Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto. the product warranty.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN • • WARNING. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy of Pediatrics recommends that children be a minimum of 12 year of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of age before operating a riding lawn mower. If fuel is spilled on clothing, change clothing immediately. Never overfill fuel tank. Replace gas cap and tighten securely.
PRODUCT SPECIFICATIONS Gasoline Capacity And Type: 3.0 Gallons/11,35 L Unleaded Regular Oil Type (Api: Sg-Sl): SAE 30 (Above 32°F/0°C) SAE 5W30 (Below 32°F/0°C) Oil Capacity: w/Filter 64 oz./1.96 L w/o Filter 52 oz./1.50 L Spark Plug: NGK BPR4ES (Gap: .030"/0.76Mm) Charging System: 15 Amps @ 3600 Rpm Battery: Amp/Hr: Min. Cca: Case Size: Blade Bolt Torque: CONGRATULATIONS on your purchase of a new tractor.
UNASSEMBLED PARTS Keys Slope Sheet *Installed by Dealer *Brush Guard Kit *Pedal (1) Quick Connect Key(s) (2) Screw (2) Nut U -Channel ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY ADJUST SEAT (See Fig. 2) • • A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) 1/2" wrench Tire pressure gauge (2) 7/16" wrenches Utility knife Pliers • Sit in seat.
ASSEMBLY ✓CHECKLIST CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ENSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. H P Z S G D E N B F A Q K C J M L Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR ENGINE • Move throttle control (D) to slow position.
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 7) • Put attachment lift lever in desired cutting height slot. The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months.
OPERATION TO STOP MOWER BLADES TO OPERATE ON HILLS Disengage attachment clutch control. CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector chute in place (See Fig. 10). • • • • • • Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills.
OPERATION BEFORE STARTING THE ENGINE SERVICE REMINDER/HOUR METER Service reminder shows the total number of hours the engine has run and indicates when the engine or mower needs servicing. After every 50 hours of operation the oil can icon will stay on for 2 hours or until a manual reset occurs. To reset the display manually turn the ignition switch to the on position, then the off position five times (1 second on, 1 second off). To service engine and mower, see the Maintenance section of this manual.
OPERATION TO START ENGINE (See Fig. 3) PURGE TRANSMISSION When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brake. • Move attachment clutch to “DISENGAGED” position. • Move throttle control to choke position.
OPERATION MOWING TIPS • • • • • DO NOT use tire chains when the mower housing is attached to tractor. Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. The left hand side of mower should be used for trimming. Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (models
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.
MAINTENANCE V-BELTS TO CHANGE ENGINE OIL (See Fig. 17 - 19) Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container.
MAINTENANCE IN-LINE FUEL FILTER (See Fig. 20) ENGINE OIL FILTER The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. • With engine cool, remove filter and plug fuel line sections. • Place new fuel filter in position in fuel line with arrow pointing towards carburetor. • Be sure there are no fuel line leaks and clamps are properly positioned. • Immediately wipe up any spilled gasoline.
MAINTENANCE DECK WASHOUT PORT (See Fig. 22) Your tractor’s deck is equipped with a washout port as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig. 23) TO INSTALL MOWER (See Figs.
SERVICE AND ADJUSTMENTS • • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. Repeat on opposite side of tractor. • • ATTACH FRONT LINK (E) - Work from left side of tractor. Insert rod end of link assembly through front hole in tractor front suspension bracket (F). Insert end of link (E) into hole in front mower bracket (H) and secure with washer and retainer spring (J). A E B J F H Fig.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see step in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 31 & 32) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 33) TO REPLACE MOTION DRIVE BELT (See Fig. 34) MOWER DRIVE BELT REMOVAL • Park tractor on a level surface. Engage parking brake. • Lower attachment lift lever to its lowest position. • Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface. • Remove belt from electric clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (V). Park the tractor on level surface.
