Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. SLOPE OPERATION • • • • WARNING! When loading or unloading this machine, do not exceed the maximum recommended operation angle of 15°. • Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extreme caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Mow up and down slopes, not across.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 3 Gallons/11,35 L Regular Unleaded Oil Type: (API: SG-SL) SAE 10W30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: W/Filter: Spark Plug: Champion 24 132 03 (Gap: .030"/0,76 mm) CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance.
UNASSEMBLED PARTS Keys Slope Sheet Battery (1) Oil Drain Tube Key(s) (2) Hex Bolts (2) Nut Keps *Installed by Dealer (1) Quick Connect *Brush Guard Kit ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY • • • Lift seat pan or hood to raised position. Remove two terminal caps and discard. First connect RED battery cable to positive (+) terminal with bolt and nut as shown.
ASSEMBLY ✓CHECKLIST NOTE: You may now roll your tractor off the skid. Continue using the instructions that follow to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Ensure tractor is in a well-ventilated area. Ensure the area in front of tractor is clear of other people and objects.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Z P H E D G N B F A J C K L M Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute. (H) LIGHT SWITCH - Turns the headlights on and off.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping may cause engine to “backfire”.
OPERATION TO USE CRUISE CONTROL (J) (See Fig. 7) TO ADJUST GAUGE WHEELS (See Fig. 9) The cruise control feature can be used for forward travel only. Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE:Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height.
OPERATION REVERSE OPERATION SYSTEM (ROS) (See Fig. 11) TO TRANSPORT (See Fig. 3 and 12) When pushing or towing your tractor, ensure transmission is disengaged by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. • Raise attachment lift to highest position with attachment lift control. • Pull freewheel control out until the free wheel control rod locks in extended position. • Do not push or tow tractor at more than two (2) mph (3,2 km/h).
OPERATION TO START ENGINE (See Fig. 3) BEFORE STARTING THE ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Ensure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brake. • Move attachment clutch to “DISENGAGED” position.
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T R A C T O R Check Operator Presence and ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris off Steering Plate 5 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (mode
MAINTENANCE TRACTOR BATTERY Always observe safety rules when per form ing any maintenance. Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free.
MAINTENANCE BLADE CARE TO INSTALL BLADE • Clean area under top plate, the bottom of the mandrel assembly, and around bosses thoroughly to remove any dirt or debris. • Align bosses and insert blade. (See Fig. 18.) For best results mower blades must be kept sharp. Replace bent or damaged blades. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor, and void your warranty.
MAINTENANCE ENGINE OIL DRAIN VALVE LUBRICATION CLOSED AND LOCKED POSITION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. YELLOW CAP SAE VISCOSITY GRADES 10W30 5W-30 -20 F C -30 • 0 -20 30 -10 32 0 40 100 80 60 10 20 30 40 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE • Fig.
MAINTENANCE MUFFLER DECK WASHOUT PORT (See Fig. 26) Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. Your tractor’s deck is equipped with a washout port as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Ensure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig. 27) TO INSTALL MOWER (See Figs. 27 - 39) • • • 1.
SERVICE AND ADJUSTMENTS 2. ASSEMBLE FRONT GAUGE WHEEL (W) TO FRONT OF MOWER (See Fig. 30) H H. FRONT MOWER BRACKET W. FRONT GAUGE WHEEL X. SHOULDER BOLT Y. 1-1/4 O.D. WASHER Z. 3/8-16 LOCKNUT W X Z 5. INSTALL ANTI-SWAY BAR (S) (IF EQUIPPED) (See Fig. 33 - 35) Y ANTI-SWAY BAR (S) TOWARDS TRANSAXLE 90° END TOWARDS MOWER DECK INTEGRATED WASHER END Fig. 33 Fig. 30 3. TURN STEERING WHEEL LEFT AND POSITION MOWER (See Fig.
SERVICE AND ADJUSTMENTS • Insert other end of link (E) into hole in front mower bracket (H) and secure with washer and small retainer spring (J). NOTE: Requires deck lifting. 6. ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 36) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor. FRONT LINK LOCATION A M B D H F G A. MOWER SIDE SUSPENSION ARMS B.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • Ensure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly. FRONT-TO-BACK ADJUSTMENT (See Figs. 42 & 43) IMPORTANT: Deck must be level side-to-side. Recheck measurements, adjust if necessary until both sides are equal.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 44) TO REPLACE MOTION DRIVE BELT (See Fig. 45) MOWER DRIVE BELT REMOVAL • Park tractor on a level surface. Engage parking brake. • Lower attachment lift to its lowest position. • Disengage belt tension rod (K) from lock bracket (L). Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL 1. Remove mower.
