YTH150 TWIN Instruction manual Please read these instructions carefully and make sure you understand them before using this machine. Anleitungshandbuch Bitte lesen Sie diese Anleitungen sorgfältig durch und vergewissern Sie sich, daß Sie diese verstehen, bevor Sie die Maschine in Betrieb nehmen. Manuel d’instructions Merci de lire trés attentivement le manuel d'instructions. Assurez-vous d'avoir tout compris avant d'utiliser ce tracteur.
Safety rules. Sicherheitsvorschriften. Règles de sécurité. Reglas de seguridad. Norme antinfortunistiche. Veiligheidsregels. 2 Assembly. Zusammenbau. Montage. Montaje. Montaggio. Montering. 18 3 Functional description. Funktionsbeschreibung. Description du fonctionnement. Descripción del funcionamiento. Funzionamento. Beschrijving van functies. 25 4 Before starting. Maßnahmen vor dem Anlassen. Avant de démarrer. Antes del arranque. Prima dell’avviamento. Maatregelen vóór het starten.
1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. Training III. Operation • Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. • Never allow children or people unfamiliar with the instructions to use the lawnmower.
• • Stop the engine and disengage drive to attachment - before refueling; - before removing the grass catcher; - before making height adjustment unless adjustment can be made from the operator’s position. Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing. IV. Maintenance and Storage • • • • • • • • • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.
1. Sicherheitsvorschriften Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN. I. SCHULUNG • • • Die Anleitungen sorgfältig durchlesen. Mit den Bedienungselementen und der vorschriftsmäßigen Bedienung der Maschine vertraut machen.
• • • • • Vor dem Verlassen der Bedienungsstation: - Die Zapfwelle abstellen und alle Anbaugeräte absenken. - In Leerlauf schalten und die Feststellbremse einlegen. - Den Motor abstellen und den Zündschlüssel abziehen. Alle Anbaugeräte-Antriebe ausschalten, den Motor abstellen und das (die) Zündkerzenkabel abziehen bzw.
1. Règles de Sécurité Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS.L’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES. I. PRÉCAUTIONS D’UTILISATION • Lisez toutes les instructions soigneusement. Familiarisez vous avec les commandes pour appprendre à utiliser efficacement cette machine.
• • • • • Avant de quitter le siége : - débrayer les lames et abaisser le carter de coupe, - mettre le levier de vitesse au point mort et enclencher le frein de parking, - arrêter le moteur et retirer les clés, Débrayer les lames, arrêter le moteur, et débrancher le (s) fil (s) de (s) bougie (s) d’allumage ou retirer la clef de contact : - avant de retirer l’insert broyeur ou avant de retirer la goulotte d’éjection pour la nettoyer.
1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. I. INSTRUCCIÓN • Lea todas las instrucciones cuidadosamente.
• • • • • Antes de dejar la posición del operador: - desenganche la fuerza motriz y baje los accesorios; - cambie a neutro y enganche el freno de estacionamiento; - pare el motor y remueva la llave. Desenganche la transmisión a los accesorios, pare el motor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora; - después de golpear un objeto extraño.
1. Norme Antinfortunistiche Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. • I. ADDESTRAMENTO ALL’USO • Studiare attentamente le istruzioni. Acquisire dimestichezza con i comandi e conoscere a fondo l’uso corretto dell’equipaggiamento.
• • • • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele oppure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e prima di stasare lo scivolo; - prima di interventi o controlli sul tosaerba e prima delle operazioni di pulizia; - dopo aver colpito un oggetto estraneo.
1. Veiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. I. TRAINING • • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken.
YTH150TWIN • • • • Schakel de aandrijving naar de hulpstukken uit, stop de motor en maak de bougiekabel(s) los of verwijder het contactsleuteltje, - voordat u opgehoopt materiaal weghaalt of een verstopte afvoer leeg maakt; - voordat u de maaimachine controleert, schoonmaakt of eraan werkt; - nadat u een ongewenst voorwerp heeft geraakt.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
01738 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLETZUNGEN VERURSACHEN. ZU VERMEIDEN: • FUNKEN • FEUER • RAUCHEN SCHWEFELSÄURE KANN ERBLINDUNG ODER SCHWERE VERÄTZUNGEN VERURSACHEN. AUGEN UNVERZÜGLICH MIT WASSER AUSSPÜLEN. SOFORT ÄRZTLICHE HILFE AUFSUCHEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. GEEN • VONKEN • VUUR • ROKEN ZWAVELZUUR KAN BLINDHEID OF ERN-STIGE BRANDWONDEN VER-OORZAKEN. OGEN ONMIDDELLIJK MET WATER SPOELEN.
