542 05 10-20* 542 18 97-37* N/A 1 1 1 MITY MITRE GUIDE Description Frame, Miter Bar, Locking Clip, Stop Spring Knob Knob, 1/4”-20 x 1” Miter Assy, 45° Knob, 1/4”-20 x 1” Sector Plate BULLNOSE FOLDING STAND Diag. 10 11 12 13 14 15 Part No.
Diagram 1: Wiring Diagram 542 20 30-79, 1.5HP, 115V/60/1 NOTE: Motors used on this unit are manufactured by Baldor Electric Company. For any motor servicing or warranty work, the motor must be taken to a Baldor Authorized Service Center. The Service Center nearest you can be found on the Internet under www.balder.com/support/. If access to the Internet is not available, contact us at the Customer Service listed on teh back cover of this manual.
Diagram 2: Wiring Diagram 542 00 06-05, 1.
NOTES: NOTAS: REMARQUE : 20
Corporate Office 17400 West 119th Street Olathe, Kansas 66061 USA Customer Service: 800-288-5040 Customer Serv. Fax: 800-825-0028 Corporate Office: 913-928-1000 Corp. Office Fax: 913-438-7951 International Customer Service: 913-928-1300 Customer Serv. Fax: 913-438-7938 www.husqvarna.com Please record the Date of Purchase and the Serial Number, the Model Number of the equipment and the Date of Purchase of your equipment in the space below. When ordering service items, please have this information available.