Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Vous pouvez utiliser de l’essence contenant jusqu’à 10 % d’éthanol (E10) avec cet appareil. L’utilisation d’essence contenant plus de 10 % d’éthanol annulera la garantie du produit.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN • • WARNING. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy of Pediatrics recommends that children be a minimum of 12 year of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of age before operating a riding lawn mower. If fuel is spilled on clothing, change clothing immediately. Never overfill fuel tank. Replace gas cap and tighten securely.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 2.5 Gallons/9,46 L Regular Unleaded Oil Type: (API: SG-SL) SAE30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: 67 Oz./2,0 L Spark Plug: NGK BPR4ES (Gap: .030"/0.76 mm) Charging System: 15 Amps @3600 RPM Battery: Amp/Hr: Min. CCA: Case size: Blade Bolt Torque: CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance.
UNASSEMBLED PARTS Keys Slope Sheet Battery *Installed by Dealer (2) Hex Bolts *Brush Guard Kit (2) Nut Keps *Pedal (2) Keys (1) Oil Drain Tube (2) Screw (2) Nut U-Channel (1) Quick Connect ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY LABEL A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY ✓CHECKLIST NOTE: You may now roll your tractor off the skid. Continue using the instructions that follow to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Ensure tractor is in a well-ventilated area. Ensure the area in front of tractor is clear of other people and objects.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. D P Z G H E F N B A Q C J K M L Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR ENGINE • Move throttle control (D) between half and full speed (fast) position.
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 7) The cutting height range is approximately 1 to 4" (25,4 to 101,6 mm). The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. The direction and speed of movement is controlled by the forward and reverse drive pedals. • Start tractor and release parking brake.
OPERATION TO STOP MOWER BLADES TO OPERATE ON HILLS Disengage attachment clutch control. CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector chute in place (See Fig. 10). • • • • • • Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills.
OPERATION SERVICE REMINDER/HOUR METER CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season.
OPERATION COLD WEATHER STARTING (50°F/10°C and below) • When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (models
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.
MAINTENANCE V-BELTS TO CHANGE ENGINE OIL (See Fig. 16 - 18) Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container.
MAINTENANCE ENGINE OIL FILTER IN-LINE FUEL FILTER (See Fig. 19) Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. • With engine cool, remove filter and plug fuel line sections. • Place new fuel filter in position in fuel line with arrow pointing towards carburetor.
MAINTENANCE DECK WASHOUT PORT (See Fig. 21) Your tractor’s deck is equipped with a washout port as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig. 22) • • • • • • TO INSTALL MOWER (See Fig.
SERVICE AND ADJUSTMENTS • • From right side of mower, first insert 90° end of anti-sway bar (S) into hole in transaxle bracket (T), located near left rear tire in front of transaxle. NOTE: Flashlight may be helpful. ANTI-SWAY BAR (S) LOCATION • ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring. Repeat on opposite side of tractor.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER FRONT-TO-BACK ADJUSTMENT (See Figs. 32 & 33) IMPORTANT: Deck must be level side-to-side. Ensure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT • MOWER DRIVE BELT REMOVAL (See Fig. 34) • Park tractor on a level surface. Engage parking brake. • Lower attachment lift lever to its lowest position. • Remove mandrel covers. • Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface. • With a 3/8" breaker bar and using the square opening in the idler arm, shift the arm counterclockwise ( ) to relieve the tension on the belt.
SERVICE AND ADJUSTMENTS 5. Reinstall anti-rotation link (B) on right side of tractor. Tighten securely. 6. Reconnect clutch harness (A). 7. Make sure belt is in all pulley grooves and inside all belt guides and keepers. 8. Install mower (See “TO INSTALL MOWER” section in this manual). TO REPLACE MOTION DRIVE BELT (See Fig. 37) Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL 1.
