07002 YTH183T Instruction manual Manuel d’instructions Manuale di istruzioni Please read these instructions carefully and make sure you understand them before using this machine. Merci de lire trés attentivement le manuel d'instructions. Assurez-vous d'avoir tout compris avant d'utiliser ce tracteur. Prima di utilizzare la macchina leggete queste istruzioni con attenzione ed accertatevi di averle comprese bene.
1 Safety rules. Sicherheitsvorschriften. Règles de sécurité. Montaje. Montaggio. Montering. 2 Assembly. Zusammenbau. Montage. Descripción del funcionamiento. Funzionamento. Beschrijving van functies. 18 3 Functional description. Funktionsbeschreibung. Description du fonctionnement. Antes del arranque. Prima dell’avviamento. Maatregelen vóór het starten. 20 4 Before starting. Maßnahmen vor dem Anlassen. Avant de démarrer. Conducción. Guida. Rijden. 30 5 Driving. Betrieb. Conduite.
1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. TRAINING III. OPERATION • Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. • Never allow children or people unfamiliar with the instructions to use the lawnmower.
IV. MAINTENANCE AND STORAGE • • • • • • • • • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. Never store the equipment with petrol in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. To reduce the fire hazard, keep the engine, silencer, battery compartment and petrol storage area free of grass, leaves, or excessive grease.
1. Sicherheitsvorschriften Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN. • I. SCHULUNG • Die Anleitungen sorgfältig durchlesen. Mit den Bedienungselementen und der vorschriftsmäßigen Bedienung der Maschine vertraut machen.
• • • • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstellen und das (die) Zündkerzenkabel abziehen bzw. den Zündschlüssel abziehen: - vor dem Entfernen von Verstopfungen aus dem Mähwerk oder dem Auswurf; - vor dem Prüfen, Reinigen oder Reparieren des Rasenmähers; - nachdem auf ein Fremdkörper gestoßen wurde.
1. Règles de Sécurité Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS.L’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES. • • I. PRÉCAUTIONS D’UTILISATION • Lisez toutes les instructions soigneusement. Familiarisez vous avec les commandes pour appprendre à utiliser efficacement cette machine.
• • • • Débrayer les lames, arrêter le moteur, et débrancher le (s) fil (s) de (s) bougie (s) d’allumage ou retirer la clef de contact : - avant de retirer l’insert broyeur ou avant de retirer la goulotte d’éjection pour la nettoyer. - avant de contrôler, nettoyer ou travailler sur le carter de coupe, - avant de retirer un objet coincé dans le tracteur de pelouse.
1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. • I. INSTRUCCIÓN • Lea todas las instrucciones cuidadosamente.
• • • • Desenganche la transmisión a los accesorios, pare el motor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora; - después de golpear un objeto extraño.
1. Norme Antinfortunistiche Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. • I. ADDESTRAMENTO ALL’USO • Studiare attentamente le istruzioni. Acquisire dimestichezza con i comandi e conoscere a fondo l’uso corretto dell’equipaggiamento.
- • • • prima di pulire eventuali intasamenti e prima di stasare lo scivolo; - prima di interventi o controlli sul tosaerba e prima delle operazioni di pulizia; - dopo aver colpito un oggetto estraneo. Controllare che il tosaerba non sia stato danneggiato ed effettuare le riparazioni del caso prima di riavviare e mettere in funzione l’equipaggiamento; - se il tosaerba, o trattorino, vibra in modo anomalo (in qual caso eseguire immediatamente dei controlli).
1. Veiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. I. TRAINING III. BEDIENING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken.
