03002 917.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuelsoaked debris. Allow machine to cool before storing.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 2.50 Gallons Unleaded Regular Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) Oil Capacity: W/ Filter: W/O Filter: Spark Plug: (Gap: .040") Champion QC12YC Ground Speed (MPH): Forward: Reverse: Charging System: 16 AMPS @ 3600 RPM Battery: AMP/HR: MIN. CCA: Case Size: Blade Bolt Torque: 45-55FT. LBS. CUSTOMER RESPONSIBILITIES • • • 64 oz. 60 oz. Read and observe the safety rules.
UNASSEMBLED PARTS Slope Sheet Key (1) Oil Drain Tube (2) Keys ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping puposes. When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel). ADJUST SEAT (See Fig. 2) • • TO REMOVE TRACTOR FROM CARTON • Sit in seat.
ASSEMBLY • • • Release parking brake by depressing brake pedal. Place freewheel control in disengaged position to disengage transmission (See “TO TRANSPORT” in the Operation section of this manual). Roll tractor forward off skid. ✓CHECKLIST BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P H D E G K L B N F J C A M FIG. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute. (H) LIGHT SWITCH – Turns the headlights on and off.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead.
OPERATION NOTE: Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual). • With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely. • Repeat for all, installing gauge wheel in same adjustment hole. J K L FIG.
OPERATION WARNING: Backing up with the attachment clutch engaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary. Transmission Engaged USING THE REVERSE OPERATION SYSTEM Only use if you are certain no children or other bystanders will enter the mowing area.
OPERATION • Release the parking brake and let the brake slowly return to operating position. • Allow one minute for transmission to warm up. This can be done during the engine warm up period. • The attachments can be used during the engine warm-up period after the transmission has been warmed up and may require the choke control be pulled out slightly.
OPERATION MOWING TIPS • • • • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. The left hand side of mower should be used for trimming. Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T Check Operator Presence & ROS Systems R A Check for Loose Fasteners C Check/Replace Mower Blades T Lubrication Chart 0 Check Battery Level R Clean Battery and Terminals 3 4 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (wi
MAINTENANCE TRACTOR BLADE CARE Always observe safety rules when performing any maintenance. For best results mower blades must be sharp. Replace worn, bent or damaged blades. BRAKE OPERATION CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.
MAINTENANCE • • TO CHANGE ENGINE OIL (See Figs. 14 and 15) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. • Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. • Remove yellow cap from end of drain valve and install the drain tube onto the fitting.
MAINTENANCE MUFFLER CLAMP Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. FUEL FILTER SPARK PLUGS FIG. 16 Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual. CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TRACTOR TO INSTALL MOWER (See Figs. 17-21) TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS M A B FIG. 18 • • ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring. Repeat on opposite side of tractor. FIG. 21 • • Raise attachment lift lever to highest position. If necessary, adjust gauge wheels before operating mower as shown in the Operation section of this manual. C TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires.
SERVICE AND ADJUSTMENTS PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 23) • With all tires properly inflated, park tractor on level ground or driveway. B CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. • • • • A Raise mower to its highest position. At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.
SERVICE AND ADJUSTMENTS • S Install mower (See “TO INSTALL MOWER” in this section of manual). M G H R B A C R J D E FIG. 26 TO REPLACE MOTION DRIVE BELT (See Fig. 27) F 02953 electric Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. FIG. 27 BELT REMOVAL • Remove mower (See “TO REMOVE MOWER” in this section of manual).
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 30) • Replace washers and snap retaining ring securely in axle groove. • Replace axle cover. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time.
SERVICE AND ADJUSTMENTS TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31) ENGINE • • • TO ADJUST THROTTLE CONTROL CABLE • Raise hood. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. To replace, reverse above procedure. The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.
STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING POINTS PROBLEM Will not start Hard to start CAUSE 1. 2. 3. 4. 5. 6. 7. 8. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Weak or dead battery. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Loose or damaged wiring. Carburetor out of adjustment. 9. 10. 11. Engine valves out of adjustment. 11. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine dies when tractor is shifted into reverse 1. 1. Turn ignition key to ROS "ON" position. See Operation section. Reverse operation system (ROS) is not "ON" while mower or other attachment is engaged. Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
TRACTOR - - MODEL NUMBER YTH2242T (279180) SCHEMATIC 02929-194276_Regulated-Tex BATTERY RED SOLENOID STARTER M RED FUSE BLACK ELECTRIC CLUTCH WHITE S WHITE M B BLACK WHITE A1 G L GRAY A2 RED CLUTCH/BRAKE (PEDAL UP) RED BLACK BLACK PTO SWITCH (DISENGAGED) REVERSE SWITCH (NOT IN REVERSE) BLACK BLACK 2 BLACK 3 BLACK BLACK BLACK BLACK 1 6 SEAT SWITCH (NOT OCCUPIED) GRAY BLACK /WHITE JUNCTION CONNECTOR SHORTING CONNECTOR CHASSIS HARNESS SPARK PLUGS GAP (2 PLUGS ON TWIN CYL.
TRACTOR - - MODEL NUMBER YTH2242T (279180) ELECTRICAL 22 21 41 24 43 42 40 27 33 30 25 34 2 27 1 46 91 50 99 100 26 8 ry tte Ba 16 _28 71 29 55 28 194276D 28
TRACTOR - - MODEL NUMBER YTH2242T (279180) ELECTRICAL KEY NO. 1 2 8 16 21 22 24 25 26 27 28 29 30 33 34 40 41 42 43 46 50 55 71 90 91 99 100 PART NO.