SERVICE AND ADJUSTMENTS TO START ENGINE WITH A WEAK BATTERY (See Fig. 39) REPLACING BATTERY (See Fig. 40) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. WARNING: Lead-acid batteries generate explosive gases.
SERVICE AND ADJUSTMENTS TRANSMISSION TO REPLACE HEADLIGHT BULB • • • • Raise hood. Pull bulb holder out of the hole in the backside of the grill. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. Close hood. REMOVAL/REPLACEMENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMISSION” in the Operation section of this manual.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION 8. Loose or damaged wiring. 9. Engine valves out of adjustment. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8. Check all wiring. 9. Contact an authorized service center/department. Hard to start 1. 2. 3. 4. 5. 6. 7. Dirty air filter.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA L O NG D THIS O I T S T A E D LIN 1 5 DEG E RE E S LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. • Nunca dejar una máquina encendida sin vigilancia.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles III. NIÑOS • • ADVERTENCIA: LOS NIÑOS PUEDEN SUFRIR DAÑOS CON EL USO DE ESTE EQUIPO. La Academia Estadounidense de Pediatría (American Academy of Pediatrics) recomienda que sólo se permita a niños con una edad mínima de 12 años manejar máquinas cortacésped manuales, y al menos de 16 años para manejar tractores cortacésped.
SPÉCIFICATIONS DE PRODUIT FELICITACIONES por la compra de su tractor. Ha sido diseñado, planificado y fabricado para darle la mejor confiabilidad y el mejor rendimiento posible. Capacité et le type d’essence: 9,46 L /2.5 Gallons L’essence sans plomb normale Type d’huile (API: SG-SL): SAE30 (supérieure de 32°F/0°C) SAE 5W30 (inférieure de 32°F/0°C) Capacité d’huile: 2,0 L/67 Oz.
PIÈCES PAS ASSEMBLÉ Batterie Clé Guide-pente *Posé par le Concessionnaire (2) Boulon *Jeu de protecteur (2) Écrou (2) Clés (1) Tube de Vidange *Pédale (2) Vis (1) Connecter d'accouplement du rapide (2) Écrou “U” MONTAGE Votre nouveau tracteur a été monté à l’usine sauf les pièces qui ne sont pas montées pour l’expédition. LES OUTILS EXIGÉS POUR LE MONTAGE DE VOTRE TRACTEUR ÉTIQUETTE Un jeu de clé à douille rendra le montage. Les dimensions normales des clés sont inscrites.
MONTAGE ✓LISTE DE CONTRÔLE REMARQUE: Vous pouvez maintenant faire rouler le tracteur hors de la plateforme. Suivez les instructions ci-après pour retirer le tracteur de la plateforme. AVANT D’UTILISER VOTRE TRACTEUR, NOUS VOULONS NOUS ASSURER QUE VOUS RECEVREZ LE MEILLEUR RENDEMENT DE CE PRODUIT DE QUALITÉ ET QUE VOUS EN SEREZ SATISFAIT. AVERTISSEMENT: Avant le démarrage, nous vous prions de lire, comprendre et suivre toutes les instructions dans la section Fonctionnement de ce manuel d’instructions.
UTILISATION Ces symboles peuvent se montrer sur votre tracteur ou dans les publications fournies avec le produit. Apprenez et comprenez la signification des symboles.
UTILISATION CONNAISSEZ VOTRE TRACTEUR AVANT D'UTILISER VOTRE TRACTEUR, LISEZ CE MANUEL DE L’OPÉRATEUR ET LES REGLES DE SECURITE Comparez les illustrations ci-dessous à celles de votre tracteur afin de vou familiariser avec l'emplacement des différentes commandes et avec les réglages. Gardez ce manuel pour référence . D P Z G H E F N B A Q C J K M L Fig. 3 Nos tracteurs conforment aux normes de sécurité de l’American National Standards Institute.