2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Before the tractor can be used certain parts must be assembled, which for transportation reasons are enclosed in the packing. Antes de poder utilizar el tractor, hay que montar algunas piezas que, por razones de transporte, van empaquetadas en el embalaje. Vor der Anwendung des Aufsitzmähers müssen gewisse Teile eingebaut werden, die aus Transportgründen in der Verpackung lose beigefügt sind.
2 ADJUST SEAT Lift up adjustment lever (A) and slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. Release lever to lock seat in position. EINSTELLEN DES SITZES A Heben Sie den Stellhebel (A) an und verschieben Sie den Sitz, bis eine bequeme Position erreicht ist, in der Sie Kupplungs- und Bremspedal ganz niederdrücken können. Lassen Sie den Hebel wieder in die Position zum Verriegeln des Sitzes einrasten.
2 01 4 23 PARA AJUSTAR LAS RUEDAS CALIBRADORAS TO ADJUST GAUGE WHEELS Las ruedas calibradoras están bien ajustadas cuando se encuentran un poco a distancia del terreno al mismo tiempo que la segadora esté a la altura de corte deseada. Entonces las ruedas calibradoras mantienen el conjunto segador en posición para prevenir el corte raspeo en casi todos los terrenos. • Ajuste las ruedas calibradoras con el tractor en una superficie nivelada plana.
3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies 14 2 1 5 11 3 7 8 6 4 9 Positioning of controls 1. Light Switch. 2. Throttle Control. 3. Brake Pedal. 4. Motion control lever. 5. Connection/disconnection of the cutting unit. 6. Quick lifting/lower of the cutting unit. 7. Ignition lock. 8. Parking Brake. 9. Free-wheel control lever. 11. Choke Control. 14.
3 14 2 1 5 11 3 7 8 6 4 9 Comandi Emplacement des commandes 1. 2. 3. 4. 5. 6. 7. 8. 9. 11. 14. 1. Interrupteur de commande des phares 2. Commande des gaz (Accélérateur) 3. Pédale d'embrayage et de frein 4. Levier de commande de la transmission hydrostatique 5. Embrayage/débrayage du carter de coupe. 6. Relevage et abaissement du carter de coup 7. Clé de contact/démarrage 8. Frein de parking. 9. Blocage/déblocage de la roue libre 11. Starter. 14. Rappel entetien/compteur horaire.
3 1. Light switch 1. Lichtschalter 1. Interrupteur des phares 47 3 01 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2. Gashebel 01355 Mit dem Gashebel wird die Drehzahl des Motors und damit die Drehgeschwindigkeit des Mähaggregats geregelt. = Vollgas = Leerlauf 2.
3 3. Brake Pedal Used for braking the tractor and starting the engine. 3. Bremspedal Wird zum Bremsen des Traktors und zum Starten des Motors benutzt. 3. Pédale de frein 3 47 02 Permet de freiner le tracteur et de démarrer le moteur. 01 35 8 3. Pedal del freno Se usa para frenar el tractor y arrancar el motor. 3. Pedale del freno Utilizzato per frenare il trattore e avviare il motore. 3. Rempedaal Gebruikt om de tractor te remmen en om de motor te starten.
3 4. Levier de commande de la transmission hydrostatique N Le levier peut être placé dans quatre positions différentes : N = Position neutre S = Vitesse lente F = Vitesse rapide R = Marche arrière Le levier peut être déplacé progressivement de S à F afin d'obtenir la vitesse désirée. R F 4.
3 5. Attachment clutch switch 5. Ein- und Ausschalten des Mähaggregats 5. Commande d'embrayage et de débrayage du carter de coupe 5. Acoplamiento y desacoplamiento de la unidad de corte 5. Leva inserimento tagliaerba. 5. Aan- en uitschakeling van de maaikast 6. Quick lifting/lowering of the cutting unit Pull the lever backwards to quickly lift the cutting unit when passing over irregularities in the lawn, etc. During transportation the cutting unit shall be in the highest position.