TRACTOR - - MODEL NUMBER YTH2242T (279180) CHASSIS 15 208 204 18 210 212 214 203 14 207 130 25 211 206 209 130 5 176 202 176 205 176 177 175 150 178 195 36 176 176 196 37 182 181 152 130 159 194 138 184 181 222 180 219 217 162 165 194 99 219 68 229 183 2 chassis-tex_33-lt husq KEY NO. 2 5 14 15 18 25 36 37 68 99 130 138 150 152 159 162 165 175 176 177 178 180 181 182 PART NO.
TRACTOR - - MODEL NUMBER YTH2242T (279180) STEERING ASSEMBLY 26 45 51 1 54 21 19 16 66 65 63 60 57 63 9 61 8 7 54 67 55 2 59 98 7 6 4 35 58 64 67 28 13 55 15 22 6 14 5 62 50 13 14 15 69 68 53 8 65 50 13 70 steering-tex_5-vgt KEY NO. PART NO.
TRACTOR - - MODEL NUMBER YTH2242T (279180) DRIVE 56 213 125 206 221 207 26 209 92 116 185 197 171 196 221 184 42 35 80 125 125 167 160 203 64 160 188 170 161 52 186 189 187 214 208 49 159 51 15 153 125 50 29 51 190 15 163 215 159 52 51 2 116 17 73 1 1 2 183 205 37 drive-tex_17 32 33 210
TRACTOR - - MODEL NUMBER YTH2242T (279180) DRIVE KEY NO. PART NO.
TRACTOR - - MODEL NUMBER YTH2242T (279180) ENGINE 22 83 1 21 20 62 69 18 45 71 84 84 82 15 70 81 12 79 11 37 28 41 42 31 37 85 90 2 9 29 SPARK ARRESTER KIT engine-tex_26 KEY NO. PART NO. 1 ------ 2 9 11 12 15 18 20 21 22 28 29 31 37 41 532 14 97-23 532 19 43-19 532 18 05-05 532 19 43-38 532 19 70-24 532 19 59-51 532 17 83-85 532 19 16-11 532 19 15-96 532 40 11-35 532 13 71-80 532 14 50-06 532 12 34-87 532 12 61-97 DESCRIPTION Engine B&S Model No.
TRACTOR - - MODEL NUMBER YTH2242T (279180) MOWER LIFT 7 87 87 90 98 89 3 10 88 97 2 97 91 lift-tex_4 KEY NO. PART NO. DESCRIPTION 2 3 7 10 87 88 89 532 19 52-23 532 19 52-31 532 19 64-92 532 19 63-14 532 19 42-09 532 19 53-03 819 19 19-12 Shaft Asm., Lift Lever Asm., Lift Rh Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc KEY NO. 90 91 97 98 PART NO.
TRACTOR - - MODEL NUMBER YTH2242T (279180) SEAT ASSEMBLY 1 8 8 7 7 41 40 10 21 6 37 5 37 2 44 43 21 3 seat-tex_7-vgt KEY NO. 1 2 3 5 6 7 8 10 PART NO. 532 19 75-18 532 18 01-66 532 14 06-75 532 14 50-06 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 DESCRIPTION Seat Bracket Pivot Fender Strap, Asm Fender Clip, Push In, Hinged Nut, Lock W/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 uncx 3/4 w/Sems Pan, Seat KEY NO. PART NO.
TRACTOR - - MODEL NUMBER YTH2242T (279180) DECALS 2 7 4 5 6 2 9 3 1 11 8 12 KEY NO. PART NO. DESCRIPTION KEY NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 532 40 21-04 532 40 28-32 532 40 35-27 532 40 21-28 532 18 09-41 532 40 35-70 532 40 44-84 532 18 94-89 Decal, Operators Decal, Hood Decal, Hood Panel SD Decal, Hood Top Insert Decal, Customer Respons. Decal, Replacement Decal, Steering Wheel Decal, Eng.
TRACTOR - - MODEL NUMBER YTH2242T (279180) MOWER DECK 40 145 59 57 55 68 56 34 190 33 40 116 117 32 36 31 30 40 196 1 21 21 40 196 117 188 69 189 19 21 116 62 6 21 189 188 24 6 19 23 25 16 26 20 15 29 27 69 14 69 13 11 8 42_D_elec-Tex_8 38
TRACTOR - - MODEL NUMBER YTH2242T (279180) MOWER DECK KEY NO. PART NO.
TRACTOR - MODEL NO. 917.
TRACTOR - MODEL NO. 917.279180 (YTH2242T) HYDRO TRANSAXLE - - MODEL NUMBER 356-0510 KEY NO. PART NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.279180 BRIGGS ENGINE - MODEL NUMBER 441777, TYPE NUMBER 0284-E1 KEY NO. PART NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.279180 BRIGGS ENGINE - MODEL NUMBER 441777, TYPE NUMBER 0284-E1 KEY NO. PART NO.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA L O NG D THIS O I T S T A E D LIN 1 5 DEG E RE E S LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
532 40 40-32 Rev. 3 05.16.06 TR/VB Printed in U.S.A.