UTILISATION L’utilisation d’un tracteur présente le risque de projection des particules dans les yeux qui peuvent causer des blessures sérieuses. Portez toujours des lunettes de sécurité ou une visière pendant que vous utilisez, ou que vous faites des réglages ou des réparations au tracteur. Nous recommandons des lunettes de sécurité ou un masque large de sécurité porté au-dessus des lunettes. POUR ENGAGER LE FREIN DE STATIONNEMENT (Voir la Fig.
UTILISATION POUR AVANCER ET POUR RECULER (Voir la Fig. 7) • Placez le levier d’accrochage dans la rainure correspondant à la hauteur désirée. La plage de réglage de la hauteur de coupe est environ de 25,4 à 101,6 mm (1 à 4 po.). Les hauteurs sont mesurées du terrain à l’extrémité de la lame quand le moteur ne marche pas. Ces hauteurs sont approximatives et elles pourraient changer à cause des conditions du terrain, de la hauteur de l’herbe et des types d’herbe qui sont tondus.
UTILISATION POUR ARRÊTER LES LAMES DE TONDEUSE POUR UTILISER DANS LES PENTES Déplacez la commande d’embrayage d’accessoire à la position "DÉBRAYÉE". AVERTISSEMENT: N’utilisez jamais le tracteur dans les côtes de plus de 15°. Ne le conduisez jamais en travers des surfaces en pente. ATTENTION: N’utilisez pas la tondeuse sans le déflecteur ou sans le ramasse-herbe s'il y a lieu (Voir La Fig. 10). • • • • • • Choisissez la vitesse la plus lente avant de commencer à monter ou descendre une côte.
UTILISATION INDICATEUR D’ENTRETIEN/HOROMÈTRE ATTENTION: Les carburants contenant de l’alcool (appelés essence-alcool, ou gazohol, ou contenant de l’éthanol ou du méthanol) peuvent attirer l’humidité et conduire à une séparation et à la formation d’acides durant le remisage. Le gaz acide peut endommager le circuit de carburant d’un moteur pendant son remisage. Pour éviter tout problème au niveau du moteur, videz le circuit de carburant avant de remiser la machine pour une période de 30 jours ou plus.
UTILISATION DÉMARRAGE PAR TEMPS FROID (50°F/10°C et moins) • 8. Avancez le tracteur de 1,5 m (5 pieds) approximativement et ensuite, reculez de 1,5 m (5 pieds). Répétez ce procédé de conduire trois (3) fois. Votre tracteur est maintenant purgé et prêt pour l’utilisation normale. Quand vous démarrez le moteur, enfoncez doucement la commande d'étrangleur jusqu'à ce que le moteur marche bien.
ENTRETIEN AVANT CHAQUE TOUTES LES USAGE 8 HEURES GUIDE D’ENTRETIEN TOUTES LES 25 HEURES TOUTES LES 50 HEURES TOUTES LES 100 HEURES CHAQUE SAISON AVANT L’ENTREPOSAGE Vérifiez le système de frein Vérifiez la pression des pneus Vérifiez le système de présence d'opéateur et le système del “ROS” Vérifiez l'inté grité des systèmes de fixation Affilez/Remplacez les lames de tondeuse 3 Tableau de lubrification Vérifiez le niveau de batterie 4 Nettoyez la batterie et les bornes Nettoyez de la plaque de di
ENTRETIEN TRACTEUR DANGER: N’utilisez que les lames de rechange autorisée par le fabricant de votre tondeuse. L’usage d’une lame n’ayant pas été autorisée par le fabricant de votre tondeuse est dangereux et risque d’endommager votre tondeuse et d’annuler sa garantie. Observez toujours les règles de sécurité quand vous faites l’entretien.
ENTRETIEN COURROIES TRAPÉZOÏDALES DÉPOSE DU COUVERCLE DU TABLEAU DE COMMANDE INFÉRIEUR • Soulevez le capot. • Retirez l’attache du couvercle du tableau de commande inférieur. PRÉCAUTION: Retirez avec soin le couvercle du tableau de commande inférieur en portant attention à ne pas briser les pattes de fixation du couvercle.
