07002 YTH23V48 Owner's Manual 532 43 87-22 Rev.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. • Be alert and turn machine off if a child enters the area.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 3 Gallons Unleaded Regular Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) Oil Capacity: w/Filter: w/o Filter: Spark Plug: Champion QC12YC (Gap: .040") Ground Speed (MPH): Forward: Reverse: Charging System: 16 AMPS @ 3600 RPM Battery: AMP/HR: MIN. CCA: Case Size: Blade Bolt Torque: 45-55 FT. LBS. CUSTOMER RESPONSIBILITIES • • • 64 oz 60 oz Read and observe the safety rules.
UNASSEMBLED PARTS Slope Sheet Key (1) Oil Drain Tube (2) Keys ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY • A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY ✓CHECKLIST CHECK TIRE PRESSURE BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P B H D A G E F C K J M L Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute. (H) LIGHT SWITCH - Turns the headlights on and off.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR ENGINE • Move throttle control (D) between half and full speed (fast) position.
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 7) • Put attachment lift lever in desired cutting height slot. The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to approximately 2-1/2 " during the cool season and to over 3"during hot months.
OPERATION • CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 10). • • • S • • Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills. If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake. To restart movement, slowly release parking brake and brake pedal. Slowly depress appropriate drive pedal to slowest setting.
OPERATION BEFORE STARTING THE ENGINE TO START ENGINE (See Fig. 3) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brake. • Move attachment clutch to “DISENGAGED” position. • Move throttle control to choke position.
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with o
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.
MAINTENANCE V-BELTS OIL DRAIN VALVE Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. TRANSAXLE COOLING CLOSED AND LOCKED POSITION The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot.
MAINTENANCE MUFFLER DECK WASHOUT PORT (See Fig. 19) Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig. 20) TO INSTALL MOWER (See Figs. 20 - 32) • • • 1.
SERVICE AND ADJUSTMENTS 5. INSTALL ANTI-SWAY BAR (S) (IF EQUIPPED) (See Fig. 26 - 28) 2. ASSEMBLE FRONT GAUGE WHEEL (W) TO FRONT OF MOWER (See Fig. 23) H H. FRONT MOWER BRACKET W. FRONT GAUGE WHEEL X. SHOULDER BOLT Y. 1-1/4 O.D. WASHER Z. 3/8-16 LOCKNUT W X Z Y ANTI-SWAY BAR (S) TOWARDS TRANSAXLE TOWARDS MOWER DECK 90° END INTEGRATED WASHER END Fig. 26 Fig. 23 3. TURN STEERING WHEEL LEFT AND POSITION MOWER (See Fig.
SERVICE AND ADJUSTMENTS • Insert other end of link (E) into hole in front mower bracket (H) and secure with washer and small retainer spring (J). NOTE: Requires deck lifting. 6. ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 29) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor. A FRONT LINK LOCATION M B D H F G A. MOWER SIDE SUSPENSION ARMS B.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 33) • Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position. The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center. MOWER DRIVE BELT REMOVAL • Park tractor on a level surface.
SERVICE AND ADJUSTMENTS NOTE: Each full turn of the adjustment nut will change mower height about 1/8". • Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip. • Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut. 02966 A A Fig. 35 • If adjustment is necessary, see steps in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal.
SERVICE AND ADJUSTMENTS TO START ENGINE WITH A WEAK BATTERY (See Fig. 40) G WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. H B A If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manual).