3 02927 OFF ROS ON ON 7. Ignition Lock There are three different positions for the ignition key: OFF All electric current broken. ROS ON Reverse Operation System (ROS) connected ON Electric current connected. START Start motor connected. Reverse Operation System (ROS) - Allows operation of mower deck or other powered attachment while in reverse (See section 5 - "Driving") WARNING! Never leave the key in the ignition lock when leaving the machine on its own. 7.
3 8. Freno de estacionamiento 8. Parking brake Aplique el freno de estacionamiento de la manera siguiente: 1. Apriete el pedal del freno hasta el fondo. 2. Tire de la palanca de freno hacia arriba y manténgala en esta posición. 3. Suelte el pedal. Para desaplicar el freno de estacionamiento sólo es necesario apretar el pedal del freno. Connect the parking brake in the following way: 1. Press down the brake pedal to bottom position. 2. Move the parking brake lever upwards and hold in this position. 3.
3 9. Blocage et déblocage de la roue libre Pour remorquer ou déplacer le tracteur sans l'aide du moteur, la commande de roue libre, qui se trouvesur le tablier arrière du châssis du tracteur, doit être tirée vers l'extérieur et bloquée dans cette position. 9. Acoplamiento y Desacoplamiento de Rueda Libre Para empujar o arrastrar su tractor sin la ayuda del motor, el botón de control de rueda libre debe ser tirado hacia afuera y puesto en su posición. 02219 9. Inserimento/Disinserimento Rouote 9.
3 14. Service Reminder/Hourmeter Indicates when service is required for the engine and mower. 14. Service Reminder/Studenzähler Zeigt an, wann der Motor und der Rasenmäher gewartet werden müssen. 14. Rappel Entetien/Compteur Horaire Indique à quel moment exécuter les opérations d’entretien du moteur et de la tondeuse . 03013 14. Recordatorio Mantenimiento/Cuenta-Horas Indica cuando es necesario realizar el mantenimiento para el motor y el cortacésped. 14.
4. Before starting. 4. Maßnahmen vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Filling up Reposición de combustible The engine should be run of pure (not oil mixed) unleaded petrol. Do not fill beyond the lower edge of the filling hole. Do not fill over max level. WARNING! Petrol is highly inflammable. Proceed with care and fill up with petrol outdoors. Do not smoke when filling with petrol or fill up when the engine is warm.
4 Le niveau atteint par l'huile doit se trouver entre les deux repères sur la jauge. Si ce n'est pas le cas, faire l'appoint avec de l'huile moteur SAE 30 jusqu'au repère "maxi" (FULL), jamais au dessus. En hiver, lorsque la température est inférieure à 0°, utilser de l'huile moteur SAE 5W30. 02473 02473 ADD FULL El nivel de aceite ha de estar entre las dos marcas de la varilla. Si no es este el caso, añadir aceite para motor SAE 30 hasta la marca de ”FULL” (lleno).
5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Starting of motor Make sure that the cutting unit is in the transport position and that the lever for connection/disconnection of the cutting unit is in the disconnection position. Anlassen des Motors Darauf achten, daß das Mähaggregat in Transportstellung steht und daß der Hebel für Ein- und Aus-schalten des Mähaggregats auf “ausgeschaltet” steht.
5 Pull out the choke control (if engine is cold). Den Kaltstarthebel herausziehen (nur bei kaltem Motor). Si le moteur est froid : Tirer la commande de starter. 3 36 01 Extraer el estrangulador (únicamente si el motor está frío). Estrarre il comando dello choke (in caso di partenza a freddo). Trek de choke uit (geldt alleen indien de motor koud is). Warm motor: Push the gas control half-way to full gass position " ". Bei warmem Motor: Gashebel in die Vollgasstellung " schieben.
5 Amener la clé de contact sur la position "Démarrage" ("START"). ATTENTION! Ne pas laisser tourner le démarreur plus de 5 secondes à chaque fois. Si le moteur ne démarre pas immédiatement, attendre une dizaine de secondes avant d'effectuer une nouvelle tentative. Ponga la llave de encendido en la posición de arranque ”START”. NOTA! No haga funcionar el motor de arranque más de unos 5 segundos a la vez. Si el motor no arranca, espere unos 10 segundos antes de hacer otra tentativa.
