GB Operator’s manual Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Manual de ES instrucciones Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina. DE Bedienungsanweisung Lesen Sie die Bedienungsanweisung sorgfältig durch und machen Sie sich mit dem Inhalt vertraut, bevor Sie das Gerät benutzen.
KEY TO SYMBOLS Symbols on the machine: Symbols in the operator’s manual: WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Inspection and/or maintenance shall be carried out with the motor switched off and the plug to the power unit disconnected. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ............................................. Symbols in the operator’s manual: ............................... CONTENTS Contents ...................................................................... WHAT IS WHAT? What is what on the wall saw? ..................................... SAFETY INSTRUCTIONS Steps before using a new wall saw .............................. Personal protective equipment .....................................
WHAT IS WHAT? What is what on the wall saw? 1 Saw unit 12 Blade guards 2 Cutting arm 13 Track 3 Propulsion engine, blade 14 Saw carriage 4 Cable connection 15 Locking handle 5 Protective cover 16 Wall mounting 6 Handle/blade guard mount 17 Track holder 7 Hose connection, water in 18 Connector 8 Water hose 19 Cleaning brush 9 Blade flange hub 20 Tool kit 10 Outer blade flange 11 Blade guard guide 4 – English 21 Operator′s manual
SAFETY INSTRUCTIONS Steps before using a new wall saw • Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. • This machine is only intended for use together with a Husqvarna PP 440 HF. All other use is forbidden. • Read through the manual supplied with the power unit before starting to use the machine. • The machine can cause serious personal injury. Read the safety instructions carefully. Learn how to use the machine.
SAFETY INSTRUCTIONS General safety precautions Transport and storage Do not use the machine without first reading and understanding the contents of this Operator’s Manual. • Always switch of the power unit and pull out the electric cable before moving the equipment. • Dismount the blade and blade guard before transport and storage. • Store the equipment in a lockable area so that it is out of reach of children and unauthorised persons.
SAFETY INSTRUCTIONS • Always check and mark out where gas pipes are routed. Cutting close to gas pipes always entails danger. Make sure that sparks are not caused when cutting in view of the risk of explosion. Remain concentrated and focused on the task. Carelessness can result in serious personal injury or death. • Make sure that no pipes or electrical cables are routed in the area to be cut. • Check that electrical cables within the working area are not live.
PRESENTATION WS 440 HF General • The powerful, water-cooled electric motor produces an impressive 13 kW to the spindle, even though the saw weighs just 25 kg (55 lbs). • The spindle speed is electrically adjustable and can be operated from the power unit´s remote control. • Short distance between blade and track, for a straighter cut. • Slip clutch for all movable components. • The blade direction and the direction of the water spray can be operated from the power unit´s remote control.
ASSEMBLY Mount wall mountings and rail Mount the saw carriage and saw Fit the wall mounting as set out below: 1 Mark off the cutting line and mark off the expander bolts holes 165 mm (6.5") from the cutting line. 2 Drill 15 mm (5/8”) holes for the M12 (1/2”) expander bolts. 3 Hang the wall mountings loosely from the expander bolts, using M6S 12 x 70 (1/2”x2”) or similar. 4 Place the rail in the wall mountings and tighten the compression washers.
ASSEMBLY Fit the blade ! WARNING! Never mount or dismount the blade or blade guard without first pulling out the power cable running to the saw unit. Carelessness can result in serious personal injury or even death. 1 Start by removing any dirt from the contact surfaces on the blade flange and blade. 2 Check the blade’s direction of rotation. The blade shall rotate with the exposed part of the diamond in the rotational direction of the blade.
ASSEMBLY Fit the blade guard ! 1 4 To remove the guard, release the latch and pull the handle upwards and inwards to the guard. Lock the plastic heel on the upper stay. 5 Connect the water hose from the out-coupling on the saw motor to the in-coupling on the blade flange hub. WARNING! Never mount or dismount the blade or blade guard without first pulling out the power cable running to the saw unit. Carelessness can result in serious personal injury or even death.
STARTING AND STOPPING Before starting • Enclose the area to be cut so that unauthorised persons can not be injured or disturb the operator. • Check that the blade and th blade guard is not damaged or cracked. Replace the blade or the blade guard if it is exposed to impact or is cracked. • Check that all cables and the water supply are correctly connected to the machine before starting it.
SETTINGS AND ADJUSTMENTS Adjusting the guide wheels Adjust the saw carriage In order for the saw to run stably and saw a straight cut, the four guide wheels must rest against the rail and not have too much play. When there is too much play between the saw carriage and rail the guide wheels must be adjusted: As the saw wears, after a number of hours working, it can be a good idea to ensure that the saw sits firmly in the saw carriage and rail.
MAINTENANCE Service Lubrication of feeder gears IMPORTANT! If the gears are not lubricated regularly, their lifespan will shorten considerably. IMPORTANT! All types of repairs may only be carried out by authorised repairmen. This is so that the operators are not exposed to great risks. There are two grease nipples on every saw unit. Through these the gears for the feeding engines can be lubricated. Lubricate daily or at least every 30 hours of operation.
TECHNICAL DATA WS 440 HF Weight Saw carriage, kg/lbs Saw unit, kg/lbs Blade guard 800 mm, kg/lbs Blade guard 1000 mm, kg/lbs Track 1200 mm (47”) kg/lbs Track 2000 mm (79”) kg/lbs 3,7/8,2 25/55,1 13/28,7 16/35,3 9,5/20,9 19/41,9 Blade size Blade size - max, mm/inches Blade size - min, mm/inches Starting blade - max, mm/inches 1200/47,2 600/23,6 1000/39,4 Saw depth - max, mm/inch 530/20,9 Motor for saw blade drive Spindle output - max, kW Power train Output speed, rpm Feedingsystem/control PM High cycl
TECHNICAL DATA EC-declaration of conformity Husqvarna Construction Products, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the wall sawHusqvarna WS 440 HF , from 2008´s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), conforms with the requirements of the COUNCIL´S DIRECTIVE: • of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
www.husqvarnacp.