Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Vous pouvez utiliser de l’essence contenant jusqu’à 10 % d’éthanol (E10) avec cet appareil. L’utilisation d’essence contenant plus de 10 % d’éthanol annulera la garantie du produit.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN • • WARNING. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy of Pediatrics recommends that children be a minimum of 12 year of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of age before operating a riding lawn mower. If fuel is spilled on clothing, change clothing immediately. Never overfill fuel tank. Replace gas cap and tighten securely.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 3.0 Gallons/11,35 L Regular Unleaded Oil Type: (API: SG-SL) SAE 30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: W/Filter: 56 Oz./1,65 L W/out Filter: 48 Oz./1,4 L Spark Plug: Champion RC12YC (Gap: .030"/0,76 mm) Charging System: Battery: Blade Bolt Torque: CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance.
UNASSEMBLED PARTS Also included Mulch Kit Keys Slope Sheet *Installed by Dealer *Brush Guard Kit (1) Quick Connect (2) Keys *Pedal (2) Screw (2) Nut U-Channel ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY ✓CHECKLIST NOTE: You may now roll your tractor off the skid. Follow the appropriate instruction on the next page to remove the tractor from the skid. BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ENSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton. ✓ Battery is properly prepared and charged.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P G H D E F B A M C J K L Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. ENGINE • Move throttle control (D) to slow position.
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 7) • • Put attachment lift lever in desired cutting height slot. Slide pointer tab (T) to desired cutting height as a reminder for next time you mow. The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.
OPERATION TO STOP MOWER BLADES • TO OPERATE ON HILLS Disengage attachment clutch control. CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 10). • • • S • • • Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills.
OPERATION SERVICE REMINDER/HOUR METER TO START ENGINE (See Fig. 3) Service reminder shows the total number of hours the engine has run and indicates when the engine or mower needs servicing. After every 50 hours of operation the oil can icon will stay on for 2 hours or until a manual reset occurs. To reset the display manually turn the ignition switch to the on position, then the off position five times (1 second on, 1 second off). To service engine and mower, see the Maintenance section of this manual.
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with o
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.
MAINTENANCE V-BELTS TO CHANGE ENGINE OIL (See Fig. 16 - 18) Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container.
MAINTENANCE ENGINE OIL FILTER CLAMP Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. NOTE: If needed, remove lower dash covers using steps from "Lower dash cover removal" section of this manual. FUEL FILTER Fig. 20 AIR FILTER CLEANING Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions.
MAINTENANCE DECK WASHOUT PORT (See Fig. 22) Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS • • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. Repeat on opposite side of tractor. • Insert end of link (E) into hole in front mower bracket and secure with washer and retainer spring (J). E A J F H B • Fig.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see step in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 31 & 32) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 33) TO REPLACE MOTION DRIVE BELT (See Fig. 34) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL • Remove mower from tractor. (See “TO REMOVE MOWER” in this section of manual.
SERVICE AND ADJUSTMENTS TO REMOVE WHEEL (See Fig. 35) TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully charged battery. • RED cable last from both batteries. • • Block up axle securely. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.
SERVICE AND ADJUSTMENTS ENGINE TO REPLACE HEADLIGHT BULB • • • • Raise hood. Pull bulb holder out of the hole in the backside of the grill. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. Close hood. TO ADJUST THROTTLE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ES SENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel.
1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
Consumer Wheeled Products - Limited Warranty Husqvarna warrants to the original retail purchaser that this product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred to any subsequent purchaser of this product. Certain components (e.g.
(a) Abrasion to mower decks; (b) Tires damaged by external punctures; (c) Natural discoloration of materials due to ultraviolet light; (d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures; In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including any of the following: (e) (f) Failure to provide or perform required maintenance services as prescr
Consumer Wheeled Limited Warranty Chart 2012 Product/Component Riding Lawn Tractors: Frame, Chassis, Front Axle Engine* Transmission (if made by Husqvarna/Peerless) Transmission (if third party)** XLS Models only - stamped deck shell. Armor Protected Limited Warranty Fabricated Deck shell. Limited Lifetime Warranty Battery Other Non-Expendable Components Residential Zero Turn Mowers ( RZ Only ) Engine* Transmission ** RZ4623 (967009801 & 967009802) RZ5426 (967003601 & 967003602) - stamped deck shell.