SERVICE AND ADJUSTMENTS TO START ENGINE WITH A WEAK BATTERY (See Fig. 47) TO CHECK BRAKE If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1. Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake. 2. Disengage transmission by placing freewheel control in “transmission disengaged” position.
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 48) TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION 8. Loose or damaged wiring. 9. Engine valves out of adjustment. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8. Check all wiring. 9. Contact an authorized service center/department. Hard to start 1. 2. 3. 4. 5. 6. 7. Dirty air filter.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA L O NG D THIS O I T S T A E D LIN 1 5 DEG E RE E S LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles • • Mantener la máquina libre de hierba, hojas u otros escombros que pueden tocar el tubo de escape / partes del motor calientes y quemarse. No permitir que el puente del cortacésped cargue hojas u otros residuos que pueden causar acumulaciones. Limpiar toda salpicadura de aceite o carburante antes de hacer operaciones sobre la máquina o guardarla. Dejarla enfriar antes de guardarla. • • • • • III.
ESPECIFICACIONES DEL PRODUCTO Capacidad y Tipo de Gasolina: 11,35 L / 3 Galones Regular Sin Plomo Tipo de Aceite (API: SG-SL): SAE 10W30 (sobre 32°F/0°C) SAE 5W30 (deabajo 32°F/0°C) Capacidad de Aceite: Con Filtro: Sin Filtro: Bujía Champion 24 132 03 (Abertura: 0,76 mm /.030 ") Sistema de Carga: 12 Amps @3600 RPM Batería: Amp/Hr: Min. CCA: Modelo Tamaño: Torsión del Perno de la Cuchilla: FELICITACIONES por la compra de su tractor.
PEDAZOS PARA LA MONTAJE Batería Hoja de pendiente Llaves (2) Perno (1) Tubo de desagüe *Instalado por el distribuidor (1) Accesorio del conexión Llaves (2) Tuerca *Juego de cubierta MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío. HERRAMIENTAS NECESARIAS PARA EL MONTAJE • • Levante la base del asiento o capucha a una posición elevada.
MONTAJE ✓LISTA DE REVISIÓN AVISO: Ahora puede sacar el tractor de la tarima. Continúe usando las instrucciones que siguen para retirar el tractor de la tarima. ANTES DE OPERAR Y DE DISFRUTAR DE SU TRACTOR NUEVO, LE DESEAMOS QUE RECIBA EL MEJOR RENDIMIENTO Y LA MAYOR SATISFACCION DE ESTE PRODUCTO DE CALIDAD. ADVERTENCIA: Antes de empezar, leer, entender y seguir todas las instrucciones presentes en la sección Operaciones de este manual. Asegurarse que el tractor esté en un área bien ventilada.
OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL DE OPERARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. P H Z E D G N B F A J C K L M Fig. 3 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute. (H) INTERRUPTOR DE LA LUZ – Enciende y apaga las luces delanteras.
OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas. COMO USAR SU TRACTOR MOTOR • PARA AJUSTAR EL FRENO DE ESTACIONAMIENTO (Vea Fig.
OPERACIÓN UTILIZAR EL MANDO CRUCERO (Vea Fig. 7) • El césped promedio debe cortarse aproximadamente a 63,5 mm (2-1/2 pulgadas) durante la temporada fría y sobre 76,2 mm (3 pulgadas) durante los meses calurosos. Para obtener un césped más saludable y de mejor apariencia, siegue a menudo y después de un crecimiento moderado. • Para obtener el mejor rendimiento de corte, el césped que tiene más de 152,4 mm (6 pulgadas) de altura debe segarse dos veces.
OPERACIÓN PARA OPERAR EN CERROS PARA PARAR LAS CUCHILLAS DE LA SEGADORA • Desenganche el control del embrague del accesorio. ADVERTENCIA: No maneje hacia arriba o hacia abajo en cerros con pendientes superiores a 15° y no maneje atravesando ninguna pendiente. Utilice la guía de la pendiente proporcionada en la parte posteriora de este manual.
OPERACIÓN REMOLQUE DE CARRETILLAS O OTROS ACCESORIOS PRECAUCIÓN: Los combustibles mezclados con alcohol (llamados gasohol o que usan etanol o metanol) pueden atraer la humedad, lo que provoca la separación y formación de ácidos durante el almacenamiento. El gas ácido puede dañar el sistema de combustible de un motor mientras se encuentra en almacenamiento. Para evitar problemas con el motor, el sistema de combustible se debe vaciar antes del almacenamiento durante 30 días o más.