ENTRETIEN FILTRE D’ESSENCE INSTALLÉ EN LIGNE (Voir la Fig. 19) FILTRE D’HUILE DE MOTEUR Remplacez le filtre d’huile de moteur chaque saison ou tous les deux (2) changements d’huile si le tracteur a été utilisé plus de 100 heures dans une (1) année. REMARQUE: S'il y a lieu, enlevez les déposes du tableau de commande inférieur à l'aide des étapes décrites dans la section "Dépose du couvercle du tableau de commande inférieur" de ce manuel. Le filtre d’essence devrait être remplacé au moins chaque saison.
ENTRETIEN RACCORD DE LAVAGE DU PLATEAU DE COUPE (Voir La Fig. 21) Le plateau de coupe de votre tracteur est équipé d’un raccord de lavage qui fait partie du système de lavage du plateau de coupe. Il convient de l’utiliser après chaque usage. 1. Conduisez le tracteur vers un endroit plat et dégagé de votre pelouse, suffisamment près pour atteindre le robinet d’eau destiné au tuyau d’arrosage de votre jardin.
RÉVISION ET RÉGLAGES ADVERTISSEMENT: POUR ÉVITER DES DOMMAGES SÉRIEUX, AVANT DE FAIRE TOUS LES RÉVISIONS OU RÉGLAGES. • • • • • Appuyez sur la pédale de frein et engagez le frein de stationnement. Placez l’embrayage d’accessoire en position débrayée (DISENGAGED). Tournez la clé de contact à la position d’arrêt (STOP) et enlevez-la. Assurez-vous que les lames et toutes les pièces tournantes se soient arrêtées.
RÉVISION ET RÉGLAGES • Depuis le côté droit de la tondeuse, insérer d‘abord l’extrémité 90° de la barre stabilisatrice (S) dans le trou du support boîtepont (T), se trouvant près du pneu arrière gauche devant la boîte-pont. REMARQUE: Une lampe torche peut être utile. • • ATTACHEZ LES BIELLES ARRIÈRES (C) – Soulevez le coin arrière de la tondeuse et positionnez la rainure du bras sur la tige (D) du support arrière de la tondeuse et fixez fermement à l’aide d’une rondelle et d’un ressort-arrêtoir.
RÉVISION ET RÉGLAGES POUR AJUSTER LE NIVEAU LA TONDEUSE AJUSTEMENT AVANT/ARRIÈRE (Voir les Figs. 32 et 33) IMPORTANT: La plateforme doit être au même niveau d’un côté et de l’autre. Pour obtenir de meilleurs résultats, les lames de la tondeuse doivent être ajustées de sorte que la pointe avant est 3,1 to 9,5 mm (1/8 à 3/8 po.) inférieure à la pointe arrière lorsque la tondeuse est à sa position la plus élevée. Assurez-vous que les pneus soient gonflés jusqu’à la pression en PSI indiquée sur ceux-ci.
RÉVISION ET RÉGLAGES POUR REMPLACER LA COURROIE DE LAME DE TONDEUSE • ENLEVER LA COURROIE (Voir Figs. 34) • • • • • • • • • Stationnez le tracteur sur une surface de niveau. Actionnez le frein de stationnement. Enlever les caches du mandrin. Enlever la plaques du repose-pieds et le cache mandrin. Enlever toutes saletés ou gazon coupé qui auraient pu s'accumuler autour des mandrins et sur la surface entière du plateau supérieur.
RÉVISION ET RÉGLAGES POUR REMPL ACER L A COURROIE D’ENTRAÎNEMENT (Voir la Fig. 37) 6. Installez de nouveau la bielle anti rotation (B) à la droite du tracteur. Serrez fermement. 7. Branchez de nouveau le faisceau de câbles de l’embrayage (A). 8. Assurez-vous que la courroie est bien en place dans les rainures des poulies, ainsi que les guides et les dispositifs de retenue. Installez la tondeuse (voir « POUR INSTALLER LA TONDEUSE » dans la présente section du manuel).
