03002 YTH2754XP Owner's Manual
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuelsoaked debris. Allow machine to cool before storing.
PRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES Gasoline Capacity and type: 4 Gallons Unleaded Regular • • Oil Type (API-SG-SL): SAE 10W30 (above 32°F) SAE 5W-30 (below 32°F) • Oil Capacity: W/ Filter: Spark Plug: (Gap: .030") Champion RC12YC Ground Speed (MPH): Forward: Reverse: Charging System: 15 AMPS @ 3600 RPM Battery: AMP/HR: MIN. CCA: Case Size: Blade Bolt Torque: 45-55FT. LBS. 1.8 QT Read and observe the safety rules.
UNASSEMBLED PARTS Mower (5) Large Retainer Springs - 7/16 Mower Front Wheel (1) 3/4 O.D. Washers (1) Wheel (1) 1-1/4 O.D. Washer (2) Smaller Retainer Springs - 5/16 (5) 1-3/16 O.D.
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY ADJUST SEAT (See Fig. 2) A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY • 02 05 Slowly depress forward drive pedal and drive tractor off skid. • Apply brake to stop tractor and set parking brake. • Turn ignition key to "STOP" position. Continue with the instructions that follow. 1 ASSEMBLE FRONT WHEEL TO MOWER (See Fig. 3) • Using shoulder bolt, washer and locknut from parts bag, assemble front wheel to mower as shown. Tighten securely. A FIG. 5 NOTE: Be sure mower side suspension arms (A) are pointing forward before sliding mower under tractor.
ASSEMBLY • • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with washer and retainer spring. Repeat on opposite side of tractor. • • • A Turn steering wheel to position wheels straight forward. ATTACH FRONT LINK (E) - Work from left side of tractor.
ASSEMBLY ✓CHECKLIST M BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton. ✓ Battery is properly prepared and charged. ✓ Seat is adjusted comfortably and tightened securely. ✓ All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P H D E G K L N B F J C A M FIG. 13 Our tractors conform to the applicable safety standards of the American National Standards Institute. (H) LIGHT SWITCH – Turns the headlights on and off.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead.
OPERATION • • J The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height. TO ADJUST GAUGE WHEELS (See Fig.
OPERATION • • S • To restart movement, slowly release parking brake and brake pedal. Slowly depress appropriate drive pedal to slowest setting. Make all turns slowly. TO TRANSPORT (See Figs. 13 and 21) When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. • Raise attachment lift to highest position with attachment lift control.
OPERATION • BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped, from the factory, already filled with summer weight oil. • Check engine oil with tractor on level ground. • Unthread and remove oil fill cap/dipstick; wipe oil off. Reinsert the dipstick into the tube and rest oil fill cap on the tube. Do not thread the cap onto the tube. Remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.
OPERATION • Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual). • Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. Disengage parking brake • Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five (5) seconds and release pedal.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T Check Operator Presence & ROS Systems R A Check for Loose Fasteners C Check/Replace Mower Blades T Lubrication Chart 0 Check Battery Level R Clean Battery and Terminals 3 4 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (wi
MAINTENANCE TRACTOR BLADE CARE Always observe safety rules when performing any maintenance. For best results mower blades must be sharp. Replace worn, bent or damaged blades. BRAKE OPERATION CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.
MAINTENANCE • • TO CHANGE ENGINE OIL (See Figs. 24 and 25) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. • Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. • Remove yellow cap from end of drain valve and install the drain tube onto the fitting.
MAINTENANCE ENGINE OIL FILTER CLAMP Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. CLAMP MUFFLER FUEL FILTER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. FIG. 26 CLEANING SPARK PLUGS • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. • TRACTOR (See Fig.
SERVICE AND ADJUSTMENTS • • Go to side of mower you wish to adjust. With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to the left to lower the mower, or, to the right to raise the mower. FRONT-TO-BACK ADJUSTMENT (See Figs. 30 and 31) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position. CAUTION: Blades are sharp.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT TO CHECK BRAKE MOWER DRIVE BELT REMOVAL (See Fig. 32) • Park tractor on a level surface. Engage parking brake. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L). If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.