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 41) TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 39) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. • • • • • • • • • • • • HOOD Lift hood to raised position. Remove terminal cover.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 DECALS 16 15 17 16 1 14 14 2 9 6 5 KEY NO. 1 2 5 6 8 9 14 15 PART NO. 532 41 16-57 532 42 41-02 532 17 84-55 532 42 95-57 532 19 87-85 532 14 50-05 532 43 95-77 532 42 38-29 8 DESCRIPTION Decal, Warning Decal, Warning Decal, Caution Decal, Eng. Decal, Mower Sch. Decal, Battery Dnge/Poi Decal, Panel Side Decal, Cust. Resp. WHEELS AND TIRES 1 2 11 3 4 7 10 5 6 9 8 KEY NO. 16 17 ------ PART NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 ELECTRICAL KEY NO. PART NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 CHASSIS KEY NO. 3 5 14 15 18 25 34 36 37 52 68 130 137 150 151 152 161 162 165 175 176 177 178 180 182 183 189 191 194 PART NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 DRIVE KEY NO. PART NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 ENGINE KEY NO. PART NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 2 4 5 6 7 8 9 13 14 15 16 19 21 22 26 28 35 45 51 53 57 58 59 60 61 62 63 64 66 67 68 69 70 Wheel, Steering Axle Asm., Front Spindle Asm., LH Spindle Asm., RH Bearing, Race Thrust Harden Washer 25/32 x 1-5/8 x 16 Ga. Ring, Clip #T5304-75 Cap, Spindle Washer 25/32 x 1-1/4 x 16 Ga.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 MOWER DECK KEY PART NO. NO. DESCRIPTION 1 6 7 8 11 12 13 14 15 16 17 18 19 20 21 22 24 25 26 27 29 30 31 32 33 39 43 46 47 48 Deck Weldment Mower Cover Mandrel LH Cover Mandrel RH Bolt 7/16 Asm. Blade Blade High Lift Rod Anti-Sway Shaft Asm. w/Lower Bearing Housing, Mandrel Bearing, Ball, Mandrel Washer 13/32 x 13/16 x 12 Ga.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 MOWER LIFT 7 87 87 90 98 89 3 10 88 97 2 91 97 91 87 89 lift-tex_3 89 87 KEY NO. 2 3 7 10 87 88 89 PART NO. 532 42 20-27 532 19 52-31 532 41 15-55 532 19 63-14 532 19 42-09 532 41 07-10 819 19 19-12 KEY NO. DESCRIPTION Shaft Asm. Cross, Lift Lever Asm., Lift Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc 90 91 97 98 PART NO.
TRACTOR - MODEL NO. YTH23V48 (96043012500), PRODUCT NO. 960 43 01-25 SEAT ASSEMBLY 1 8 8 7 7 8 41 8 40 10 6 21 37 37 44 2 43 21 3 seat-tex_6.5SL_2 KEY NO. PART NO. DESCRIPTION 1 2 3 6 7 8 10 21 532 42 40-68 532 18 01-66 532 14 06-75 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 532 17 18-52 Seat Bracket Pivot Fender Strap, Asm Fender Nut, Lock w/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 unc x 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18 KEY NO. PART NO.
1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
Consumer Wheeled Products – Limited Warranty Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. Certain components (e.g., engines and transmissions) are excluded from coverage, and other limitations apply, as described in this document.
c. Preventative maintenance as outlined in the operator’s manual. In addition, you must cease using the product immediately upon any failure or damage. The product should be taken to an authorized Husqvarna servicing dealer prior to any further use. 4. Damages resulting from normal aging, wear and tear or neglect are NOT covered. The Limited Warranty does not cover damage other than that resulting from defects in material or workmanship.
Consumer Wheeled Warranty Chart 2010 Exhibit A Product/Component Riding Lawn Tractors: Frame, Chassis, Front Axle Engine* Transmission (if made by Husqvarna/Peerless) Transmission (if third party)** Battery Other Non-Expendable Components Residential Zero Turn Mowers ( RZ Only ) Engine* Transmission ** Battery Other Non-Expendable Components Residential Zero Turn Mowers ( MZ & EZ ) Engine* Transmission ** Battery Other Non-Expendable Components LE475 Edger Engine* Other Non-Expendable Components Walk Behin
Consumer Wheeled Warranty Chart 2010 Exhibit A Consumer (personal, household use only) Commercial (any commercial, professional, institutional, arigculutral, or income producing use, other than Rental Use) Product/Component Front Mounted Deck Riders * * Engine* Transmission 2 Years NO WARRANTY Battery 1 Year Pro-rated NO WARRANTY Other Non-Expendable Components 2 Years NO WARRANTY Cultivators Battery 1 Year Pro-rated NO WARRANTY Other Non-Expendable Components 2 Years NO WARRANTY Pressure Washers Model 55