YTH183T • • • Schakel de aandrijving naar de hulpstukken uit tijdens transport of als ze niet worden gebruikt. Stop de motor en schakel de aandrijving naar het hulpstuk uit, - voordat u tankt; - voordat u de opvangzak verwijdert; - voordat u de hoogte verstelt tenzij de hoogte vanuit de bestuurdersplaats kan worden ingesteld. Minder gas tijdens het uitlopen van de motor, en als de motor met een afsluitklep is uitgerust, moet u de brandstoftoevoer aan het einde van het maaien afsluiten. 13.41/10.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
01738 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLETZUNGEN VERURSACHEN. ZU VERMEIDEN: • FUNKEN • FEUER • RAUCHEN SCHWEFELSÄURE GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN GEEN • VONKEN • VUUR • ROKEN ZWAVELZUUR NO • CHISPAS • LLAMAS • FUMAR ÁCIDO SULFÚRICO DIVIETO • SCINTILLE • FIAMME • SIGARETTE ACIDO SOLFORICO KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. PELIGRO PROTEJE SUS OJOS GASES EXPLOSIVOS PUEDEN CAUSAR CEGUE-DAD O LESIONES.
2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. 02 REMARQUE: Si la batterie est mise en service au-delà de l'année et du mois indiqués sur l'étiquette, recharger la batterie, pendant une heure au moins, à 6-10 A. ATTENTION: Avant de mettre en place la batterie, prendre la précaution de retirer gourmette, montre-bracelet, anneau, etc. Leur contact avec la batterie pouvant entraîner des brûlures.
2 ADJUST SEAT Lift up adjustment lever (A) and slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. Release lever to lock seat in position. EINSTELLEN DES SITZES Heben Sie den Stellhebel (A) an und verschieben Sie den Sitz, bis eine bequeme Position erreicht ist, in der Sie Kupplungs- und Bremspedal ganz niederdrücken können. Lassen Sie den Hebel wieder in die Position zum Verriegeln des Sitzes einrasten.
3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies 1 5 14 2 7 3 11 6 8 12 4 9 Positioning of controls 1. 2. 3. 4. 5. 6. 7. 8. 9. 11. 12. 14. Anordnung der Bedienungseinrichtungen Light switch Throttle control Brake and clutch pedal Forward/Reverse Drive Pedal.
3 1 5 14 2 7 3 11 6 8 12 4 9 Emplacement des commandes Comandi 1. 2. 3. 4. 5. 6. 7. 8. 9. 11. 12. Interrupteur des phares (si équipé) Commande de gaz Pédale de frein et d'embrayage Pédale de marche avant/marche arrière Embrayage/débrayage du groupe de coupe Abaissement et relevage du plate au de coupe. Serrure de contact Frein de parking. Blocage/déblocage de la roue libre Starter Levier de commande de la vitesse de croisière (Cruise control) 14. Rappel Entetien/Compteur Horaire 1. 2. 3. 4. 5.
3 1. Light switch 1. Lichtschalter 7 34 01 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2. Gashebel Mit dem Gashebel wird die Drehzahl des Motors und damit die Drehgeschwindigkeit des Mähaggregats geregelt. = Vollgas = Leerlauf 01355 2.
3 3. Brake Pedal Used for braking the tractor and starting the engine. 3. Bremspedal 3 Wird zum Bremsen des Traktors und zum Starten des Motors benutzt. 3. Pédale de frein Permet de freiner le tracteur et de démarrer le moteur. 3. Pedal del freno Se usa para frenar el tractor y arrancar el motor. 3. Pedale del freno Utilizzato per frenare il trattore e avviare il motore. 3. Rempedaal Gebruikt om de tractor te remmen en om de motor te starten. 4.
3 5. Attachment clutch switch 5. Ein und Ausschalten des Mähaggregats 5. Commande d'embrayage et de débrayage du carter de coupe 5. Acoplamiento y desacoplamiento de la unidad de corte 5. Leva inserimento tagliaerba 5. Aan en uitschakeling van de maaikast 6. Relevage et abaissement du carter de coupe Tirer sur le levier vers l'arrière pour relever rapidement le carter de coupe lors du passage sur une surface accidentée.
3 OFF ROS ON ON 7. Ignition Lock START 7. Cerradura de encendido There are four different positions for the ignition key: OFF All electric current broken. Reverse Operation System (ROS) connected ROS ON ON Electric current connected. START Start motor connected. Reverse Operation System (ROS) - Allows operation of mower deck or other powered attachment while in reverse (See section 5 - "Driving").
