Description The VWHDOWK52200 ™ is a customized Reverse Osmosis water filter that is capable of reducing up to 99% of most contaminants. This system is designed for use with hydroponic or horticultural applications. This system is built to give the maximum amount of flow from the membranes while sending less waste water to the drain, compared to similar RO filters. Please read the following setup and maintenance guide to get the maximum results from your filter.
Precautions: t Do not install the unit where the source/inlet pressure may be more than 80 psi or there are excessive water hammer/spike problems. If your inlet pressure is more than 80 psi, install a 3/8” pressure regulator (HL#10071 see pg. 12), available at your dealer or through Hydro-Logic. If you suspect you may have a problem with water hammer or pressure spikes, use the high limt pressure gauge (HL#19306 see pg. 13) to determine what your upper pressure reading is.
Filter Replacement Schedule: Hydro-Logic Part Number Replacement Schedule Membrane Elements (2 per unit) 22120 6 months - 2 years Carbon Filter - Green - Coconut 10” x 2.5” 22110 1,250 gallons of purified water Sediment Filter - Pleated 10” x 2.
TFC Membrane Rejection Chart PolyP
VWHDOWK52200 ™ Unit Includes: VWDJH 5HYHUVH 2VPRVLV :DWHU )LOWHU 6WDJH - Pleated, Cleanable Sediment Pre-Filter UHGXFHV GLUW VHGLPHQW VLOW UXVW HWF 6WDJH - Green Coconut Carbon Block Pre-Filter UHGXFHV FKORULQH DQG RWKHU WR[LQV 6WDJH - 100 GPD Reverse Osmosis Membrane X2 UHGXFHV WRWDO GLVVROYHG VROLGV Inlet Pressure Gauge VKRZV G\QDPLF OLQH SUHVVXUH DQG RSWLPDO RSHUDWLQJ ]RQHV 5 feet white 3/8” inlet tubing, 8 feet black 1/4” waste water tubing
VWHDOWK52200 ™ Setup &RQQHFWLRQV Feed Line From Carbon Filter to Membranes Purified Water Lines (Blue) Waste Water Lines (Black) Automatic Shut-off Valve Flow Restrictor ,QLWLDO 6HWXS Push in the 3/8" white inlet tubing into the 3/8” QC pressure gauge fitting. Connect the 1/4” blue purified water tubing to the outlet of the Automatic Shut-off valve. The system comes with a 3:1 waste water to purified water ratio.
VWHDOWK52200 ™ Setup (cont) Source/Inlet Line (White) Purified Water Line (Blue) Waste Water Line (Black) Upon intial start up of system, slowly turn the source water on until both the carbon and sediment filters have water in the housings. Next, open source water up all the way (do not exceed 80 psi). Flush the system for 30-45 minutes when the system is new and/or when you replace your membranes. This will flush out the food grade preservative in the membranes.
Push In/QuickConnect Fittings &RQQHFWLQJ 3XVK ,Q )LWWLQJV /LQN 7R ,QVWUXFWLRQ 9LGHR youtu.be/EhWXj6DWcH0 Push tubing firmly into the fitting, all the way to tube stop. The collet (gripper) has stainless steel teeth which hold the tube firmly in position while the 'O' Ring provides a permanent leak proof seal. Pull tubing to check for security. If some tube pulls out, then push all the way in again until it stops. It is good practice to test the system prior to leaving site and/or before use.
Filter Changes / Maintenance (cont.) Dirt can become embedded in the sediment filter and cause slower flow rates. Use the included filter wrench to loosen the filter housing. Be careful not to overtighten when reinstalling. It is preferable to hand tighten filter housings after a filter change.
Filter Changes / Maintenance (cont.) 67(3 Firmly grip the membrane housing and twist the membrane cap counter clockwise using the provided filter wrench. 67(3 You can now remove the membrane with either a strong set of needle nose pliers or something similar. Hold onto the membrane housing body and pull straight out until you release the membrane. It may seem tight, but with even pressure it will come out.
Changing the RO Membrane (cont.) 67(3 Push the new membranes back into the housing with the end that has the two black o-rings going in first. Push firmly until it bottoms out and can’t go in further. Then thread the cap back on tightly and reconnect the white 1/4" tubing. 67(3 Follow the same steps for changing the second membrane. Flush the system for 30-45 minutes before using.
Options %RRVWHU 3XPS +/ For low inlet pressure under 40 PSI. Boosts pressure to 60+ PSI, giving faster flow rates. Simply connects onto the source/inlet line. 0HPEUDQH )OXVK .LW +/ Extends life of your RO membranes. Manually power flushes the membranes and clears away scale build up. )ORDW 9DOYH ´ +/ Fill any tank or reservoir unattended. Can be installed in lid or sidewall of tank. NEVER FLOOD YOUR GARDEN AGAIN! .
'H ,RQL]DWLRQ $GG 2Q .LW +/ This de-ionization filter is designed to serve as a post-polishing stage for any Reverse Osmosis system delivering ultra pure 000 PPM water. Color-changing resin indicates when it is time for a replacement. 89 6WHULOL]HU .LW +/ Kills 100% of all bacteria and viruses. Ensures the safest water. 3UHVVXUH *DXJH +LJK /LPLW +/ Measures static pressure as well as high limit pressure. Used to diagnose water hammer or pressure spike issues.
Component Specifications 6HGLPHQW )LOWHU 3OHDWHG &OHDQDEOH t 5 micron nominal filtration t SURFACE AREA: Approximately 4 sq. ft. (0.37 M2) t TEMPERATURE LIMIT: Up to 140°F (60°C) depending on pressure and time under load t FILTER MEDIA: Polyester - Plus ™ t END CAPS: Plastisol (pliable PVC) &DUERQ )LOWHU &RFRQXW (DUWK )ULHQGO\ Hydro-Logic is proud to introduce the first Carbon Block to use NSF61 listed Greencarbon.
Component Specifications (cont.) 52 0HPEUDQHV VWHDOWK52200 ™ TF Membrane Elements are recognized as one of the industry’s most reliable and highest performing membrane elements that deliver consistent performance and quality. Advanced membrane technology and manufacturing processes allow these elements to deliver consistent results.
Warranty & Support A one year warranty against manufacturer's defects comes with each unit. This does not include clogged or damaged prefilters or RO membranes due to lack of regular maintenance or excessive sediment, chlorine, chloramines, iron, silica, manganese, sulfur or Parts Per Million in the source water. This warranty also excludes damage to units caused by using the unit outside of the specified operating parameters listed on page 15.
Notes
370 Encinal Street Suite 150 Santa Cruz, CA 95060 ph: 888.H20.LOGIC / (888.426.5644) fax: 831.336.9840 info@hydrologicsystems.com www.hydrologicsystems.