5 • IMPORTANT! COLD STARTING FOR HYDRO COLD STARTING FOR HYDRO (BELOW 40°F[4°C]) - AFTER STARTING ENGINE AND BEFORE DRIVING, LET TRANSMISSION WARM UP FOR ONE (1) MINUTE BY PLACING MOTION CONTROL LEVER IN NEUTRAL (N) POSITION AND RELEASING CLUTCH/BRAKE PEDAL. • • WICHTIG! KALTSTARTEN FÜR MASCHINEN MIT HYDROSTATISCHEM GETRIEBE FÜR TEMPERATUREN UNTERHALB VON 40° (4°C). NACH DEM ANLASSEN DES MOTORS DAS GETRIEBE (1) MINUTE LANG AUFWÄRMEN LASSEN, BEVOR LOSGEFAHREN WIRD. HIERZU DAS SCHALTGETRIEBE IN.
5 SPURGO DELLA TRASMISSIONE ATTENTION! Si LA TRANSMISSION A ETE DEPOSE POUR SON ENTRETIEN OU SON REMPLACEMENT, ELLE DEVRA ETRE PURGEE APRES SON REMONTAGE ET AVANT REUTILISATION DU TRACTEUR. • Placer le tracteur sur une surface plane afin qu'il ne puisse pas rouler dans aucune direction. Le frein de stationnement doit être desserré pour effectuer les opérations suivantes.
5 NOTE! NOTA! The machine is equipped with a safety switch which immediately breaks the current to the engine if the driver leaves the seat with engine running and with the connection/ disconnection lever in position “connection”. La máquina tiene un interruptor de seguridad que corta la corriente al motor si el conductor sale del asiento con el motor en marcha y con la palanca de acoplamiento/ desacoplamiento en la posición de acoplamiento.
5 ROS "ON" ROS "AN" ROS "ON" ROS "ON" ROS "ON" ROS "ON" 02828 Reverse Operation System (ROS) Engine "ON" (Normal Operating) Motor "AN" (Normalbetrieb) Moteur "ON" (Fonctionnement normal) Motor "ON" (Funcionamiento Normal) Motore "ON" (Funzionamento normale) Motor "ON" (normaal functioneren) Sécurité Marche Arrière (ROS) Your tractor is equipped with a Reverse Operation System (ROS).
5 Cutting tips Sistema Per Operazioni In Retromarcia (ROS) • Il Vostro trattore possiede un Reverse Operation System (ROS). Qualsiasi tentativo da parte dell’operatore di guidare nella direzione opposta con la frizione abbassata comporterà lo spegnimento del motore se la chiave di accensione non è inserita nel ROS nella posizione "ON". ATTENZIONE! Fare retromarcia con la frizione abbassata durante la guida è sconsigliato.
5 • • • • • • • • • • • • • • Conseils pour la tonte Retirer de la pelouse, les pierres et autres objets qui pourraient être propulsés par les lames et devenir ainsi des projectiles dangereux. Localiser et marquer les pierres et autres obstacles fixes afin d'éviter une éventuelle collision pendant la tonte. Commencer par couper assez haut, puis réduire progressivement cette hauteur de coupe jusqu'à obtention du résultat souhaité.
5 00272 Drive in right turns so that the cut grass is thrown away from flower beds and paths, etc. For larger lawns the drive direction should be changed after 2-3 turns so that the cut grass is thrown towards the area that has already been cut as shown in the illustration. In Rechtskurven fahren, damit das gemähte Gras von Beeten, Gängen usw. weggeschleudert wird.
5 Switching off the engine Move the attachment clutch control to disengaged position. Move the throttle control between half and full speed (fast) position. Lift up the cutting unit and turn the ignition key to “STOP” position. Abschalten des Motors Stellen Sie die Steuerung der Anhängerkupplung auf ausgekuppelt. Bewegen Sie die Gassteuerung auf die (fixe) Position zwischen halber und voller Geschwindigkeit. Heben Sie das Mähgerät hoch und drehen Sie den Zündschlüssel auf „STOP“-Position.