3 8. Parking brake 8. Freno de estacionamiento Connect the parking brake in the following way: 1. Press down the brake pedal to bottom position. 2. Move the parking brake lever upwards and hold in this position. 3. Release the brake pedal. To release the parking brake all that is necessary is to push down the brake pedal. Aplique el freno de estacionamiento de la manera siguiente: 1. Apriete el pedal del freno hasta el fondo. 2. Tire de la palanca de freno hacia arriba y manténgala en esta posición. 3.
3 9. Blocage et déblocage de la roue libre Pour remorquer ou déplacer le tracteur sans l'aide du moteur, la commande de roue libre, qui se trouvesur le tablier arrière du châssis du tracteur, doit être tirée vers l'extérieur et bloquée dans cette position. 9. Acoplamiento y Desacoplamiento de Rueda Libre 02203 Para empujar o arrastrar su tractor sin la ayuda del motor, el botón de control de rueda libre debe ser tirado hacia afuera y puesto en su posición. 9. Free-wheel Control Lever 9.
3 12. Palanca de mando crucero La característica de mando crucero se puede usar solo para ir hacia adelante. CARACTERÍSTICAS DEL SISTEMA El mando crucero tiene que usarse solo mientras se corta o transporta en un superficies relativamente lisa y recta. Otras condiciones como podar a velocidad reducida puede causar el desembrague del mando crucero. No usar el mando crucero en vertientes, terrenos ásperos o mientras se poda o se gira.
3 14. Service Reminder/Hourmeter Indicates when service is required for the engine and mower. 14. Service Reminder/Studenzähler Zeigt an, wann der Motor und der Rasenmäher gewartet werden müssen. 14. Rappel Entetien/Compteur Horaire Indique à quel moment exécuter les opérations d’entretien du moteur et de la tondeuse. 03013 14. Recordatorio Mantenimiento/Cuenta-Horas Indica cuando es necesario realizar el mantenimiento para el motor y el cortacésped. 14.
4. Before starting. 4. Maßnahmen vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Reposición de combustible Filling up The engine should be run of pure (not oil mixed) unleaded petrol. Do not fill beyond the lower edge of the filling hole. Do not fill over max level. El motor ha de funcionar con gasolina pura (sin mezcia de aceite), sin plomo. El nivel no ha de sobrepasar el borde inferior del orificio de llenado.
4 Oil level Nivel de aceite The combined oil refilling cap and the oil stick is accessible when the bonnet is lifted forwards. The oil level in the engine should be checked before each run. Make sure that the tractor is horizontal. Unscrew the oil stick and wipe clean. Replace the oil stick and screw tight. Remove again and check the level. La tapa combinada para el llenado de aceite y para la varilla de nivel queda accesible después de haber levantado hacia adelante el capó del motor.
5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Starting of motor Sit on seat in operating position, depress brake pedal and set parking brake. Make sure that the cutting unit is in the transport position (top position) and that the attachment clutch control for connection/disconnection of the cutting unit is in the disconnection position. Anlassen des Motors Setzen Sie sich in Betriebsposition auf den Sitz, drücken Sie das Bremspedal und stellen Sie die Feststellbremse ein.
5 Bei warmem Motor: Gashebel in die Vollgasstellung " schieben. " Si le moteur est chaud: pousser la commande des gaz à mi-distance de sa position d'accélération maximale" ". Moter caliente: Empuje el acelerador hasta la mitad de su recorrido hacia la posición de plenos gases " ". Motore caldo: Portare il comando del gas sul massimo " ". Bij een warme motor: Schuif de gashendel halverwege naar de volgaspositie " ". Warm motor: Push the gas control half-way to full gas position " ".
5 PURGE TRANSMISSION PURGE DE LA TRANSMISSION To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor. Pour assurer un fonctionnement et un rendement corrects, il est recommandé de purger la transmission avant d'utiliser le tracteur pour la première fois.
