Operator′s manual Manuel d’utilisation Manual de instrucciones Cultivator attachment CA 150 Accessoire de cultivateur CA 150 Accesorio de cultivador CA 150.
KEY TO SYMBOLS Symbols Other symbols/decals on the machine refer to special certification requirements for certain markets. WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
CONTENTS Contents KEY TO SYMBOLS Symbols ....................................................................... CONTENTS Contents ...................................................................... Note the following before starting: ................................ SAFETY INSTRUCTIONS Personal protective equipment ..................................... Machine′s safety equipment ........................................ General safety precautions ..........................................
SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment. ! WARNING! Listen out for warning signals or shouts when you are wearing hearing protection. Always remove your hearing protection as soon as the engine stops.
SAFETY INSTRUCTIONS ! ! WARNING! Always stop the engine before doing any work on the cutting attachment. This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it. WARNING! Never use a machine with faulty safety equipment. The machine’s safety equipment must be checked and maintained as described in this section.
SAFETY INSTRUCTIONS General working instructions • When the engine is switched off, keep your hands and feet away from the blades until they have stopped. • Make sure your hands and feet do not come near the cutter when the engine is running. • Always keep the tines close to the ground. • Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine (i.e.
WHAT IS WHAT? 6 1 2 7 3 8 4 5 What is what on the cultivator attachment? 1 Blade guard 5 Cotter pin 2 Shaft 6 Grease filler cap, bevel gear 3 Blades 7 Bevel gear 4 Split pin 8 Operator′s manual English –7
ASSEMBLY Fitting the bevel gear • • Guide the guard B onto the shaft so that the hole in the guard aligns with the hole in the bracket. Tighten the screws C. B Assembling the angle gear on the shaft. Turn the shaft so that the splines on the drive axle mate in the angle gear. 4xC • • Align the bracket with guard so that it sits straight in relation to the tines. • Tighten the screws F. First tighten the screw H and then the screw M. M H Assembling the guard.
STARTING AND STOPPING Check before starting For safety reasons follow these recommendations! • Inspect the working area. Remove any objects that could be thrown out. • Check that the machine is in perfect working order. Check that all nuts and screws are tight. • Check the tines and tine guard to ensure they are undamaged and show no signs of cracking. Replace the tine and tine guard if they have been exposed to impact or are cracked.
MAINTENANCE Bevel gear Replace the tine with a new and assemble in the reverse order. The bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you should check that the bevel gear is filled three-quarters (40g) full with grease. Use HUSQVARNA special grease. Maintenance schedule Below you will find some general maintenance instructions. If you need further information please contact your service workshop.
TECHNICAL DATA Technical data Technical data CA 150 Weight Weight, Lbs/kg 2,9 Blades Diameter tines, mm 220 Working width, mm 150 Tine speed at engine speed 10,500 r/min 215 English – 11
1150001-20 ´®z+RÆ,¶0n¨ ´®z+RÆ,¶0n¨ 2004-11-10