6. Maintenance, Adjustment. 6. Wartung (Instandhaltung), Einstellung. 6. Entretien, Réglages. 6. Mantenimiento, Ajuste. 6. Manutenzione. 6. Onderhoud, Afstelling. WARNING! ADVERTENCIA! Before servicing the engine or cutting unit the following shalll be carried out: • Press down the clutch/brake pedal and engage the parking brake lever. • Put gear lever in neutral. • Move connection/disconnection control to disengaged position. • Switch off engine. • Remove the ignition cable from the plug.
6 Motorhaube • • • 1 • • Motorhaube hochklappen. Scheinwerferanschluß lösen. Vor den Mäher treten. Motorhaube an den Seiten anfassen, nach vorn kippen und aus dem Mäher herausheben. Beim Wiedereinsetzen die Stützstreben der Motorhaube in die Schlitze des Rahmens schieben. Scheinwerferanschluß wieder anschließen und die Motorhaube schließen.
6 Maintenance Mantenimiento NOTE: Periodic maintenance should be performed on a regular basis in order to keep your tractor in good running condition. WARNING: Disconnect spark plug wire to prevent accidental starting before attempting any repair, inspection, or maintenance. Before each use: • Check oil, lubricate pivot points as necessary. • Check to see all bolts, nuts, and cotter pins are in place and secure. • Check the battery, terminals and vents. • Recharge slowly at 6 amperes if needed.
6 Pour assurer l'entretien du moteur Se référer au manuel d'utilisation du moteur. Vidange de l'huile du moteur Retirer le bouchon (1) et placer le tuyau de vidange (2). Pour ouvrir la soupape de vidange, repousser légèrement la soupape en la faisant tourner dans le sens contraire des aiguilles d'une montre pour sortir du cran, puis tirer sur la soupape pour libérer l'huile.
6 SERVICE RECORD Fill in dates as you complete regular service As Needed Every 8 hours Every 25 hours Change engine oil (without oil filter) ................................................... Every . 50 hours • Change engine oil (with oil filter) ............................................................................. Lubricate pivot points ......................................................................... Check brake operation ................................ • • Every .
6 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Selon les besoins Toutes les 8 H Toutes les 25 H Vidange de l'huile moteur Toutes les 50 H Toutes les 100 H Toutes les 200 H • (sans filtre à huile) .................................................................................... Vidange de l'huile moteur (avec filtre à huile) .........................................................................................................
6 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni 8 ore Ogni 25 ore Cambio dell'olio (Senza filtro dell’olio)................................................ Ogni.. 50 ore • Cambio dell'olio (Con filtro dell’olio) ........................................................................ Lubrificazione punti di articolazione ................................................... Controllo freni .............................................. • • Ogni..
6 Messerbalken Für beste Mähergebnisse müssen die Messerbalken immer opti mal geschliffen sein. Wechseln Sie verbogene oder beschädigte Messerbalken sofort aus. Sie werden mit einer Feile oder einer Schleifscheibe geschärft. HINWEIS: Um eine Unwucht zu vermeiden, müssen beide Seiten der Messerbalken gleichmäßig geschärft und auf Unwucht geprüft werden. WECHSELN DER MESSERBALKEN: Fahren Sie das Mähdeck in die höchste Position, um Zugriff zu den Messerbalken zu bekommen.
6 Lame Per avere il migliore risultato di taglio, è necessario che le lame siano ben affilate. Sostituirle se usurate o danneggiate. A tale scopo utilizzare una lima o una mola. NOTA! E’ importante affilare le due estremità della lama in modo uniforme per non creare disequilibri. RIMOZIONE DELLE LAME: Sollevare la macchina per avere accesso alle lame. Disserrare il bullone a testa esagonale, la rondella elastica e la rondella piatta che fissano la lama.
6 Operator Presence System and Reverse Operation System (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.
6 Sistema de Presencia Operador y Sistema de Funcionamiento Atrás (ROS) Asegurarse de que los sistemas de presencia operador y funcionamiento atrás funcionen adecuadamente. Si tu tractor no funciona como descrito, hay que reparar el problema inmediatamente. • El motor no tiene que arrancar hasta que le pedal del freno no esté completamente presionado, y el mando del embrague esté en la posición desembragada.