5 • PURGAR LA TRANSMISIÓN Para asegurar la operación y ejecución adecuada, es recomendado que la transmisión sea purgada antes de operar el tractor para la primera vez. Este proceso removerá cualquier aire adentro de la transmisión que se halla formado durante el transporte de su tractor. IMPORTANTE: SI POR ACASO SU TRANSMISIÓN DEBE SER REMOVIDA PARA SERVICIO O REEMPLAZO, DEBE SER PURGADA DESPUÉS DE LA REINSTALACION Y ANTES DE OPERAR EL TRACTOR.
5 NOTE! NOTA! The machine is equipped with a safety switch which immediately breaks the current to the engine if the driver leaves the seat with engine running and with the connection/ disconnection control in position “connection”. La máquina tiene un interruptor de seguridad que corta la corriente al motor si el conductor sale del asiento con el motor en marcha y con la palanca de acoplamiento/ desacoplamiento en la posición de acoplamiento.
5 Per avanzare e retrocedere La direzione e la velocità di movimento sono controllate azionando i pedali di avanzamento e di retromarcia. • Avviare il trattore e rilasciare il freno di stazionamento. • Premere lentamente il pedale di avanzamento o di retromarcia per avviare il movimento. La velocità al suolo aumenta ma mano che si preme il pedale. Pour avancer et pour reculer La direction et la vitesse du déplacement sont contrôlées par les pédales de marche avant et de marche arrière.
5 ROS "ON" ROS "AN" ROS "ON" ROS "ON" ROS "ON" ROS "ON" 02828 Reverse Operation System (ROS) Engine "ON" (Normal Operating) Motor "AN" (Normalbetrieb) Moteur "ON" (Fonctionnement normal) Motor "ON" (Funcionamiento Normal) Motore "ON" (Funzionamento normale) Motor "ON" (normaal functioneren) Sécurité Marche Arrière (ROS) Your tractor is equipped with a Reverse Operation System (ROS).
5 Cutting tips Sistema per operazioni in retromarcia (ROS) • Il Vostro trattore possiede un Sistema per operazioni in retromarcia (ROS). Qualsiasi tentativo da parte dell’operatore di guidare nella direzione opposta con la frizione abbassata comporterà lo spegnimento del motore se la chiave di accensione non è inserita nel ROS nella posizione "ON". ATTENZIONE! Fare retromarcia con la frizione abbassata durante la guida è sconsigliato.
5 Conseils pour la tonte • • • • • • • Consigli per il taglio dell’erba • • • Retirer de la pelouse, les pierres et autres objets qui pourraient être propulsés par les lames et devenir ainsi des projectiles dangereux. Localiser et marquer les pierres et autres obstacles fixes afin d'éviter une éventuelle collision pendant la tonte. Commencer par couper assez haut, puis réduire progressivement cette hauteur de coupe jusqu'à obtention du résultat souhaité.
5 ATTENTION! • • • Ne jamais utiliser un tracteur sur des pentes excédant 15°. Les risques de renversement étant alors très importants. Ne jamais rouler parallèlement à la pente du fait des risques de renversement. Toujours rouler perpendiculairement à la pente, aussi bien en montant, qu'en descendant. Ne jamais arrêter ou démarrer un tracteur en pente. ADVERTENCIA! • • • WARNING! • • • Do not drive in terrain at an angle of more than max. 15°. The risk for roll-over backwards is large.
5 Switching off the engine Move the attachment clutch control to disengaged position. Move the throttle control between half and full speed (fast) position. Lift up the cutting unit and turn the ignition key to “STOP” position. Abschalten des Motors Stellen Sie die Steuerung der Anhängerkupplung auf ausgekuppelt. Bewegen Sie die Gassteuerung auf die (fixe) Position zwischen halber und voller Geschwindigkeit. Heben Sie das Mähgerät hoch und drehen Sie den Zündschlüssel auf „STOPP“-Position.
6. Maintenance, adjustment. 6. Wartung (Instandhaltung), Einstellung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! ADVERTENCIA! Before servicing the engine or cutting unit the following shall be carried out: • Press down the clutch/brake pedal and engage the parking brake lever. • Move connection/disconnection control to disengaged position. • Switch off engine. • Remove the ignition cable from the plug.