SERVICE AND ADJUSTMENTS FRONT WHEEL TOE-IN/CAMBER TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully charged battery. • RED cable last from both batteries. Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center. TO REMOVE WHEEL (See Fig. 35) • • Block up axle securely.
SERVICE AND ADJUSTMENTS TO REPLACE HEADLIGHT BULB • • • • TRANSMISSION Raise hood. Pull bulb holder out of the hole in the backside of the grill. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. Close hood. REMOVAL/REPLACEMENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMISSION” in the Operation section of this manual.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ES SENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION 8. Loose or damaged wiring. 9. Engine valves out of adjustment. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8. Check all wiring. 9. Contact an authorized service center/department. Hard to start 1. 2. 3. 4. 5. 6. 7. Dirty air filter.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck.
SERVICE NOTES 29
1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
Consumer Wheeled Products - Limited Warranty Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred to any subsequent purchaser of this Husqvarna® product. Certain components (e.g.
(a) Abrasion to mower decks; (b) Tires damaged by external punctures; (c) Natural discoloration of materials due to ultraviolet light; (d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures; In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including any of the following: (e) Failure to provide or perform required maintenance services as prescribed
Consumer Wheeled Limited Warranty Chart 2013 Product/Component Riding Lawn Tractors: Frame, Chassis, Front Axle Engine* Transmission (if made by Husqvarna/Peerless) Transmission (if third party)** XLS Models only - stamped deck shell.
Consumer Wheeled Limited Warranty Chart 2013 Consumer (personal, household use only) Commercial (any commercial, professional, institutional, agricultural, or income producing use, other than Rental Use) 1 Year 90 days No Warranty No W arranty Product/Component Parts & Accessories (if purchased) Accessories (e.g., grass catcher, bumper guard accessories, etc. Parts (e.g., belts, blades, etc.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles III. NIÑOS • • ADVERTENCIA: LOS NIÑOS PUEDEN SUFRIR DAÑOS CON EL USO DE ESTE EQUIPO. La Academia Estadounidense de Pediatría (American Academy of Pediatrics) recomienda que sólo se permita a niños con una edad mínima de 12 años manejar máquinas cortacésped manuales, y al menos de 16 años para manejar tractores cortacésped.
ESPECIFICACIONES DEL PRODUCTO Capacidad y Tipo de gasolina: 3.0 Galones/11,35 L Regular Sin Plomo Tipo de Aceite: (API: SG-SL) SAE 30 (Sobre 32°F/0°C) SAE 5W30 (Debajo 32°F/0°C) FELICITACIONES por la compra de su tractor. Ha sido diseñado, planificado y fabricado para darle la mejor confiabilidad y el mejor rendimiento posible.
PIEZAS SIN MONTAR Llaves *Instalado por el distribuidor Hoja de pendiente *Juego de cubierta *Pedal Llaves (1) Accesorio del conexión (2) Tornillo (2) Tuerca de canal MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío. HERRAMIENTAS NECESARIAS PARA EL MONTAJE PARA AJUSTAR EL ASIENTO (Vea Fig. 2) 1. 2. Un juego de llaves de tubo facilitará el montaje. A continuación se enumeran los tamaños de las llaves estándar.
MONTAJE ✓LISTA DE REVISIÓN REVISIÓN DE LA PRESIÓN DE LAS LLANTAS Las llantas en su unidad fueron infladas demasiado en la fábrica por razones de envío. La presión de las llantas correctas es importante para obtener el mejor rendimiento en el corte. • ANTES DE OPERAR Y DE DISFRUTAR DE SU TRACTOR NUEVO, LE DESEAMOS QUE RECIBA EL MEJOR RENDIMIENTO Y LA MAYOR SATISFACCION DE ESTE PRODUCTO DE CALIDAD. Reduzca la presión de los neumáticos a la PSI que se indica en estos.
OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. H P Z S G D E N B F A Q K C J M L Fig. 3 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute.
OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas.
OPERACIÓN PARA AJUSTAR LAS RUEDAS CALIBRADORAS (Vea Fig. 9) Las ruedas calibradoras están bien ajustadas cuando se encuentran un poco a distancia del terreno al mismo tiempo que la segadora esté a la altura de corte deseada. Entonces las ruedas calibradoras mantienen el conjunto segador en posición para prevenir el corte raspeo en casi todos los terrenos. AVISO: Ajuste las ruedas calibradoras con el tractor en una superficie nivelada plana. 1.
OPERACIÓN PARA TRANSPORTAR (Vea Fig. 12) FUNCIONAMIENTO ATRÁS (ROS) Cuando empuje o arrastre su tractor asegúrese de desenganchar la transmisión poniendo el control de la rueda libre en la posición de marcha de rueda libre. El control de marcha de rueda libre esta situado debajo de asiento. • Levante la palanca de levantamiento del accesorio a su posición más alta.
OPERACIÓN AGREGUE GASOLINA TESTIGO DE BATERÍA/CONECTOR DE CARGA (Vea Fig. 13) • El testigo de la batería muestra el estado de la misma. Hay tres testigos distintos: 1. ROJO Se necesita carga 2. AMARILLO Se recomienda carga 3. VERDE No se necesita carga Llene el tanque de combustible hasta la parte inferior del cuello de relleno. No lo llene de más. Use gasolina normal nueva y limpia con un mínimo de 87 octanos. No mezcle aceite con gasolina.
OPERACIÓN PURGAR LA TRANSMISIÓN PARA HACER ARRANCAR EL MOTOR (Vea Fig. 3) Al hacer arrancar el motor por la primera vez o si se ha acabado el combustible del motor, se necesitará tiempo para el arranque extra para mover el combustible desde el estanque hasta el motor. • Asegúrese que el control de rueda libre este en la posición enganchada. • Siéntase en el sillón en la posición de operación, suelte el pedal del freno y ponga el freno de estacionamiento.
OPERACIÓN CONSEJOS PARA SEGAR • • • • • NO use cadenas de llanta cuando la carcasa de la cortadora de césped esté colocada en el tractor. La segadora debe estar nivelada en forma adecuada para obtener el mejor rendimiento al segar. Vea “PARA NIVELAR LA CAJA DE LA SEGADORA” en la sección de Servicio y Ajustes de este manual. El lado izquierdo de la segadora se debe usar para recorte. Maneje de modo que los recortes se descarguen en el área que ya ha sido cortada.
MANTENIMENTO PROGRAMA DE MANTENIMIENTO ANTES DE CADA USO CADA 8 HORAS CADA 25 HORAS CADA 50 HORAS CADA 100 HORAS CADA ALMACENAMIENTO TEMPORADA Revisar la operación del freno Revisar la presión de las llantas Verificar la sistemas presencia del operador y sistemas "ROS" T R A C T 0 R Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora 3 Tabla de lubricación Revisar el nivel de bateria 4 Limpiar la batería y los tereminales Limpie los residuos de la placa de dirección.
MANTENIMENTO TRACTOR PRECAUCIÓN: Usar solamente la hojas de repuesto aprobada por el fabricante de su cortacésped. Usar una hoja no aprobada por el fabricante de su cortacésped es peligroso, puede dañar su cortacésped y anular su garantía. Siempre observe las reglas de seguridad cuando dé mantenimiento.
MANTENIMENTO PARA CAMBIAR EL ACEITE DEL MOTOR (Vea Fig. 17 - 19) CORREAS "V" Revise las correas "V" para verificar si existe deterioro y desgaste después de 100 horas de operación y cámbielas si es necesario. Las correas no son ajustables. Cambie las correas si empiezan a deslizarse debido al desgaste. Determine la gama de la temperatura esperada antes de cambiar el aceite. Todo el aceite debe cumplir con la clasificación de servicio API SG-SL. • Asegúrese que el tractor esté en una superficie nivelada.