6 Controlar El Freno To Check Brake Si el tractor requiere más de cinco (5) pies para pararse a la velocidad más alta en la marcha más alta en una superficie nivelada seca en hormigón o adoquinada, hay que reparar el freno. If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1.
6 M F G R Q G A E B P K C L D To Remove Mower Entfernen Des Mähers • Place attachment clutch in “DISENGAGED” position. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L). CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and release slowly. • Remove mower belt from clutch pulley (M). • Dismantle the retainer spring (E) and remove the lever. • Dismantle the retainer spring (A) and remove the lever.
6 De Maaiunit Verwijderen Pour Démonter La Faucheuse • Zet de koppeling van het hulpstuk in de “ONTKOPPELDE” positie. • Zet de hendel van de hefinrichting in de laagste positie. • Ontkoppel de riemspanner (K) van de opsluitbeugel (L). WAARSCHUWING: De riemspanner heeft veerbelasting. Houd de stang goed vast en ontkoppel langzaam. • Verwijder de riem van de riemschijf van de koppeling (M). • Demonteer de haarpinveer (E) en verwijder de hefboom. • Demonteer de haarpinveer (A) en verwijder de hefboom.
6 Cambio de la correa propulsora del equipo de corte Replacement of drive belt for cutting unit 1. Desmontar el equipo de corte del tractor. 2. Quitar la polea izquierda de la unidad y después de las otras poleas. 3. Quitar después la correa de la unidad de corte. 4. Montar la nueva correa en el orden inverso. Controlar que la correa nueva se halla por dentro de todas la guías. 1. Dismantle the cutting unit as described previously. 2.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 To Level Mower 4. If adjustment is necessary, see step 2 in Visual Adjustment instructions above. 5. Recheck measurements, adjust if necessary until both sides are equal. Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Ausnivellieren des Mähers 5. Überprüfen Sie die Messungen noch einmal und stellen Sie die Stellmuttern nötigenfalls nach, bis beide Seiten gleich sind. Vergewissern Sie sich, dass die Reifen auf den Druck aufgeblasen sind, der auf den Reifen angegeben ist.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Pour mettre la tondeuse à niveau 5. Vérifiez à nouveau la distance et réglez-la au besoin jusqu’à ce que les deux côtés soient identiques. Vérifiez si les pneus sont correctement gonflés à la pression indiquée sur les pneus. Des pneus trop ou trop peu gonflés risquent de nuire à l’aspect de votre pelouse et de vous laisser croire que votre tondeuse est mal réglée.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Nivelar el cortacésped AJUSTE DE LA PARTE DELANTERA A LA TRASERA IMPORTANTE: la cubierta ha de ser nivelada de un lado al otro. Para obtener los mejores resultados de corte, las hojas del cortacésped han de ajustarse de modo que la punta frontal sea entre 1/8" y 1/2" más bajo que la punta trasera cuando la cortacésped está en su posición más alta. PRECAUCIÓN: Las hojas cortan.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Livellamento del rasaerba 5. Verificare nuovamente le misurazioni, regolare secondo necessità finché entrambi i lati siano pari. Verificare che i pneumatici siano adeguatamente gonfati in base ai psi riportati sugli stessi.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 De maaiunit nivelleren 5. Controleer de metingen opnieuw, en stel de messen af totdat beide zijden gelijk zijn. Zorg ervoor dat de banden tot de PSI-waarde die op de banden zelf staat aangegeven zijn opgepompt. Als de banden te hard of te zacht zijn, kan dat het uiterlijk van uw grasveld beïnvloeden zodat u denkt dat de maaiunit niet goed is afgesteld.
6 4. Install belt on centerspan idler (E). 5. Install belt through stationary idler (C) and clutching idler (D). 6. Reinstall anti-rotation link (B) on right side of tractor. Tighten securely. 7. Reconnect clutch harness (A). 8. Make sure belt is in all pulley grooves and inside all belt guides and keepers. 9. Install mower (See “ASSEMBLY OF THE CUTTING UNIT” in this section of manual). G H B Austauschen Des Motorantriebsriemens Parken Sie den Traktor auf einer ebenen Fläche.