RÉVISION ET RÉGLAGES POUR DÉMARRER LE MOTEUR AVEC UNE BATTERIE FAIBLE (Voir la Fig. 39) REPLACER LA BATTERIE (Voir la Fig. 40) AVERTISSEMENT: Ne court-circuitez pas les bornes de batterie par permettre qu'une clé ou autres objets entrent en contacte avec les deux bornes a la même fois. Avant d’ins tal ler la batterie, enlevez tous les bijoux, les bracelets de montre, les bagues métalliques, etc. Au début la borne positive doit être branchée pour prévenir les étincelles d’une mise à la masse accidentelle.
RÉVISION ET RÉGLAGES TRANSMISSION VERROUS ET RELAIS Un câblage desserré ou avarié peut être la cause du mauvais fonctionnement, de l'arrêt ou du non-démarrage du tracteur. • Vérifiez le câblage. ENLEVEMENT/REMPLACEMENT Si votre transmission doit être retirée pour un entretien ou pour être remplacée, elle doit être purgée après avoir été réinstallée et avant de faire fonctionner le tracteur. Voir “PURGEZ LA TRANSMISSION” dans la section Utilisation de ce manuel.
ENTREPOSAGE MOTEUR Préparez immédiatement votre tracteur pour l’entreposage à la fin de la saison ou si le tracteur ne sera pas utilisé pendant une période de 30 jours ou plus. SYSTÈME D’ESSENCE IMPORTANT: C’EST TRÈS IMPORTANT D’ÉVITER LA FORMATION DES DÉPÔTS DE GOMME DANS LE CARBURATEUR, LE FILTRE D’ESSENCE, LE TUYAU D’ESSENCE OU LE RÉSERVOIR D’ESSENCE PENDANT L’ENTREPOSAGE.
GUIDE DE DÉPANNAGE PROBLÈME Le moteur refuse de démarrer CAUSE CORRECTION 1. 2. Sans essence. Le moteur n’est pas démarré à froid correctement. 1. 2. 3. 4. 5. 6. 7. Le moteur est noyé. Mauvaise bougie d’allumage. Filtre à air sale. Filtre d’essence sale. II y a de l’eau dans l’essence. 3. 4. 5. 6. 7. 8. 9. Le câblage est lâche ou endommagé. Les soupapes de moteur demandent un réglage. 8. 9. 1. 2. 3. 4. 5. Filtre à air sale. Mauvaise bougie d’allumage. Batterie faible ou à plat.
GUIDE DE DÉPANNAGE PROBLÈME CAUSE Le moteur marchelorsque le conducteur quitte le siège avec l’embrayage d’accessoire engagé 1. Coupe inégale 1. 2. 3. 1. 2. 3. 4. Mauvaise déchargede l’herbe 1. Vérifiez le câblage, les interrupteurs et les connexions.Si le problème n’est pas corrigé, contactez un centred’entretien autorisé. ATTENTION : n’utilisez pas la machine avant d’avoir corrigé le problème. 4. 5.
GUIDE SUGGÈRE POUR L'ÉVALUATION DES PENTES AFIN D'AMÉLIORER LA SÉCURITÉ D'UTILISATION PLIE Z S UIVA CEC N I T E L S E T S PO UNE I N P T E I N L T LÉS E A 15 D E GRÉ S TONDEZ LES PENTES EN MONTANT OU EN DESCENDANT MAIS, JAMAIS EN TRAVERS 15 DEGRÉS MAX 57
SERVICE NOTES/ REMARQUES D’ENTRETIEN 58
SERVICE NOTES/ REMARQUES D’ENTRETIEN 59
09/12/2013 BD