Consumer Wheeled Limited Warranty Chart 2012 Consumer (personal, household use only) Product/Component Spreader Robotic Mowers Robotic Mower Battery Parts & Accessories (if purchased) Accessories (e.g., grass catcher, bumper guard accessories, etc. Parts (e.g., belts, blades, etc.
RÈGLES DE SÉCURITÉ Conseils pour l’utilisation en toute sécurité des tracteurs DANGER: CET TRACTEUR PEUT AMPUTER LES MAINS, LES PIEDS ET PROJETER DES OBJETS. L’INOBSERVATION DES RÈGLES DE SÉCURITÉ SUIVANTES PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES ET MÊMES MORTELLES. • Ne pas faire fonctionner la machine sans le bac de ramassage AVERTISSEMENT: Débranchez toujours le complet, la goulotte de décharge ou tout autre dispositif de fil de bougie d’allumage et pour prévenir sécurité en place et en fonction.
RÈGLES DE SÉCURITÉ Conseils pour l’utilisation en toute sécurité des tracteurs III. ENFANTS • • AVERTISSEMENT: LES ENFANTS PEUVENT ÊTRE BLESSÉS PAR CET ÉQUIPEMENT. L'American Academy of Pediatrics recommande que les enfants soient âgés d'au moins 12 ans avant de pouvoir utiliser une tondeuse à conducteur à pied et d'au moins 16 ans dans le cas d'un tracteur à gazon. ENTRETIEN GÉNÉRAL • • • Des accidents tragiques peuvent avoir lieu si l’opérateur ne fait pas très attention en présence d’enfants.
SPÉCIFICATIONS DE PRODUIT Capacité et le type d’essence: 3.0 Gallons/11,35 L L’essence sans plomb normale Type d’huile (API: SG-SL): SAE 30 (supérieure de 32°F/0°C) SAE 5W30 (inférieure de 32°F/0°C) Capacité d’huile: Avec un filtre: Sans filtre: Bougie d’allumage: Champion RC12YC (Écart: .030 po/0,76 mm) Système de chargement: Batterie: 9 Ampères @ 3600 RPM Couple de rotation au boulon de lame: 45-55 Ft. Lbs. (61-75 Nm) AMP/HR: MIN. CCA: DIMENSION: FÉLICITATIONS pour votre achat.
PIÈCES PAS ASSEMBLÉ Inclu Jeu de broyeuse Clé Guide-pente (2) Clés *Posé par le Concessionnaire (1) Connecter d'accouplement du rapide *Jeu de protecteur *Pédale (2) Vis (2) Écrou “U” MONTAGE Votre nouveau tracteur a été monté à l’usine sauf les pièces qui ne sont pas montées pour l’expédition. LES OUTILS EXIGÉS POUR LE MONTAGE DE VOTRE TRACTEUR Un jeu de clé à douille rendra le montage. Les dimensions normales des clés sont inscrites.
MONTAGE ✓LISTE DE CONTRÔLE REMARQUE: Procidez comme suit pour retirer le tracteur de la palette. AVANT D’UTILISER VOTRE TRACTEUR, NOUS VOULONS NOUS ASSURER QUE VOUS RECEVREZ LE MEILLEUR RENDEMENT DE CE PRODUIT DE QUALITÉ ET QUE VOUS EN SEREZ SATISFAIT. AVERTISSEMENT: avant le démarrage, nous vous prions de lire, comprendre et suivre toutes les instructions dans la section Fonctionnement de ce manuel d’instructions. S'assurer que le tracteur soit placé dans une zone bien aérée.
UTILISATION Ces symboles peuvent se montrer sur votre tracteur ou dans les publications fournies avec le produit. Apprenez et comprenez la signification des symboles.
UTILISATION CONNAISSEZ VOTRE TRACTEUR AVANT D'UTILISER VOTRE TRACTEUR, LISEZ CE MANUEL DE L’OPÉRATEUR ET LES REGLES DE SECURITE Comparez les illustrations ci-dessous à celles de votre tracteur afin de vou familiariser avec l'emplacement des différentes commandes et avec les réglages. Gardez ce manuel pour référence . P G H D E F B A M C J K L Fig. 3 Nos tracteurs conforment aux normes de sécurité de l’American National Standards Institute.