6 Engine hood • • • 1 • • Raise hood. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt forward and lift off of tractor. To reinstall, slide hood pivot brackets into slots in frame. Reconnect headlight wire connector and close hood. Motorhaube • • • 07002 • • Motorhaube hochklappen. Scheinwerferanschluß lösen. Vor den Mäher treten. Motorhaube an den Seiten anfassen, nach vorn kippen und aus dem Mäher herausheben.
6 Reinigung Verwenden Sie für die Reinigung keine Hochdruckreinigungsgeräte. Das Wasser könnte in den Motor oder das Getriebe eindringen und die Lebensdauer der Maschine verkürzen. Reinigen Der Lenkungsplatte: • Entfernen Sie Verunreinigungen von der Lenkungsplatte. Verunreinigungen können die Kupplungs-/Bremspedalwelle in ihrer Beweglichkeit behindern, so dass der Riemen durchrutscht und die Antriebskraft verloren geht. 5 4 2 WARNUNG: Vermeiden Sie alle Quetschkanten und beweglichen Teile. 1 1.
6 • Tenere il trattore pulito per evitare surriscaldamento del motore e danni conseguenti. • Controllare il funzionamento del freno. Pulizia Per le operazioni di pulizia, non utilizzare acqua ad alta pressione. L’acqua può infiltrarsi nel motore e nel sistema di trasmissione, riducendo quindi così il tempo di vita della macchina. Pulizia Della Piastra Sterzo: • Pulire la piastra sterzo da eventuali detriti.
6 ÖLWECHSEL DURCHFÜHREN Entfernen der linken unteren Abdeckung des Armaturenbretts • Den Deckel anheben. VORSICHT: Die untere Abdeckung des Armaturenbretts (1) vorsichtig abnehmen, die Laschen der Abdeckung (2) sind zerbrechlich. • Die Abdeckung (1) nach oben ziehen, bis die Kegelschlitze im unteren Armaturenbrett die Laschen der Abdeckung (2) freigeben, und entfernen. 1 2 Ventil für den Ölablauf • Das Abflussrohr am Ventil montieren.
6 PER CAMBIARE L’OLIO Rimozione copertura cruscotto inferiore sinistro • Sollevare il cofano. ATTENZIONE: Prestare attenzione nel togliere la copertura cruscotto inferiore (1) per non rompere le alette della copertura (2). • Togliere la copertura cruscotto inferiore (1) facendola scorrere verso l’alto fino a sganciare le alette della copertura (2) dalle apposite guide (3). Valvola di scarico dell’olio 1 • • • 2 • 3 Montare il tubo di scarico sulla valvola.
6 SERVICE RECORD Fill in dates as you complete regular service As Needed Every 8 hours Every 25 hours Change engine oil (without oil filter) ................................................... Every . 50 hours • Change engine oil (with oil filter) ............................................................................. Lubricate pivot points ......................................................................... Check brake operation ................................ • • Every .
6 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Selon les besoins Toutes les 8 H Toutes les 25 H Vidange de l'huile moteur Toutes les 50 H Toutes les 100 H Toutes les 200 H • (sans filtre à huile) .................................................................................... Vidange de l'huile moteur (avec filtre à huile) .........................................................................................................
6 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni 8 ore Ogni 25 ore Cambio dell'olio (Senza filtro dell’olio)................................................ Ogni . 50 ore • Cambio dell'olio (Con filtro dell’olio) ........................................................................ Lubrificazione punti di articolazione ................................................... Controllo freni ..............................................
6 Operator Presence System and Reverse Operation System (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.
6 Sistema de Presencia Operador y Sistema de Funcionamiento Atrás (ROS) Asegurarse de que los sistemas de presencia operador y funcionamiento atrás funcionen adecuadamente. Si tu tractor no funciona como descrito, hay que reparar el problema inmediatamente. • El motor no tiene que arrancar hasta que le pedal del freno no esté completamente presionado, y el mando del embrague esté en la posición desembragada.