MANTENIMENTO FILTRO DE ACEITE DEL MOTOR SILENCIADOR Cambie el filtro de aceite del motor cada temporada o vez por medio que cambie el aceite, si el tractor se usa más de 100 horas en un año. NOTA: Si es necesario, retire las cubiertas de panel inferiores utilizando los pasos de la sección "Extracción de la cubierta del tablero inferior" de este manual. Inspeccione y cambie el silenciador corroído y el amortiguador de chispas (si viene equipado) pues pueden crear un peligro de incendio y/o daños.
MANTENIMENTO PUERTO DE LAVADO DE LA CUBIERTA (Vea Fig. 22) La plataforma del tractor está equipada con un puerto de lavado como parte del sistema de lavado de la plataforma. Se debe utilizar después de cada uso. 1. Lleve el tractor a un lugar horizontal y despejado de su césped, lo bastante cerca de una boca de riego como para que llegue la manguera del jardín. IMPORTANTE: Asegúrese de que la boca de descarga del tractor está orientada LEJOS de su casa, garaje, coches aparcados, etc.
SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal de freno completamente y aplique el freno de estacionamiento. • Ponga el embrague del accesorio en la posición desenganchado (DISENGAGED). • Ponga la llave de ignición en la posición de apagado (STOP) y remuévala. • Asegúrese que las cuchillas y que todas las partes movibles se hayan detenido completamente.
SERVICIO Y AJUSTES • • FIJE LOS BRAZOS DE SUSPENSIÓN LATERALES DE LA CORTADORA (A) AL CHASIS - Ubique el orificio del brazo encima de la clavija (B) que hay en la parte exterior del chasis del tractor, y fíjelo con una resorte de contención. Realice el mismo procedimiento en el otro lado del tractor. • Meta el fin de la conexión (E) en el hoyo en el suporte anterior de orificio y conecte con arandela e Retén del resorte (J). E A J F H B • FIG.
SERVICIO Y AJUSTES PARA NIVELAR LA SEGADORA AJUSTE DE DELANTE A ATRÁS (Vea Fig. 31 y 32) Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco inflados, el césped no le quedará bien cortado, lo cual podrá llevarlo a pensar que la Segadora no está bien regulada. IMPORTANTE: El piso debe quedar bien nivelado de lado a lado.
SERVICIO Y AJUSTES PARA CAMBIAR LA CORREA DE LA CUCHILLA DE LA SEGADORA (Vea Fig. 33) DESMONTAJE DE LA CORREA 1. Desmonte la segadora. (Ver “PARA DESMONTAR La segadora en este capítulo del manual.) NOTE: Observe toda la correa de impulsión de movimiento y la posición de todas las guías y guardacorreas. 2. Desconecte el arnés del cable del embrague (A). 3. Quite la pieza de unión anti-rotación (B) que está del lado derecho del tractor. 4.
SERVICIO Y AJUSTES IMPRESIÓN / INCLINACIÓN DE LAS RUEDAS DELANTERAS • La impresión e inclinación de las ruedas delanteras de su nuevo tractor vienen así de fábrica y son normales. La impresión y la inclinación de las ruedas delanteras no son regulables. En caso que se produzca algún daño que afecte la impresión o la inclinación de las ruedas delanteras tal como vinieron de fábrica, póngase en contacto con un centro de servicios u otro centro de servicios autorizado.
SERVICIO Y AJUSTES TRANSMISIÓN PARA CAMBIAR LA BOMBILLA DE LA LUZ DELANTERA • • • • REMOCIÓN/REEMPLAZO DE LA TRANSMISIÓN Levante el capota. Tire el sujetador de la bombilla fuera del agujero en la parte trasera del enrejado. Cambie la bombilla en el sujetador y empuje el sujetador de la bombilla, en forma segura, hacia atrás en el agujero en la parte trasera del enrejado. Cierre el capota.