UTILISATION L’utilisation d’un tracteur présente le risque de projection des particules dans les yeux qui peuvent causer des blessures sérieuses. Portez toujours des lunettes de sécurité ou une visière pendant que vous utilisez, ou que vous faites des réglages ou des réparations au tracteur. Nous recommandons des lunettes de sécurité ou un masque large de sécurité porté au-dessus des lunettes. MOTEUR - POUR ENGAGER LE FREIN DE STATIONNEMENT (Voir la Fig.
UTILISATION • Placez le levier d’accrochage dans la rainure correspondant à la hauteur désirée. • Faites glisser la languette (T) à la hauteur de tonte désirée à titre de rappel. Excellent lors de la prochaine utilisation. La plage de réglage de la hauteur de coupe est environ de 2,54 cm (1 po.) à 10,16 cm (4 po.). Les hauteurs sont mesurées du terrain à l’extrémité de la lame quand le moteur ne marche pas.
UTILISATION POUR ARRÊTER LES LAMES DE TONDEUSE • POUR UTILISER DANS LES PENTES Déplacez la commande d’embrayage d’accessoire à la position "DÉBRAYÉE". AVERTISSEMENT: N’utilisez jamais le tracteur dans les côtes de plus de 15°. Ne le conduisez jamais en travers des surfaces en pente. ATTENTION: N’utilisez pas la tondeuse sans le déflecteur ou sans le ramasse-herbe (S) s'il y a lieu. (Voir La Fig. 10) • • • S • • • Choisissez la vitesse la plus lente avant de commencer à monter ou descendre une côte.
UTILISATION POUR DÉMARRER LE MOTEUR (Voir la Fig. 3) INDICATEUR D’ENTRETIEN/HOROMÈTRE Quand vous démarrez le moteur pour la première fois ou si le moteur est sans essence, il faut plus de temps pour déplacer l’essence du réservoir au moteur. • Assurez-vous que la commande roue libre soit dans la position d'engrenage engagée. • Asseyez-vous sur le siège, enfoncez la pédale frein et emgagez le frein de stationnement. • Déplacez l’embrayage d’accessoire à la position débrayée (DISENGAGED).
UTILISATION CONSEILS DE TONTE PURGER LA TRANSMISSION • ATTENTION: N’engagez jamais ou ne dégagez jamais le levier de la roue libre pendant que le moteur fonctionne. • Pour assurer l’utilisation correcte et le rendement, il est recommandé que la transmission soit purgée avant d’utiliser le tracteur pour la première fois. Ce procédé enlèvera l’air emprisonné à l’intérieur de la transmission qui se développerait pendant l’expédition de votre tracteur.
ENTRETIEN Vérifiez le système de frein Vérifiez la pression des pneus Vérifiez le système de présence d'opérateur et le système del ROS.
ENTRETIEN TRACTEUR DANGER: N’utilisez que les lames de rechange autorisée par le fabricant de votre tondeuse. L’usage d’une lame n’ayant pas été autorisée par le fabricant de votre tondeuse est dangereux et risque d’endommager votre tondeuse et d’annuler sa garantie. Observez toujours les règles de sécurité quand vous faites l’entretien.
ENTRETIEN COURROIES TRAPÉZOÏDALES DÉPOSE DU COUVERCLE DU TABLEAU DE COMMANDE INFÉRIEUR • Soulevez le capot. • Retirez l’attache du couvercle du tableau de commande inférieur. PRÉCAUTION: Retirez avec soin le couvercle du tableau de commande inférieur en portant attention à ne pas briser les pattes de fixation du couvercle.
ENTRETIEN FILTRE D’HUILE DE MOTEUR BRIDE DE SERRAGE Remplacez le filtre d’huile de moteur chaque saison ou tous les deux (2) changements d’huile si le tracteur a été utilisé plus de 100 heures dans une (1) année. FILTRE À AIR FILTRE D’ESSENCE Votre moteur ne fonctionne pas correctement avec un filtre à air sale. Nettoyez le filtre à air plus souvent si utilisé dans les endroits très poussiéreux ou sales. Voir le manuel du moteur. 00667 Fig.