6 Messerbalken 02 Für beste Mähergebnisse müssen die Messerbalken immer opti mal geschliffen sein. Wechseln Sie verbogene oder beschädigte Messerbalken sofort aus. Sie werden mit einer Feile oder einer Schleifscheibe geschärft. HINWEIS: Um eine Unwucht zu vermeiden, müssen beide Seiten der Messerbalken gleichmäßig geschärft und auf Unwucht geprüft werden. WECHSELN DER MESSERBALKEN: • Fahren Sie das Mähdeck in die höchste Position, um Zugriff zu den Messerbalken zu bekommen.
6 Lame 02 Per avere il migliore risultato di taglio, è necessario che le lame siano ben affilate. Sostituirle se usurate o danneggiate. A tale scopo utilizzare una lima o una mola. NOTA: E’ importante affilare le due estremità della lama in modo uniforme per non creare disequilibri. RIMOZIONE DELLE LAME: • Sollevare la macchina per avere accesso alle lame. • Rimuovere il bullone dalla lama. • Montare una nuova lama o una lama con palettaura posteriore rivolta verso il piatto, come indicato.
6 M A E A D To Remove Mower Entfernen Des Mähers • Place attachment clutch in “DISENGAGED” position. • Lower attachment lift lever to its lowest position. CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and release slowly. • Remove mower belt from clutch pulley (M). • Dismantle the retainer spring (E) and remove the lever. • Dismantle the retainer spring (A) and remove the lever. • Dismantle the retainer spring (D) and remove the lever.
6 De Maaiunit Verwijderen Pour Démonter La Faucheuse • Zet de koppeling van het hulpstuk in de “ONTKOPPELDE” positie. • Zet de hendel van de hefinrichting in de laagste positie. WAARSCHUWING: De riemspanner heeft veerbelasting. Houd de stang goed vast en ontkoppel langzaam. • Verwijder de riem van de riemschijf van de koppeling (M). • Demonteer de haarpinveer (E) en verwijder de hefboom. • Demonteer de haarpinveer (A) en verwijder de hefboom. • Demonteer de haarpinveer (D) en verwijder de hefboom.
6 M V R To Replace Mower Drive Belt Austauschen des Antriebsriemens des Mähers MOWER DRIVE BELT REMOVAL 1. Park tractor on a level surface. Engage parking brake. 2. Lower attachment lift lever to its lowest position. 3. Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface. 4. Remove belt from clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (V). ENTFERNEN DES ANTRIEBSRIEMENS DES MÄHERS 1.
6 Sostituzione della cinghia di trasmissione del rasaerba Pour remplacer la courroie de transmission DÉMONTAGE DE LA COURROIE DE TRANSMISSION DE LA TONDEUSE 1. Garez le tracteur bien à plat. Engagez le frein de stationnement. 2. Faites descendre le levier de levage de l’accessoire dans sa position la plus basse. 3. Eliminez la saleté ou les brins d’herbe qui s’accumulent autour des arbres et à la surface du pont supérieur. 4.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 To Level Mower FRONT-TO-BACK ADJUSTMENT Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly. IMPORTANT: Deck must be level side-to-side.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Ausnivellieren des Mähers JUSTIERUNG IN LÄNGSRICHTUNG WICHTIG: Der Mäher muss von Seite zu Seite waagrecht stehen. Um die besten Schnittergebnisse zu erhalten, sollten die Mäherklingen so eingestellt sein, dass die vordere Spitze 1/8" bis 3/8" niedriger als die hintere Spitze ist, wenn der Mäher in seiner höchsten Stellung ist.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 RÉGLAGE D’AVANT EN ARRIÈRE IMPORTANT: Le pont doit être mis à niveau bilatéralment. Pour que la coupe soit parfaite, les lames de la tondeuse doivent être réglées de façon à ce que la pointe avant se trouve 1/8 –3/8" pouce plus bas que la pointe arrière lorsque la tondeuse est dans sa position la plus élevée.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Nivelar el cortacésped AJUSTE DE LA PARTE DELANTERA A LA TRASERA IMPORTANTE: la cubierta ha de ser nivelada de un lado al otro. Para obtener los mejores resultados de corte, las hojas del cortacésped han de ajustarse de modo que la punta frontal sea entre 1/8" y 3/8" más bajo que la punta trasera cuando la cortacésped está en su posición más alta. PRECAUCIÓN: La cuchilla está afilada.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Livellamento del rasaerba REGOLAZIONE DAVANTI-DIETRO IMPORTANTE: La copertura deve essere regolata lato-lato. Per ottenere risultati di rasature ottimali, regolare le lame del rasaerba in modo tale che, quando il rasaerba si trova nella posizione massima, la punta anteriore sia 1/8”-3/8" inferiore rispetto alla punta posteriore. ATTENZIONE: la cuchilla está afilada.