ALMACENAMIENTO MOTOR Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más. SISTEMA DE COMBUSTIBLE Advertencia: Nunca almacene el tractor con gasolina en el estanque dentro de un edificio en donde los gases pueden alcanzar una llama expuesta o una chispa. Permita que el motor se enfríe antes de almacenarlo en cualquier recinto privado.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA No arranca CAUSA CORRECCIÓN 3. 4. 5. 6. 7. Sin combustible. Motor sin la “ESTRANGULACIÓN” (CHOKE) adecuada. Motor ahogado. Bujía mala. Filtro de aire sucio. Filtro de combustible sucio. Agua en el combustible. 3. 4. 5. 6. 7. 8. 9. Alambrado suelto o dañado. Válvulas del motor desajustadas. 8. 9. 1. 2. 3. 4. 5. Filtro de aire sucio. Bujía mala. Batería baja o descargada. Filtro de combustible sucio. Combustible rancio o sucio. 1. 2. 3. 4. 5. 6. 7.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA CAUSA El motor continúa funcionando cuando el operador se baja del asiento con el embrague del accesorio enganchado 1. El corte disparejo 1. 2. 3. Mala descarga del césped 1. Revise el alambrado, los interruptores y la conexiones.Si no están correctas, pongase en contacto con un centro de servicio cualificado. PRECAUCIÓN: NO opere la máquina sino hasta haber corregido el problema. Cuchilla desgastada, doblada o suelta. El conjunto segador no estánivelado.
Productos de consumo equipados con ruedas – Garantía limitada Husqvarna garantiza al comprador minorista original que este producto Husqvarna® carece de defectos materiales o de fabricación para un uso y mantenimiento normales desde el día de la compra, dentro del periodo de garantía aplicable indicado en el Anexo A. Esta Garantía limitada no se podrá transferir a ningún comprador posterior de este producto Husqvarna®.
(a) Abrasión en plataformas de cortadoras de césped. (b) Neumáticos dañados por pinchaduras externas. (c) Decoloración natural del material debido a la luz ultravioleta. (d) Daños en los equipos de corte por contacto con piedras u otros materiales y/o estructuras no admitidos.
Tabla de garantía limitada de 2013 para productos de consumo con ruedas Producto/Componente Tractores cortacésped: Bastidor, chasis, eje delantero Motor* Transmisión (si es fabricada por Husqvarna/Peerless) Transmisión (si es de terceros)** Solo modelos XLS - carcasa de plataforma moldeada. Garantía limitada del blindaje Carcasa de plataforma soldada.
Tabla de garantía limitada de 2013 para productos de consumo con ruedas Comercial (cualquier uso comercial, profesional, institucional, agrícola o que genere ingresos, que no sea para alquiler) 1 año 90 días Sin garantía Sin garantía Sin garantía Sin garantía Ver a la izquierda Consumidor Ver a la izquierda Comercial Ver a la izquierda Alquiler Producto/Componente Piezas y accesorios (si se compran) Accesorios (por ejemplo, trampa para césped, accesorios de protección para parachoques, etc.).
AVISO 66
GUÍA SUGERIDA PARA MEDIR LAS PENDIENTES CON LA VISTA PARA UNA OPERACIÓN SEGURA PL E G AR A LO EST L A RGO A ES DE U N L A A PEN LÍNE DIE A P N U T NTE E DE ADA 1 5 GRA DOS SOLAMENTE ANDE CUESTA ARRIBA O CUESTA ABAJO Y NO ATRAVIESE EL CERRO 15 GRADOS MAX. ADVERTENCIA: Para evitar daños graves, haga funcionar su tractor arriba y abajo de las pendientes, nunca transversalmente con respecto a las pendientes. No cortar pendientes mayores de 15 grados.
02/04/2013 CL/TH