ENTRETIEN RACCORD DE LAVAGE DU PLATEAU DE COUPE (Voir La Fig. 22) Le plateau de coupe de votre tracteur est équipé à la surface d’un raccord de lavage qui fait partie du système de lavage du plateau de coupe. Il convient de l’utiliser après chaque emploi. 1. Conduisez le tracteur vers un endroit plat et dégagé de votre pelouse, suffisamment près pour atteindre le robinet d’eau destiné au tuyau d’arrosage de votre jardin.
RÉVISION ET RÉGLAGES ADVERTISSEMENT: POUR ÉVITER DES DOMMAGES SÉRIEUX, AVANT DE FAIRE TOUS LES RÉVISIONS OU RÉGLAGES. • • • • • Appuyez sur la pédale de frein et engagez le frein de stationnement. Placez l’embrayage d’accessoire en position débrayée (DISENGAGED). Tournez la clé de contact à la position d’arrêt (STOP) et enlevez-la. Assurez-vous que les lames et toutes les pièces tournantes se soient arrêtées.
RÉVISION ET RÉGLAGES • • FIXEZ LES BRAS DE SUSPENSION LATÉRAUX DE LA TONDEUSE AU CHÂSSIS – Placez l’orifice du bras sur la tige (B) à l’extérieur du châssis du tracteur et fixez solidement à l’aide d’une ressort-arrêtoir. Répétez de l’autre côté du tracteur. • Insérez l’autre embout de la bielle (E) dans l’orifice du support avant de la tondeuse (H) et fixez fermement à l’aide d’une rondelle et d’un ressort-arrêtoir (J). E A J F H B Fig. 26 • • Fig.
RÉVISION ET RÉGLAGES POUR AJUSTER LE NIVEAU LA TONDEUSE AJUSTEMENT AVANT/ARRIÈRE (Voir Figs. 31 et 32) IMPORTANT: La plateforme doit être au même niveau d’un côté et de l’autre. Pour obtenir de meilleurs résultats, les lames de la tondeuse doivent être ajustées de sorte que la pointe avant est 1/8" à 1/2" inférieure à la pointe arrière lorsque la tondeuse est à sa position la plus élevée. Assurez-vous que les pneus soient gonflés jusqu’à la pression en PSI indiquée sur ceux-ci.
RÉVISION ET RÉGLAGES POUR REMPLACER LA COURROIE DE LAME DE TONDEUSE (Voir La Fig. 33) POUR REMPLACER LA COURROIE D’ENTRAÎNEMENT (Voir la Fig. 34) La courroie d’entraînement de lame de tondeuse peut être remplacée sans outils. Garez le tracteur sur un terrain plat. Engagez le frein de stationnement. Stationnez le tracteur sur une surface de niveau. Actionnez le frein de stationnement.
RÉVISION ET RÉGLAGES POUR ENLEVER LES CÂBLES, RENVERSEZ LES PROCÉDURES - POUR ENLEVER LES ROUES (Voir la Fig. 35) • • Fixes solidement des cales sous l'éssieu. Enlevez le couvre-essieu, la bague de retenue et les rondelles pour permettre l’enlèvement de la roue (la roue arrière contient une clé carrée - ne la perdez pas). • Réparez le pneu et rassemblez-le. • Sur les roues arrière seulement: alignez les rainures dans le moyeu de roue arrière et l’essieu. Insérez la clé carrée.
RÉVISION ET RÉGLAGES TRANSMISSION VERROUS ET RELAIS Un câblage desserré ou avarié peut être la cause du mauvais fonctionnement, de l'arrêt ou du non-démarrage du tracteur. • Vérifiez le câblage. ENLEVEMENT/REMPLACEMENT Si votre transmission doit être retirée pour un entretien ou pour être remplacée, elle doit être purgée après avoir été réinstallée et avant de faire fonctionner le tracteur. Voir “PURGEZ LA TRANSMISSION” dans la section Utilisation de ce manuel.