6 Fig. 3 Fig. 1 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 De maaiunit nivelleren AFSTELLING BOOR-EN ACHTERZIJDE BELANGRIJK: Het oppervlak van de maaier moet overal dezelfde hoogte hebben. Voor de beste maairesultaten moeten de maaimessen zodanig worden afgesteld dat de voorkant 1/8” tot 3/8" lager is dan de achterkant wanneer de maaier in de hoogste stand staat.
6 Controlar El Freno To Check Brake Si el tractor requiere más de cinco (5) pies para pararse a la velocidad más alta en la marcha más alta en una superficie nivelada seca en hormigón o adoquinada, hay que reparar el freno. También se puede controlar el freno de la siguiente manera: 1. Aparcar el tractor en una superficie nivelada seca en hormigón o adoquinada, presionar el pedal del freno hasta el fondo y poner el freno de estacionamiento. 2.
6 4. Install belt on centerspan idler (E). 5. Install belt through stationary idler (C) and clutching idler (D). 6. Reinstall anti-rotation link (B) on right side of tractor. Tighten securely. 7. Reconnect clutch harness (A). 8. Make sure belt is in all pulley grooves and inside all belt guides and keepers. 9. Install mower (See “ASSEMBLY OF THE CUTTING UNIT” in this section of manual). G H Austauschen Des Motorantriebsriemens Parken Sie den Traktor auf einer ebenen Fläche. Legen Sie die Handbremse ein.
6 3. Tirez la courroie vers l’arrière du tracteur. Faites passer prudemment la courroie autour du ventilateur de refroidissement de la transmission et autour de la poulie de puissance (F). Vérifiez si la courroie se trouve dans le passant de la courroie. 4. Montez la courroie sur la poulie folle médiane (E). 5. Faites passer la courroie à travers la poulie folle stationnaire (C) et la poulie folle de l’embrayage (D). 6. Remontez la connexion anti-rotation (B) sur le côté droit du tracteur.
6 3. Tirare la cinghia verso la parte posteriore del trattore. Posizionare con cautela la cinghia attorno alla ventola di raffreddamento della trasmissione e sulla puleggia di ingresso (F). Verificare che la cinghia si trovi all’interno del relativo fermo. 4. Installare la cinghia sul pignone folle della sezione centrale (E). 5. Inserire la cinghia attraverso il pignone folle fisso (C) e il pignone d’innesto (D). 6. Reinstallare l'articolazione anti-rotazione (B) sul lato destro del trattore.
6 ENFRIAMIENTO DEL TRANSEJE TRANSAXLE COOLING Las aletas de enfriamiento y el ventilador de la transmisión tienen que mantenerse limpios para asegurar el enfriamiento adecuado. No trate de limpiar el ventilador o la transmisión cuando el motor esté funcionando o mientras la transmisión esté caliente. • Inspeccione el ventilador de enfriamiento para asegurarse que las aspas del ventilador estén intactas y limpias.
6 RECORDATORIO MANTENIMIENTO/CUENTAHORAS SERVICE REMINDER/HOUR METER Service reminder shows the total number of hours the engine has run and flashes to indicate that the engine or mower needs servicing. When service is required, the service reminder will flash for two hours. To service engine and mower, see the Maintenance section of this manual. NOTE: Service reminder runs when the ignition key is in any position but “STOP”.