6 3. Tirez la courroie vers l’arrière du tracteur. Faites passer prudemment la courroie autour du ventilateur de refroidissement de la transmission et autour de la poulie de puissance (F). Vérifiez si la courroie se trouve dans le passant de la courroie. 4. Montez la courroie sur la poulie folle médiane (E) 5. Faites passer la courroie à travers la poulie folle stationnaire (C) et la poulie folle de l’embrayage (D). 6. Remontez la connexion anti-rotation (B) sur le côté droit du tracteur. Serrez solidement.
6 4. 5. 6. G 7. 8. H B 9. Posizionare con cautela la cinghia attorno alla ventola di raffreddamento della trasmissione e sulla puleggia di ingresso (f). Verificare che la cinghia si trovi all’interno del relativo fermo. Installare la cinghia sul pignone folle della sezione centrale (e). Inserire la cinghia attraverso il pignone folle fisso (C) e il pignone d’innesto (D). Reinstallare l'articolazione anti-rotazione (B) sul lato destro del trattore. Serrare saldamente.
6 EINSTELLUNG DES STEUERKNÜPPELS DES SCHALTGETRIEBES Der Steuerknüppel wird von der Herstellerfirma im Werk voreingestellt und erfordert daher in der Regel keine weiteren Einstellungen.
6 1 02239 3 REGOLAZIONE DELLA LEVA DI COMANDO DEL MOVIMENTO DEL MECCANISMO DEL CAMBIO La leva di comando del movimento del meccanismo del cambio è stata impostata al momento della fabbricazione e non richiede pertanto ulteriori regolazioni.
6 ENFRIAMIENTO DEL TRANSEJE TRANSAXLE COOLING Las aletas de enfriamiento y el ventilador de la transmisión tienen que mantenerse limpios para asegurar el enfriamiento adecuado. No trate de limpiar el ventilador o la transmisión cuando el motor esté funcionando o mientras la transmisión esté caliente. • Inspeccione el ventilador de enfriamiento para asegurarse que las aspas del ventilador estén intactas y limpias.
7. Troubleshooting 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Motor springt nicht an 1. Kraftstoff fehlt im Kraftstofftank. 2. Defekte Zündkerze. 3. Defekter Zündkerzenanschluß. 4. Schmutz in Vergaser oder Kraftstoffleitung. Start motor will not turn engine 1. Battery flat. 2. Poor contact between cable and battery pole. 3. Connection/disconnection level in wrong position. 4. Main fuse defective. 5.
7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne démarre pas 1. Manque de carburant dans le réservoir. 2. Bougie d'allumage défectueuse. 3. Le câblage de la bougie d'allumage défectueux. 4. Il y a des impuretés dans le carburateur ou dans le circuit du carburant. El motor no arranca 1. No hay combustible en el depósito. 2. La bujía es errónea. 3. La conexión de la bujía está defectuosa. 4. Hay suciedad en el carburador o en el tubo de combustible. Le démarreur n'entraîne pas le moteur 1.
7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. De motor start niet 1. Er is geen benzine in de tank. 2. De bougie is defect. 3. De bougie-aansluiting is defect. 4. Vuil in carburateur of brandstofleiding. Il motorino di avviamento non fa girare il motore 1. Batteria scarica. 2. Difetto di contatto tra cavo e polo della batteria. 3.
8. Storage. 8. Aufbewahrung. 8. Remisage. 8. Conservación. Suivre la procédure suivante une fois la saison terminée: • En fin de saison, suivre la procédure suivante pour le remisage. N’utilisez pas de nettoyeur haute pression pour le lavage. L’eau pourrait s’infiltrer dans le moteur et abréger ainsi la durée de l’appareil. • Nettoyer l'ensemble de la machine et plus particulièrement l'intérieur du carter de coupe.
8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti interventi: • Pulire tutto il tagliaerba e particolarmente sotto il coperchio della falciatrice. Per le operazioni di pulizia, non utilizzare acqua ad alta pressione. L’acqua può infiltrarsi nel motore e nel sistema di trasmissione, riducendo quindi così il tempo di vita della macchina. • Ritoccare danni alla verniciatura per evitare ossidazione. • Cambiare l’olio del motore. • Vuotare il serbatoio della benzina.
532 41 62-99 Rev. 1 10.27.08 CL Printed in the U.S.A.