SERVICE AND ADJUSTMENTS • Replace axle cover. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. G H B WASHERS RETAINING RING A AXLE COVER C J D E SQUARE KEY (REAR WHEEL ONLY) FIG. 34 F TO START ENGINE WITH A WEAK BATTERY (See Fig. 35) 02953 electric WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries.
SERVICE AND ADJUSTMENTS TO REPLACE HEADLIGHT BULB • • • • Raise hood. Pull bulb holder out of the hole in the backside of the grill. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. Close hood. HOOD HEADLIGHT WIRE CONNECTOR INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts section.
STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING POINTS PROBLEM CAUSE Will not start 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Weak or dead battery. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. 8. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Recharge or replace battery. Clean/replace air filter. Replace fuel filter.
TROUBLESHOOTING POINTS PROBLEM CAUSE Engine dies when tractor is shifted into reverse 1. Reverse operation system (ROS) is not "ON" while mower or other attachment is engaged. 1. Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 ELECTRICAL KEY NO. 1 2 8 16 21 22 24 25 26 27 28 29 30 33 34 40 41 42 43 46 50 55 71 90 91 99 100 PART NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 CHASSIS KEY NO. 5 14 15 18 25 34 37 52 58 68 99 130 139 150 152 156 161 162 165 175 176 177 178 180 181 182 PART NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 DRIVE KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 STEERING ASSEMBLY 26 45 51 1 21 63 19 16 60 57 63 9 61 8 7 66 67 2 59 98 7 6 4 35 58 64 67 28 13 15 22 6 14 5 69 68 62 13 14 15 53 8 70 steering-tex_4-husq 13 KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 ENGINE 1 21 20 87 81 82 22 18 84 62 45 15 69 37 12 28 37 11 70 31 71 86 41 42 85 2 9 29 90 SPARK ARRESTER KIT engine-tex_14-kohl KEY NO. 1 2 9 11 12 15 18 20 21 22 28 29 31 37 41 42 45 62 69 PART NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 SEAT ASSEMBLY 1 8 8 7 7 41 40 10 21 6 37 5 44 37 2 43 21 3 seat-tex_5-husq KEY NO. PART NO. DESCRIPTION 1 2 3 5 6 7 8 10 21 532 19 75-26 532 18 01-66 532 14 06-75 532 14 50-06 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 532 17 18-52 Seat Bracket Pivot Fender Strap, Asm Fender Clip, Push In, Hinged Nut, Lock W/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 uncx 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18 KEY NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 DECALS 16 13 2 16 11 14 14 5 3 8 7 9 15 15 12 6 10 1 KEY NO. 1 2 3 5 6 7 8 9 10 11 PART NO. 532 15 97-37 532 40 21-28 532 19 63-57 532 18 21-66 532 19 68-41 532 14 08-37 532 19 87-85 532 14 50-05 532 17 83-02 532 40 03-89 DESCRIPTION Decal, Brake/Clutch Sym Decal, Hood Insert Decal, Warning Deflect. Cutfinger Decal, Cutfinger CE Decal, Warning Eng. Syms Decal Saddle Brake Parking Decal, Mower Sch.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 MOWER DECK KEY NO. PART NO.
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05 MOWER LIFT 7 87 87 90 98 89 3 10 88 97 2 97 91 87 89 lift-tex_3 89 87 KEY NO. PART NO. DESCRIPTION 2 3 7 10 87 88 89 532 19 52-23 532 19 52-30 532 19 64-92 532 19 63-14 532 19 42-09 532 19 53-04 819 19 19-12 Shaft Asm., Lift Lever Asm., Lift Rh Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc KEY NO. PART NO.
1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
532 40 76-63 07.18.06 Printed in U.S.A.