OPERACIÓN ARRANQUE CON TIEMPO FRÍO (50°F/10°C y menos) • Cuando arranque el motor, empuje lentamente el control de la estrangulación hacia adentro hasta que el motor empiece a funcionar suavemente. Siga empujándolo poco a poco permitiendo que el motor acepte pequeños cambios de velocidad y carga, hasta que este completamente hacia adentro. Si el motor empieza a funcionar mal, estire del control de la estrangulación un poco por unos cuantos segundos y continúe a empujar el control hacia adentro.
MANTENIMENTO PROGRAMA DE MANTENIMIENTO ANTES DE CADA USO CADA 8 HORAS CADA 25 HORAS CADA 50 HORAS CADA 100 HORAS CADA TEMPORADA ALMACENAMIENTO Revisar la operación del freno Revisar la presión de las llantas T R A C T O R Verificar la sistemas presencia del operador y sistemas "ROS" Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora 3 Tabla de lubricación Revisar el nivel de bateria 4 Limpiar la batería y los tereminales Limpie los residuos de la placa de dirección.
MANTENIMENTO TRACTOR BATERÍA Siempre observe las reglas de seguridad cuando dé mantenimiento. Su tractor cuenta con un sistema de carga de la batería que es suficiente para el uso normal. Sin embargo, si se carga la batería, periódicamente, con un cargador de automóviles se prolongará su duración. • Mantenga la batería y los terminales limpios. • Mantenga los pernos de la batería apretados. • Mantenga los agujeros de ventilación pequeños abiertos. • Vuelva a cargar a 6-10 amperes por 1 hora.
MANTENIMENTO CUIDADO DE LA CUCHILLA INTALACIÓN DE LA CUCHILLA • Limpie la zona debajo de la placa superior, la base del conjunto de mandril y alrededor de las pernos para eliminar cualquier resto de suciedad o desechos. • Alinee los pernos e inserte la cuchilla. (Vea la figura 18) Para obtener los mejores resultados, las cuchillas de la cortadora de césped deben estar afiladas. Reemplace las cuchillas dobladas o dañadas.
MANTENIMENTO MOTOR VÁLVULA DE DESAGÜE DEL ACEITE POSICIÓN CERRADA Y BLOQUEADA LUBRICACIÓN Use solamente aceite de detergente de alta calidad clasificado con la clasificación SG-SL de servicio API. Seleccione la calidad de viscosidad del aceite SAE según su temperatura de operación esperada. 3 46 02 CASQUILLO • Fig. 21 • Cambie el aceite después de 50 horas de operación o por lo menos una vez al año si el tractor se utiliza menos 50 horas el año.
MANTENIMENTO PUERTO DE LAVADO DE LA CUBIERTA (Vea Fig. 26) BUJÍA(S) Cambie las bujía(s) al comienzo de cada temporada de siega o después de cada 100 horas de operación, lo que suceda primero. El tipo de bujía y el ajuste de la abertura aparecen en “ESPECIFICACIONES DEL PRODUCTO” sección de este manual. La plataforma del tractor está equipada con un puerto de lavado como parte del sistema de lavado de la plataforma. Se debe utilizar después de cada uso. 1.
SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal del embrague/freno completamente y aplique el freno de estacionamiento. • Ponga el embrague del accesorio en la posición desenganchado (DISENGAGED). • Ponga la llave de ignición en la posición de apagado (STOP) y remuévala. • Asegúrese que las cuchillas y que todas las partes movibles se hayan detenido completamente.
SERVICIO Y AJUSTES 5. SI LA TIENE, INSTALE LA BARRA ANTIBALANCEO (S) (Vea Fig. 33 - 35) 2. ARME LA RUEDA CALIBRADORA DELANTERA (W) EN LA PARTE DELANTERA DE LA CORTADORA DE CÉSPED (Vea Fig. 30) H X Y Z BARRA ANTIBALANCEO (S) H. ESCUADRA DE LA CORTADORA DE CÉSPED DELANTERA W. RUEDA CALIBRADORA DELANTERA X. PERNO CON RESALTO Y. ARANDELA DE 1-1/4 Z. TUERCA DE SEGURIDAD DE 3/8-16 W HACIA EL TRANSEJE EXTREMO EN 90° HACIA LA PLATAFORMA DE LA CORTADORA DE CÉSPED EXTREMO CON ARANDELA INTEGRADA Fig.