6 WASCHANLAGEN-ÖFFNUNG DER ABDECKUNG Ihre Traktorabdeckung ist außen mit einer Waschanlagen-Öffnung ausgestattet, die Teil der Waschanlage für die Abdeckung ist. Sie sollte nach jedem Gebrauch eingesetzt werden. • Fahren Sie den Traktor auf eine ebene, saubere Stelle Ihres Rasens, möglichst nah an einen Wasserhahn, an den Sie Ihren Gartenschlauch anschließen können. WICHTIG: Bitte achten Sie unbedingt darauf, dass die Auswurfschütte Ihres Traktors NICHT in Richtung Haus, Garage oder parkende Fahrzeuge usw.
6 BOCA DE LAVADO DE LA PLATAFORMA La plataforma del tractor cuenta con una boca de lavado en la superficie como parte del sistema de limpieza. Se debe utilizar tras cada uso. A • Desplace el tractor a un punto nivelado y despejado del prado, cerca de un grifo al que pueda conectar la manguera. IMPORTANTE: Compruebe que el conducto de descarga del tractor queda orientado hacia OTRO PUNTO que no sea la casa, el garaje, coches aparcados, etc. Retire el depósito de polvo o de hojas si está fijado.
6 DEKREINIGINGSPOORT Het maaidek van uw trekker is aan de bovenkant uitgerust met een reinigingspoort als onderdeel van het dekreinigingssysteem. Dit systeem dient na elk gebruik van de maaier te worden gebruikt. • Rijd de trekker naar een vlakke, open plek op uw gazon, dicht genoeg bij een waterkraan om met de tuinslang te bereiken. BELANGRIJK: Zorg ervoor dat de uitworp van de trekker is weggericht van uw huis, garage, geparkeerde auto’s, enz. Verwijder de opvangbak of mulchplaat indien bevestigd.
7. Troubleshooting. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Motor springt nicht an 1. Kraftstoff fehlt im Kraftstofftank. 2. Defekte Zündkerze. 3. Defekter Zündkerzenanschluß. 4. Schmutz in Vergaser oder Kraftstoffleitung. Start motor will not turn engine 1. Battery flat. 2. Poor contact between cable and battery pole. 3. Connection/disconnection level in wrong position. 4. Main fuse defective. 5.
7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne démarre pas 1. Manque de carburant dans le réservoir. 2. Bougie d'allumage défectueuse. 3. Le câblage de la bougie d'allumage défectueux. 4. Il y a des impuretés dans le carburateur ou dans le circuit du carburant. El motor no arranca 1. No hay combustible en el depósito. 2. La bujía es errónea. 3. La conexión de la bujía está defectuosa. 4. Hay suciedad en el carburador o en el tubo de combustible. Le démarreur n'entraîne pas le moteur 1.
7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. De motor start niet 1. Er is geen benzine in de tank. 2. De bougie is defect. 3. De bougie-aansluiting is defect. 4. Vuil in carburateur of brandstofleiding. De startmotor trekt de motor niet 1. De accu is leeg. 2. Slecht contact tussen kabel en accupool. 3.
8. Storage. 8. Aufbewahrung. 8. Remisage. 8. Conservación. Suivre la procédure suivante une fois la saison terminée: • En fin de saison, suivre la procédure suivante pour le remisage. N’utilisez pas de nettoyeur haute pression pour le lavage. L’eau pourrait s’infiltrer dans le moteur et abréger ainsi la durée de l’appareil. • Nettoyer l'ensemble de la machine et plus particulièrement l'intérieur du carter de coupe.
8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti interventi: • Pulire tutto il tagliaerba e particolarmente sotto il coperchio della falciatrice. Per le operazioni di pulizia, non utilizzare acqua ad alta pressione. L’acqua può infiltrarsi nel motore e nel sistema di trasmissione, riducendo quindi così il tempo di vita della macchina. • Ritoccare danni alla verniciatura per evitare ossidazione. • Cambiare l’olio del motore. • Vuotare il serbatoio della benzina.
08.11.11 BD Printed in the U.S.A.