ENTREPOSAGE MOTEUR Préparez immédiatement votre tracteur pour d’entreposage à la fin de la saison ou si le tracteur ne sera pas utilisé pendant une période de 30 jours ou plus. SYSTÈME D’ESSENCE IMPORTANT: C ’EST TRÈS IMPORTANT D’ÉVITER LA FORMATION DES DÉPÔTS DE GOMME DANS LE CARBURATEUR, LE FILTRE D’ESSENCE, LE TUYAU D’ESSENCE OU LE RÉSERVOIR D’ESSENCE PENDANT L’ENTREPOSAGE.
GUIDE DE DÉPANNAGE PROBLÈME Le moteur refuse de démarrer CAUSE CORRECTION 1. 2. Sans essence. Le moteur n’est pas démarré à froid correctement. 1. 2. 3. 4. 5. 6. 7. Le moteur est noyé. Mauvaise bougie d’allumage. Filtre à air sale. Filtre d’essence sale. II y a de l’eau dans l’essence. 3. 4. 5. 6. 7. 8. 9. Le câblage est lâche ou endommagé. Le carburateur demande un réglage. 8. 9. 10. Les soupapes de moteur demandent un réglage. 10. Remplissez le réservoir d’essence.
GUIDE DE DÉPANNAGE PROBLÈME CAUSE CORRECTION Vibrations excessives de la tondeuse 1. 2. 3. La lame est usée, tordue, ou lâche. Un mandrin de lame est tordu. Des pièces sont lâches ou endommagées. 1. 2. 3. Remplacez la lame. Serrez à fond le boulon de lame. Remplacez le mandrin de lame. Serrez les pièces lâches. Remplacez les pièces endommagées. Le moteur marchelorsque le conducteurquittelesiège avec l’embrayage d’accessoire engagé 1. Le système qui détecte la présence du conducteurest défectueux.
GUIDE SUGGÈRE POUR L'ÉVALUATION DES PENTES AFIN D'AMÉLIORER LA SÉCURITÉ D'UTILISATION PLIE Z S UIVA CEC N I T E L S E T S PO UNE I N P T E I N L T LÉS E A 15 D E GRÉ S TONDEZ LES PENTES EN MONTANT OU EN DESCENDANT MAIS, JAMAIS EN TRAVERS 15 DEGRÉS MAX 59
Produits sur roues de consommateur – Garantie limitée Husqvarna garantit à l’acheteur original que ce produit HusqvarnaMD est exempt de vices de matériaux ou de fabrication sous des conditions normales d’utilisation et d’entretien à compter de la date d’achat au détail pour la période de garantie applicable indiquée à l’annexe A. Cette garantie ne peut être transférée à aucun aquéreur subséquent de ce produit Husqvarna®. Certains composants (p. ex.
8. Les dommages résultant du vieillissement normal, de l’usure ou de négligence ne sont PAS couverts. La garantie limitée ne couvre pas les dommages autres que ceux découlant de défauts de matériel ou de fabrication. Les points suivants ne sont PAS considérés comme des défauts de matériaux ou de fabrication et ne sont donc PAS couverts.
Tableau de garantie limitée des produits sur roues de consommateur 2012 Consommateur (perso nnel, utilisation domestique seulement) Commercial (toute utilisation commerciale, professionnelle, institutionnelle, agricole ou à revenu de production, sauf l’utilisation en location) Annexe A Location (toute utilisation en location) Aucune garantie * Aucune garantie ** Aucune garantie * Aucune garantie ** Aucune garantie Aucune garantie Aucune garantie Aucune garantie Aucune garantie Aucune garantie Aucune
Tableau de garantie limitée des produits sur roues de consommateur 2012 Produit/composant Tondeuses robotiques Tondeuse robotique Batterie Pièces et accessoires (si acheté) Consommateur (perso nnel, utilisation domestique seulement) Commercial (toute utilisation commerciale, professionnelle, institutionnelle, agricole ou à revenu de production, sauf l’utilisation en location) Annexe A Location (toute utilisation en location) 2 ans 1 an 90 jours 1 an 90 jours 1 an Aucune garantie Aucune garantie Auc
10/30/2012 BD