SERVICIO Y AJUSTES 6. INSTALE LOS BRAZOS DE SUSPENSIÓN LATERAL DE LA CORTADORA DE CÉSPED (A) EN EL CHASIS (Vea Fig. 36) • Ubique el agujero delantero del brazo de suspensión lateral (A) sobre la chaveta en la parte exterior del chasis del tractor y asegure con una arandela grande y un resorte de retención grande (B). • Repita en el lado opuesto del tractor.
SERVICIO Y AJUSTES PARA NIVELAR LA SEGADORA AJUSTE DE DELANTE A ATRÁS (Vea Fig. 42 y 43) Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco inflados, el césped no le quedará bien cortado, lo cual podrá llevarlo a pensar que la segadora no está bien regulada. IMPORTANTE: El piso debe quedar bien nivelado de lado a lado.
SERVICIO Y AJUSTES PARA REEMPLAZAR LA CORREA DE LA CUCHILLA DE LA SEGADORA (See Fig. 44) DESMONTAJE DE LA CORREA 1. Desmonte la segadora. (Ver “PARA DESMONTAR La segadora en este capítulo del manual.) NOTE: Observe toda la correa de impulsión de movimiento y la posición de todas las guías y guardacorreas. 2. Desconecte el arnés del cable del embrague (A). 3. Quite la pieza de unión anti-rotación (B) que está del lado derecho del tractor. 4.
SERVICIO Y AJUSTES PARA HACER ARRANCAR EL MOTOR CON UNA BATERÍA BAJA (Vea Fig. 47) CONTROLAR Y AJUSTAR EL FRENO Si el tractor exige más de 1,5 m (cinco (5) pies) para pararse a una velocidad más alta en el cambio más alto en una superficie nivelada de hormigón seco o pavimentada, entonces se debe controlar y ajustar el freno. ADVERTENCIA: Las baterías de ácidoplo mo generan gases explosivos. Mantenga las chispas, las llamas y los materiales para fumar alejados de las baterías.
SERVICIO Y AJUSTES REEMPLAZAR LA BATERIA (Vea Fig. 48) PARA CAMBIAR EL FUSIBLE Cámbielo por un fusible tipo enchufable de 30 amps, tipo automotriz. El sujetador del fusible está ubicado detrás del tablero. ADVERTENCIA: No haga cortocircuito con los terminales de la batería al permitir que una llave de tuerca o cualquier otro objeto entre en contacto con ambos terminales a la misma vez. Antes de instalar la batería remueva las pulseras de metal, los relojes de pulsera de metal, los anillos, etc.
ALMACENAMIENTO MOTOR Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA No arranca CAUSA CORRECCIÓN 3. 4. 5. 6. 7. Sin combustible. Motor sin la “ESTRANGULACIÓN” (CHOKE) adecuada. Motor ahogado. Bujía mala. Filtro de aire sucio. Filtro de combustible sucio. Agua en el combustible. 3. 4. 5. 6. 7. 8. 9. Alambrado suelto o dañado. Válvulas del motor desajustadas. 8. 9. 1. 2. 3. 4. 5. Filtro de aire sucio. Bujía mala. Batería baja o descargada. Filtro de combustible sucio. Combustible rancio o sucio. 1. 2. 3. 4. 5. 6. 7.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA CAUSA El motor continúa funcionando cuando el operador se baja del asiento con el embrague del accesorio enganchado 1. El corte disparejo 1. 2. 3. Mala descarga del césped 1. Revise el alambrado, los interruptores y la conexiones.Si no están correctas, pongase en contacto con un centro de servicio cualificado. PRECAUCIÓN: NO opere la máquina sino hasta haber corregido el problema. Cuchilla desgastada, doblada o suelta. El conjunto segador no estánivelado.
GUÍA SUGERIDA PARA MEDIR LAS PENDIENTES CON LA VISTA PARA UNA OPERACIÓN SEGURA P L E G AR A LO EST L A RGO A ES DE U N L A A PEN LÍNE DIE A P N U T NTE E DE ADA 1 5 GRA DOS SOLAMENTE ANDE CUESTA ARRIBA O CUESTA ABAJO Y NO ATRAVIESE EL CERRO 15 GRADOS MAX. ADVERTENCIA: Para evitar daños graves, haga funcionar su tractor arriba y abajo de las pendientes, nunca transversalmente con respecto a las pendientes. No cortar pendientes mayores de 15 grados.
12/29/2015 TH